Nexsan satabeast Bedienungsanleitung
This Quick Start Guide is intended to help you quickly get your unit unpacked, mounted, and
connected. For detailed instructions, see the SATABeast/SASBeast Installation and
Maintenance Manual or the Nexsan User Manual.
Quick Start Guide
1
//
Version 1.1
Taking Delivery
Upon receipt of your SATABeast/SASBeast, inspect the packaging for damage that may have been
sustained in transit. If there is visible damage on the packaging, contact your shipper before
proceeding.
Unpacking the Unit
Carefully unpack your SATABeast/SASBeast and inspect each item before installation:
1. Carefully cut the straps holding the box closed and remove the outer lid.
2. Remove the disk boxes, the accessory box, the inner rails, the padded envelope, the outer
packaging sleeve, and the top foam insert from the outer box.
3. Open the accessory box and padded envelope and make sure that all expected contents are
present. The accessory box/padded envelope should contain:
• rack-mounting hardware: four (4) side rail assemblies, two left and two right; two (2) front
mounting brackets, one left and one right; two (2) adjustable rear mounting brackets, one left and
one right; twenty (20) mounting rail assembly screws; sixteen (16) screws for securing the
assembled rails to the rack; twenty (20) screws for securing the side rails to the chassis; four (4)
rack bolts and four (4) cage nuts for securing the SATABeast/SASBeast to the rack
• other accessories: two (2) power cables; disposable ESD strap; null-modem cable; disk-
extraction handle; any additional items that may have been ordered, such as SAS cables or
Fibre Channel cables
4. Open the disk boxes and make sure that the proper number of disk drives is included.
5. With the help of a second person, carefully lift the SATABeast/SASBeast unit out of the packaging.
The packaging that the unit ships in is reusable and should be retained for future re-shipment. Be sure
to keep all packaging components.
Before You Begin
Required Tools and Equipment
To perform the installation, you will need the following tools and equipment:
• a suitable equipment rack (1,200mm deep recommended) with sufficient load capacity to hold the
SATABeast/SASBeast
• a size P1 Phillips-head screwdriver
• enough CAT6 Ethernet cable to connect the SATABeast to the local area network (LAN)
• enough CAT6 Ethernet cable, fibre-optic cable, or twisted-pair copper cable to connect the
SATABeast to the storage area network (SAN)
Prepare the Site
Before installing the SATABeast/SASBeast, prepare the installation site and rack. See Safety
Information for critical site and rack preparation information.
2
Prepare the Unit
Remove the PSUs and RAID Controllers from the unit:
1. Unscrew the retaining bolt, pull the lever to disengage the PSU, then slide the PSU out of its slot. Be
sure to support the PSU’s weight while removing it.
2. Unscrew both retaining bolts and pull both levers to disengage the RAID Controller. Slide the RAID
Controller out of its slot. Be sure to support the RAID Controller’s weight while removing it.
3. Label the controllers “Top” and “Bottom” before setting them aside.
Prepare the Mounting Rails
1. For each side mounting rail assembly, separate the inner and outer rails.
2. Attach the outer rails to the mounting brackets.
3. Loosely attach the rear mounting brackets to the rail assemblies, making sure that the rear bracket
can still move freely.
3
4. Attach each rail to the rack, then insert the cage nuts above and below each rail.
Mount the Unit
1. Attach the inner rails to each side of the chassis. The latch should be closer to the rear of the unit.
2. With the help of another person, lift the chassis, carefully line up the inner rails with the rack rails,
and slide the chassis into the rack.
Restore the Rear Modules
1. RAID Controllers: Slide the RAID Controller into its slot. For the bottom unit, be careful to not snag
the cables in the blower unit below.
Push in the latch levers to seat it, then tighten the retaining bolts.
4
2. PSUs: Slide the PSU into its slot, push the latch handle in to seat it, then tighten the retining bolt.
NOTE: Do not connect the power cords to the PSUs at this time.
Load Disk Drives
1. Pull the unit forward until there is enough room to remove the top cover.
2. Unscrew the retaining screws for the front panel (one on each side), then pull the front panel down.
3. Open the drive drawer lid.
4. Starting at the front of the drawer, and using the drive guides to help you orient the disks, carefully
load each disk drive into a drive slot. Make sure that each disk is fully seated and that the drive
ejection handles are flat against each drive.
5. Replace the top cover, close the front face, and replace the front panel retaining screws.
6. Slide the unit back into the rack.
7. Using the supplied bolts, bolt the face of the SATABeast/SASBeast unit to the rack.
CAUTION: Always load disk drives in rows of fourteen. Leaving large gaps between
disk drives decreases cooling efficiency and may result in some disk drives
overheating.
5
Attach Cables
Connect all necessary communication cables (Fibre Channel, Ethernet, expansion, serial) to the
appropriate connectors on the RAID Controller. See the Nexsan SATABeast/SASBeast/SATABeast Xi
Installation and Maintenance Manual.
Apply Power and Turn On
Using the two supplied power cords, connect each PSU to main power, making sure to fold down the
retaining clip over each one. Then turn the unit on by switching each PSU’s power switch to the on (|)
position.
Register and Configure the Unit
The Nexsan Product ID is located on the bottom left of the rear panel. Go to http://register.nexsan.com
to register your product.
Once the unit has finished booting up, follow the instructions in Chapter 1, Basic Setup of the Nexsan
User Manual to get your SATABeast/SASBeast system up and running.
Serial
Port
Ethernet
Ports
Fibre
Channel Ports
Expansion
Ports
Part number: P0450055
Release Date: January 2012
Version: 1.1
Copyright © 2011–2012 Nexsan Corporation. All Rights Reserved. Nexsan®, SATABeast®, SASBeast™, and the Nexsan logo are trademarks or
registered trademarks of Nexsan Corporation. All other trademarks and registered trademarks are the property of their respective owners.
Technical Support
By Phone:
U.S. & Canada: 866.2.NEXSAN (866-263-9726) or 760.690.1111
Europe, Middle East, Africa: +44 (0) 1332 291600
Japan: +81 3 5449 7590
By Email: support@nexsan.com
By Web: http://www.nexsan.com/support/service-request.aspx
NEXSAN 1445 Lawrence Drive, Thousand Oaks, CA 91320 | p. 866.4.NEXSAN | www.nexsan.com
Safety Information
CAUTION: When removing the SATABeast or SASBeast from the packaging, DO NOT
lift the unit by the handles on the front of the chassis. Doing so may cause damage to
the chassis or to internal components, or both. Lift the unit ONLY by the bottom edges
of the chassis, using safe lifting practices.
CAUTION: Ensure that the ambient temperature at the installation site is between 5°C
(41°F) and 35°C (95°F). If the temperature at the site is not actively regulated, ensure
that daily and seasonal temperature changes will not result in the ambient temperature
going outside these limits.
CAUTION: Always fully stabilize racks with wall anchors or stabilizing legs, or both,
before mounting the SATABeast/SASBeast, or any other components on the rack.
CAUTION: Situate the rack so that full air flow at both the front and the rear of the
SATABeast/SASBeast is possible.
CAUTION: Ensure that the floor beneath the mounting rack has enough load-bearing
capacity to support the rack and all mounted components.
CAUTION: Always fully secure all rack-mounting hardware when installing the
SATABeast/SASBeast in a rack. Insufficient rack-mount support may allow the unit to
fall onto other rack-mounted hardware or onto the floor, potentially damaging
equipment or causing injury to nearby personnel.
CAUTION: When applying power to the SATABeast/SASBeast, use ONLY the IEC
power cords originally supplied with the unit. Do NOT use other power cords, even if
they appear identical to the supplied cords.
CAUTION: The SATABeast/SASBeast unit is heavy and requires two people to lift it
and slide it onto the mounting rails. Do NOT attempt to mount the unit onto the
mounting rails by yourself.
CAUTION: Computer components and disk drives are sensitive to electrostatic
discharge (ESD). Be sure to ground any electrostatic charge from your person before
touching components with your hands or with any tools. While installing the unit, use
the anti-static wrist-strap shipped with the unit.
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Nexsan Lagerung Handbücher
Nexsan
Nexsan E Series Bedienungsanleitung
Nexsan
Nexsan BEAST BT60 Bedienungsanleitung
Nexsan
Nexsan UNITY224X Bedienungsanleitung
Nexsan
Nexsan SATAboy Series Bedienungsanleitung
Nexsan
Nexsan UNITY7900 Bedienungsanleitung
Nexsan
Nexsan BEAST Series Bedienungsanleitung
Nexsan
Nexsan NST2000 Bedienungsanleitung
Nexsan
Nexsan US316 Bedienungsanleitung
Nexsan
Nexsan E Series Bedienungsanleitung
Nexsan
Nexsan Nexsan Unity Betriebsanleitung
Nexsan
Nexsan E Series Bedienungsanleitung
Nexsan
Nexsan BEAST BT60 Bedienungsanleitung
Nexsan
Nexsan UNITY2000 Bedienungsanleitung
Nexsan
Nexsan Unity2200 Bedienungsanleitung
Nexsan
Nexsan Unity 2200 Bedienungs- und Wartungshandbuch
Nexsan
Nexsan UNITY3300 Bedienungsanleitung
Nexsan
Nexsan Unity 2200 Bedienungsanleitung
Nexsan
Nexsan Unity 2200 Bedienungsanleitung
Nexsan
Nexsan UNITY5000 Bedienungs- und Wartungshandbuch
Nexsan
Nexsan Unity 4400 Bedienungsanleitung
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung