Nexgrill 920-0010 Kurzanleitung
INSTALLATION INSTRUCTIONS
AND
OWNER’S MANUALS
IMPORTANT
Read this manual carefully before assembling, using or servicing this
heater. Keep this manual for future reference. If you have questions about
assembly, operation, servicing or repair of this heater, please call Nexgrill
Industries., Inc at 1-866-984-7455
OUTDOOR PATIO HEATER
Model 920-0010
Warning: For outdoor Use Only
A02Y07P-2
1
®
Table of Contents
General Safety Information
This manual contains important information about the assembly, opera-
tion and maintenance of this portable heater. General safety information
Presented in these first few pages and is also located throughout the man-
ual. Particular attention should be paid to information accompanied by the
Safety alert symbols: DANGER, WARNING, CAUTION
Keep this manual for future reference and to educate new users of this
Product. This manual should be read in conjunction with the labeling on the
Product.
Safety precautions are essential when any mechanical or propane fueled
Equipment is involved. These precautions are necessary when using, stor-
Ing, and servicing. Using this equipment with the respect and caution
Demanded will reduce the possibilities or personal injury or property damage
The following symbols shown below are used extensively throughout this
Manuals. Always heed these precautions, as they are essential when using
Any mechanical or fueled equipment.
DANGER
DANGER indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury
WARNING
WARNING indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury
CAUTION
DANGER indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury
CAUTION
If you smell gas:
1. Shut off gas to the appliance
2. Extinguish open flame
3. If odor continues, immediately call your gas
supplier.
Table of contents & Warning…………………………2 -3
Tools and parts needed for assembly………………….4
Assembly Instruction…………………………………..5-10
Gas Requirement & Leak testing……………………...11
Safety Checks……………………………………………12
Location heater for use………………………………13-15
Storage burner removal…………………………………16
Burner installation / Pilot cleaning……………………..17
Trouble Shooting…………………………………………18
Part List……………………………………………………19
Limited Warranty…………………………………………20
2
PRECAUTIONS
¾Do not use this space heater in an explosive atmosphere.
Keep heater away from areas where gasoline or other
flammable liquids or vapors are stored.
¾Prior to use, check for damaged parts such as hoses
regulator, pilot or burner.
¾Do not attempt to alter unit in any manner. EXAMPLE:
using the heater without the top canopy reflector or radiant
screen. Do not shorten the burner post assembly.
¾Heater must always be placed on a solid and level surface.
¾Always maintain proper clearance to combustible materials.
Top 18” (46cm) Side 24” (61cm).
¾Always assure there is ample fresh air ventilation for
outdoors use ONLY.
¾Never replace or substitute the regulator with any regulator
other than the factory suggested replacement.
¾Do not clean heater with cleaners that are combustible or
corrosive
¾Do not paint radiant screen, control panel or top canopy
reflector.
¾All leak tests should be done with a soapy solution NEVER
USE AN OPEN FLAME TO CHECK FOR LEAKS.
¾The LP tank should be turned off when the heater is not in use
¾At least once a year, the unit should be inspected for the presence
of spiders, spider webs or other insects. The burner area is a
common spider haven and can damage the heater and render it
unsafe for use, Check the heater immediately if any of the
following exists:
1. The smell of gas in conjunction with extreme yellow tipping of
the burner flames
2. The heater does nor reach temperature.
3. The burner makes a popping noise during use (a slight popping
noise is normal when the burner is extinguished).
¾The LP regulator/ hose assembly should be located out of
pathways Where people may trip over it or in area where the hose
will not be subject to accidental damage.
¾Children and adults should be aware of hazards of high surface
temperature and should stay away to avoid burns of clothing
ignition.
¾Young children should be carefully supervised when they are in
the area of the heater.
¾Clothing or other flammable material should not be hung from the
heater, or placed on or near the heater.
3
NOTE: 20 pound (9.0 kgs), 5 Gallon (18.9 liters) LPG Tank is not supplied
Tools Needed:
Phillips Head Screwdriver
Two Adjustable Opening Wrenches
Spray Bottle of Soapy Water (To check for leaks)
Parts supplied:
Electronic Ignitor Module (1)Granite Table (1)
Tank Hook (1)Post (1)
LPG Gas regulator with Hose (1)Emitter Screen (2)
Gas Tank Enclosure Assembly (1)Heater Head With PVC Hose Assembly (1)
Pole with Support Bracket (1)Emitter Grid (1)
Granite Table Rubber Ring (1)Reflector (3)
Rubber Post Gasket (1)Reflector Plate (1)
Railing (2)Reflector Dome Cap (1)
Hardware Bag
4
Tank hook Ø 3/16 x 4 Flat Head Screw(4)
Tank hook Ø 3/16 x 4 Flat Washer(4)
Reflector Ø1/4” x 82mm Threaded Ends Stud (1)
Reflector Nut (1)
Reflector Ø 1/4”x 8mm Truss Head Screw (3)
Reflector Ø5/32” x 8 mm Truss Head Screw (6)
Heater Body Ø 1/4” x 25mm Flat Head Screw (3)
Secure Guard Ø 1/4” Flat Washer (4)
Secure Guard Ø 1/4” x 20mm Truss Head Screw (4)
Emitter Grid Ø3/16” x 10mm Truss Head Screw (4)
Granite Table Ø 1/4” x 15mm Truss Head Screw (2)
Support Pole Ø 1/4” Spring Washer (4)
Support Pole Ø 1/4” Flat Washer (4)
Support Pole Ø 1/4” Nut (4)
TOOLS AND PARTS NEEDED FOR ASSEMBLY
For Service Questions Replacement parts or other assistance, Please call Nexgrill Customer Service
Hotline at: Nexgrill Industries, Inc
280 Machlin Court, City of Industry, CA91789
(866)984-7455
Assembly Instruction
STEP 1. Attach Pole with Support
Bracket
●Put the Pole with Support Bracket
into the Tank hole.
●Secure the Pole with 4 pcs the 1/4”
Flat Washers, 1/4” Lock Washers and
1/4” Nuts
STEP 2. Secure the Granite Table
●Align the cut out portion of the
Granite Table Rubber Ring with the
openings in the Granite Table Support
Bracket
●Align the screw holes in the
underside of the Granite Table with the
holes in the Granite Table Support
Bracket. Using 2 - 1/4” x 15mm Truss
Head Screw, attach the Granite Table
to the Granite Table Support Bracket as
shown in the diagram to the left.
5
Assembly Instruction
STEP 4. Attach the Post
●Put the head assembly into the post.
●Please make sure the Gas Hose
End and two wires go through the post.
Do not secure the heat assembly in
this step.
STEP 3. Attach the Emitter Grid
●Put the Emitter Grid on the Emitter
base.
●Secure the Emitter Grid with 4pcs
3/16” x 10mm Truss Head Screws as
shown in the diagram to the left.
6
Assembly Instruction
STEP 5. Heater Body Assembly
●Put the Post into the hole of
Granite Table. Please make sure that
the Gas Hose End and two Wires go
through the hole and can be reached
from the interior of the Base Housing.
●Turn the Post clockwise until it
is tightly secured.
●Turn the head assembly to align
the Control Panel to the same side as
the Door of the Base Housing.
Secure the Heater Body with 3pcs 1/4”
x 25mm Flat Head Screws as shown
in the diagram to the left.
STEP 6. Emitter Screen Assembly
●The Emitter Screen comes as two
pieces which fit together just under the
base of the Emitter Screen. Needed for
this step are 4 - 1/4” x 20mm Truss
Head Screws and 4 - 1/4” Flat Washers.
●Align the open area at the bottom of
the Emitter Screen with the four holes in
the Control Panel Housing and using the
4 screws with washers installed on the
screws attach the Emitter Screen to the
Control Panel Housing as shown in the
diagram to the left.
7
Assembly Instruction
STEP 7. Attach the Regulator
●Attached and turn the flare adapter
on the hose end of Regulator
assembly to the flare fitting on the
Gas Hose with adjustable wrenches.
STEP 8. Connect the Igniter Wires
●There should be two wires hanging
down in the Base Housing. The
connectors on the ends of the wires
are different sizes.
●Connect the ends with the
appropriate sized receptacles on the
top of the connector block in the
interior of the Base Housing as shown.
8
Assembly Instruction
STEP 9. Reflector Assembly
●Align the three pieces of the
Reflector as shown.
●Assemble using the three
Reflector Connecting Poles and 6
pcs 5/32” x 8mm screws. Insert the
Reflector Connecting Poles into the
curled edge of the reflector and align
the screw holes with the holes in the
Reflector. Insert and tighten the
screws.
STEP 10. Attach the Reflector
Plate
●3pcs 1/4” x 10mm screws, 3pcs
1/4” spring washer and 3pcs 1/4” flat
washer are needed for this assembly.
●Align the holes in the Reflector
Plate with those in the Reflector and
insert the screws from the underside
of the Reflector into the holes in the
Reflector Plate and tighten.
9
STEP 11. Attach the Reflector Nut &
Post
●Screw Threaded Ends Stud into the
Emitter top. Turn the Reflector Nut
onto the Stud and tighten.
●Place the Reflector Assembly and
Reflector Dome Cap through Threaded
Ends Stud onto the Emitter top.
Screws the Reflector Nut onto the
Reflector Dome Cap.
Assembly Instruction
STEP 12. Gas Tank Assembly
●Open the Tank door, fit the bottom
of the gas tank into the hole in the
bottom of the Tank Enclosure. Note
that the valve connection on the gas
tank should be facing directly towards
the door opening.
STEP 14. Secure Gas Tank
●Secure Gas Tank with the Tank Hook
by attaching to the Gas Tank Support,
as showed in diagram.
●Secure the other Regulator End onto
Gas Tank until tight.
●The LP-Gas supply cylinder must be
disconnected when this appliance is not
in use. Disconnect the gas tank by
turning the regulator counterclockwise.
CLOSE
g
OPEN
10
STEP 13. Tank hook assembly
z4pcs 3/16 x 12 mm screws, 4pcs 3/16 x
12 washer flat washer are needed for this
assembly
zThere are 4 screws used to attach the
tank hook, Align with the holes in the tank
hook, Insert the screws and then tighten
up the screws to assemble the tank hook
on the back panel support, as shown in
the diagram.
Inhaltsverzeichnis
Andere Nexgrill Terrassenheizung Handbücher
