Next Level Racing ELITE Series Bedienungsanleitung

Video Instruction: bit.ly/nlrbuild

INSTRUCTION MANUAL

TAKE RACING TO THE NEXT LEVEL®

ELITE SERIES

DIRECT MOUNT

MONITOR STAND

2 3

support@nextlevelracing.com Video Instruction: bit.ly/nlrbuild

YOUR

SIM RACING

JOURNEY

STARTS

HERE

We know you’re eager to start racing! Take your time with the

instructions and follow this guide to assemble your product.

You’ll be setting yourself up for success with following the

instruction booklet to fully optimize your product.

TAKE RACING

TO THE NEXT LEVEL®

NEXTLEVELRACING.COM

@nextlevelracingOcial

@next_level_racing

@nextlvlracing

Next Level Racing

support@nextlevelracing.com

ASSEMBLY

VIDEO

bit.ly/nlrbuild

4 5

support@nextlevelracing.com Video Instruction: bit.ly/nlrbuild

WARNING

PRE-RACE

CHECKS IN THE

BOX

If you require any support with your product please contact our friendly

team at: support@nextlevelracing.com

*NOT TO SCALE

SINGLE DIRECT

MONITOR STAND

MAIN UPRIGHTS

3 x END CAPS (40 x 80 ANGLED)4 x CABLE CLIPS

5 x END CAPS (40 x 40) 3 x END CAPS (40 x 80)

1 x SMALL VESA PLATE

1 x LARGE VESA PLATE

4 x M4 15mm BOLTS

4 x M5 15mm BOLTS

4 x M6 15mm BOLTS

38 x M8 16mm BOLTS

2 x M8 40mm BOLTS

2 x M8 60mm BOLTS

4 x M4 15mm BOLTS

4 x M5 15mm BOLTS

4 x M6 15mm BOLTS

44 x M8 16mm BOLTS

MAIN CROSS BAR

OUTRIGGER ARMS

ALLEN KEYS

38 x FULL WIDTH T-NUTS 8 x REGULAR T-NUTS

4 x 16mm COUNTERSUNK BOLTS

4 x UPRIGHT MOUNTING BRACKETS

1 x VESA MOUNTING BRACKET

2 x MOUNTING PLATES

2 x CORNER BRACKETS

SPANNER WRENCH

2 x M8 FLANGE NUTS

4 x M6 FLANGE NUTS

• Please do not use power tools for assembly as over tightening can damage parts.

• If in doubt consult the installation video or contact us on support@nextlevelracing.com

• T-Nuts can not be installed mid channel. Must be installed from the ends of extrusion.

• Plan the placement of cable management clips at the start of your build.

• Please ensure T-Nuts are correctly placed within the extrusion.

• Lay out and build on a level surface.

• Do not hang additional loads on monitor stand.

• Beware of sharp edges on extrusion pieces.

• Do not force parts together.

• Avoid cross threading bolts.

ALUMINIUM EXTRUSION TIPS

• Please do not use power tools for assembly as over tightening can damage your frame.

• Please ensure T-Nuts are correctly placed within the extrusion.

• Beware of sharp edges on the extrusion pieces.

• Do not force parts together.

• Avoid cross threading bolts.

WARNING

CHOKING HAZARD - Small parts not for children under 3 years

or any individuals who have a tendency to place inedible objects

in their mouths.

ASSEMBLY

VIDEO

bit.ly/nlrbuild

L) (R

NOTE: Some Items Come with Rust Resistant Coating

6 7

support@nextlevelracing.com Video Instruction: bit.ly/nlrbuild

IN THE

BOX *NOT TO SCALE

OVERHEAD DIRECT

MONITOR STAND

OVERHEAD ANGLE ARMS

2 x CABLE CLIPS

9 x END CAPS (40 x 40)

1 x SMALL VESA PLATE

ALLEN KEYS

14 x FULL WIDTH T-SLOT NUTS

2 x OVERHEAD ANGLE BRACKETS 1 x VESA MOUNTING BRACKET

2 x MOUNTING PLATES

SPANNER WRENCH

2 x M8 FLANGE NUTS

OVERHEAD UPRIGHTS

OVERHEAD CROSS BAR

TABLE OF CONTENTS

SINGLE DIRECT MOUNT

MONITOR STAND:

PAGES: 08 - 16

OVERHEAD DIRECT MOUNT

MONITOR STAND:

PAGES: 16 - 23

4 x M4 15mm BOLTS

4 x M5 15mm BOLTS

4 x M6 15mm BOLTS

14 x M8 16mm BOLTS

8 x M8 40mm BOLTS

4 x M4 15mm BOLTS

4 x M5 15mm BOLTS

4 x M6 15mm BOLTS

24 x M8 16mm BOLTS

R) (LR) (L

NOTE: Some Items Come with

Rust Resistant Coating

PARTS:

•

• 4 x T-NUTS

FGT ELITE COCKPIT

GTELITE COCKPIT

PARTS:

•

• NIL

04 Re-Install the Wheel Plate previously uninstalled in STEP 01. Skip to STEP 07.

PARTS:

•

• 8 x T-NUTS

FGT ELITE COCKPIT

GTELITE COCKPIT

02 Install 4 x T-Nuts into the inside channel of both Vertical Posts. Repeat for the other side.

PARTS:

•

• NIL

01 A) Uninstall the Bolts securing the Wheel Plate to the Vertical Posts and remove the Wheel Plate.

B) Slide down the T-Nuts that were securing the Wheel Plate.

support@nextlevelracing.com Video Instruction: bit.ly/nlrbuild

05 Install 4 x T-Nuts into the inside channel of the Left Vertical Post and slide them down using the

provided Allen key.

FRONT AND SIDE MOUNT

COCKPIT SETUP SKIP

TO STEP # 05

WHEEL DECK SETUP

NOTE: Install T-Slot Nuts suited for

your cockpit extrusion proﬁle.

NOTE: Install T-Nuts suited for

your cockpit extrusion proﬁle.

FRONT/SIDE MOUNT SETUP

SKIP TO STEP 07

Repeat

on Other

Side

PARTS:

•

• NIL

03 Slide the T-Nuts in the Vertical Post to the locations shown above and repeat for the other

Vertical Post.

WHEEL DECK T-NUT LOCATION

(VERTICAL POST INSIDE)

MOUNTING PLATES T-NUT LOCATION

(VERTICAL POST INSIDE)

Repeat

on Other

Side

A)B)

support@nextlevelracing.com Video Instruction: bit.ly/nlrbuild

PARTS:

•

• 8 x T-NUTS

08 Install 2 x T-Nuts into the top channel of both the inside and outside of the Left Outrigger Arm. Repeat

for the Right Outrigger Arm.

PARTS:

•

• 4 x T-NUTS

06 Install 4 x T-Nuts into the inside channels of the Right Vertical Post and slide them down using the

provided Allen key.

PARTS:

•

• 8 x M8 16mm BOLTS

•

• 8 x M8 WASHERS

10 A) Align the Outrigger Arm assembly with the T-Nuts previously installed in STEP 02 or STEP 06.

B) Bolt through and secure with 4 x M8 Bolts and Washers. Repeat on the other side.

PARTS:

•

• 2 x MOUNTING PLATES

•

• 4 x M8 16mm BOLTS

•

• 4 x M8 WASHERS

•

• 4 x M8 COUNTERSUNK BOLTS

09 A) Align the holes on the Mounting Plates with the T-Nuts previously installed in STEP 07

B) Bolt through and secure with 2 x M8 Countersunk Bolts and 2 x M8 Bolts. Repeat on the other side.

PARTS:

•

• 8 x T-NUTS

A) Install 4 x T-Nuts into the outside channels of the Left Outrigger Arm.

B) Install 4 x T-Nuts into the outside channels of the Right Outrigger Arm.

10 11

FRONT/SIDE MOUNT SETUP

INSIDE

A)B)

OUTSIDE

Repeat

on Other

Side

(MITERED EDGE)

(MITERED EDGE)Repeat

on Other

Side

A)B)

(Location For Countersunk Bolts)

(MITERED EDGE)

PARTS:

•

• 4 x UPRIGHT MOUNTING

BRACKETS

•

• 8 x M8 16mm BOLTS

•

• 8 x M8 WASHERS

11 A) Align the holes on the Upright Mounting Brackets with the T-Nuts previously installed in STEP 08.

B) Bolt through and secure with 4 x M8 Bolts and Washers. Repeat on the other side.

Repeat

on Other

Side

A)B)

Repeat

on Other

Side

support@nextlevelracing.com Video Instruction: bit.ly/nlrbuild

PARTS:

•

• 6 x T-NUTS

•

• 1 x MAIN CROSS BAR

14 A) Install 4 x T-Nuts into the back channel of the Main Cross Member.

B) Install 1 x T-Nut into the top and bottom channels of the Main Cross Member.

PARTS:

•

• 2 x MAIN UPRIGHTS

•

• 2 x M8 60mm BOLTS

•

• 2 x M8 WASHERS

•

• 2 x M8 FLANGE NUTS

13a Align the through hole on the Main Uprights with the holes on the Mounting Vertical Plates previously

installed in STEP 11. Bolt through and secure with M8 Bolts, Washers and Flange Nuts.

PARTS:

•

• 2 x CORNER BRACKETS

•

• 6 x M8 16mm BOLTS

•

• 6 x M8 WASHERS

16 Align the holes on the Corner Bracket with the T-Nuts previously installed in STEP 12 & STEP 14(A),

bolt through and secure with M8 Bolts and Washers. Repeat on the other side.

PARTS:

•

• 8 x T-NUTS

•

• 2 x MAIN UPRIGHTS

12 Install 1 x T-Nut into the inside and front channel of the Main Uprights. Install 2 x T-Nuts into the

outside channel. Repeat on the other side.

PARTS:

•

• 1 x MAIN CROSS BAR

•

• 2 x M8 40mm BOLTS

•

• 2 x M8 WASHERS

15 A) Align the through holes on the Main Cross Member with the T-Nuts previously installed in STEP 12.

B) Bolt through and secure with M8 Bolts and Washers.

PARTS:

•

• 4 x M8 16mm BOLTS

•

• 4 x M8 WASHERS

12 13

INSIDE FRONT OUTSIDE

Repeat

on Other

Main

Upright

BACK

TOP

BOTTOM

A)B)

(OUTSIDE)

13b Align the T-Nuts previously installed into the Main Uprights in STEP 12 with the holes on the Mounting

Vertical Plates. Bolt through and secure with M8 Bolts and Washers.

(MOUNTING HOLE)

Note: For easier installation hand

screw M8 bolt in to T-Nut to assist

sliding T-Nut in to channel.

(MOUNTING HOLE)

PARTS:

•

• 1 x LARGE VESA PLATE

•

• 1 x SMALL VESA PLATE

•

• 4 x M6 FLANGE NUTS

17b A) Align the pressed studs on the Large Vesa Plate with the holes on the Small Vesa Plate.

B) Secure with M6 Flange Nuts.

PARTS:

•

• 1 x VESA MOUNTING BRACKET

•

• 1 x SMALL VESA PLATE

•

• 4 x M8 16mm BOLTS

•

• 4 x M8 WASHERS

17a A) Align the holes on the Vesa Mounting Bracket with the threaded holes on the Small Vesa Plate.

B) Bolt through and secure with M8 Bolts and Washers.

PARTS:

•

• 2 x M8 16mm BOLTS

•

• 2 x M8 WASHERS

19 Align the Vesa assembly with T-Nuts previously installed in STEP 14. Bolt through and secure with M8

Bolts and Washers.

PARTS:

•

• NIL

20 Loosen the bolts securing the Small Vesa Plate to the Vesa Mounting Bracket. Adjust to your desired

angle and tighten the bolts to lock in place.

support@nextlevelracing.com

PARTS:

•

• 1 x VESA MOUNTING BRACKET

•

• 4 x M8 16mm BOLTS

•

• 4 x M8 WASHERS

18 A) Align the holes on the Vesa Mounting Bracket with the threaded holes on the Small Vesa Plate.

B) Bolt through and secure with M8 Bolts and Washers

Video Instruction: bit.ly/nlrbuild

PARTS:

•

• NIL

21 Loosen the bolts securing the Vertical Assembly to the Outrigger Arms. Adjust to your desired position

and tighten the bolts to lock in place.

OPTIONAL LARGE VESA MOUNT

(75mm X 75mm - 200mm X 200mm) ANGLE ADJUSTMENT RANGE

ADJUSTMENT RANGE

SMALL VESA MOUNT

(75mm X 75mm - 100mm X 100mm)

A)B)

support@nextlevelracing.com Video Instruction: bit.ly/nlrbuild

PARTS:

•

• 4 x T-NUTS

01 Install 2 x T-Nuts into inside channel of the Main Uprights. Repeat on the other side.

PARTS:

•

• 4 x END CAPS (40 x 40)

•

• 2 x END CAPS (40 x 80)

•

• 2 x END CAPS (40 x 80 ANGLED)

23 Install all End Caps.

PARTS:

•

• 2 x OVERHEAD UPRIGHTS

•

• 4 x T-NUTS

02 Install 2 x T-Nuts into the outer channel (side with alignment markings) of the Overhead Uprights.

Repeat on the other side.

PARTS:

•

• NIL

22 Loosen the bolts securing the Main Cross Member to the Main Uprights. Adjust to your desired height

and tighten the bolts to lock in place.

OVERHEAD DIRECT MONITOR

INSTALLATION

If you require further support with your product please

contact our friendly team at: support@nextlevelracing.com

16 17

HEIGHT ADJUSTMENT RANGE

OUTSIDE

Repeat

on Other

Side

A: Align end-cap to

corner of extrusion

B: Depress the centre

of the end-cap and align

the tab to the ﬁrst hole.

Then align second tab

with the second hole.

C: Finished end-cap

Repeat

on Other

Side

support@nextlevelracing.com

PARTS:

•

• 4 x M8 40mm BOLTS

•

• 4 x M8 WASHERS

03 Align the holes on the Overhead Uprights with T-Nuts previously installed in STEP 01. Bolt through and

secure with M8 Bolts and Washers. Repeat on the other side.

PARTS:

•

• 2 x OVERHEAD ANGLE BRACKETS

•

• 4 x M8 16mm BOLTS

•

• 4 x M8 WASHERS

04 Align the holes on the Overhead Angle Brackets with the T-Nuts previously installed in STEP 02. Bolt

through and secure with M8 Bolts and Washers.

PARTS:

•

• 2 x OVERHEAD ANGLE ARMS

•

• 2 x T-NUTS

05 Install 1 x T-Nut into the front and outside channel of the Overhead Angle Arm.

Repeat on the other side.

PARTS:

•

• 2 x M8 16mm BOLTS

•

• 2 x M8 WASHERS

06b Align the T-Nuts previously installed into the Overhead Angle Arms in STEP 05 with the curved slot on the Overhead Angle

Bracket. Bolt through and secure with an M8 Bolt and Washer. Repeat for the other Overhead Angle Arm.

PARTS:

•

• 2 x OVERHEAD ANGLE ARMS

•

• 2 x M8 60mm BOLTS

•

• 2 x M8 WASHERS

•

• 2 x M8 FLANGE NUTS

06a Align the through hole on the Overhead Angle Arm with the hole on the Overhead Angle Bracket. Bolt through

and secure with an M8 Bolt, Washer and Flange Nut. Repeat for the other Overhead Angle Arm.

PARTS:

•

• 1 x MAIN CROSS BAR

•

• 2 x M8 40mm BOLTS

•

• 2 x M8 WASHERS

07 Align the through holes on the Overhead Cross Bar with the T-Nuts previously installed in STEP 05.

Bolt through and secure with M8 Bolts and Washers.

Video Instruction: bit.ly/nlrbuild

18 19

OUTSIDE FRONT

Repeat

on Other

Side

Repeat

on Other

Side

(MOUNTING HOLE)

Andere Handbücher für ELITE Series

Inhaltsverzeichnis

Sprachen:

Andere Next Level Racing Rack & Stand Handbücher

Next Level Racing

Next Level Racing COMBAT FLIGHT KIT Bedienungsanleitung

Next Level Racing

Next Level Racing F-GT Bedienungsanleitung

Next Level Racing

Next Level Racing ELITE Series Bedienungsanleitung

Next Level Racing

Next Level Racing Wheel Stand DD Bedienungsanleitung

Next Level Racing

Next Level Racing CHALLENGER MONITOR STAND Bedienungsanleitung

Next Level Racing

Next Level Racing GT Lite Bedienungsanleitung

Next Level Racing

Next Level Racing FREE STANDING SINGLE MONITOR STAND Bedienungsanleitung

Next Level Racing

Next Level Racing F-GT Monitor Stand Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung