NF HVA4321 Bedienungsanleitung

INSTRUCTION MANUAL

NF Corporation

http://www.nfcorp.co.jp/

NF Corporation

6-3-20, Tsunashima-higashi, Kohoku-ku,Yokohama 223-8508 JAPAN

HVA4321

10kV AC/DC AMPLIFIER

HVA4321 10kV AC/DC AMPLIFIER

10kV AC/DC AMPLIFIER

HVA4321

Instruction Manual

DA00012063-001

This unit generates high voltage. Incorrect operation may result in death

or injury. To prevent death or injury, please read this manual carefully.

Keep this manual near the unit so that operators may read at any time.

HVA4321 i

！

⎯ Preface ⎯

Thank you for purchasing the 10 kV AC/DC amplifier.

To ensure safe and proper use of this electric equipment, please read first INSTRUCTIONS FOR SAFE

USE on the following pages.

 Caution Symbols Used in This Manual

The following caution symbols are used in this manual. Be sure to observe these caution symbols and their

contents to ensure the safety of the user and avoid damage to the equipment.

This mark indicates information for the avoidance of a hazard such as electric shock that may endanger

human life or cause injury during handling of the equipment.

This mark indicates information for the avoidance of damage to the equipment during handling.

This manual has the following chapter organization.

If reading this manual for the first time, start from Chapter 1.

1. OVERVIEW

Describes various items that must be checked prior to using this product.

2. PREPARATIONS BEFORE USE

Describes various cautions regarding preparations to be made before installation or operation.

3. PART NAMES AND FUNCTIONS

Describes functions, movements and basic operations for knobs on the panel. Read this manual

while operating the unit.

4. OPERATION

Describes operation of this product.

5. REPRESENTATIVE CHARACTERISTICS

Describes representative characteristic of this product.

6. TROUBLESHOOTING

Describes corrective actions when problems occur.

7. MAINTENANCE

Describes basic operation tests and daily maintenance procedures.

8. SPECIFICATIONS

Lists the specifications (functions and performance).

！CAUTION

WARNING

HVA4321 ii

⎯Safety Precautions ⎯

To ensure safe use, be sure to observe the following warnings and cautions.

NF Corporation shall not be held liable for damages that arise from a failure to observe these warnings and

cautions.

This product is a Class 1 product (with protective conductor terminal) that conforms to the JIS and IEC

insulation standards.

Be sure to observe the contents of this instruction manual.

This instruction manual contains information for the safe operation and use of this product.

Be sure to read this information first before using this product.

All the warnings in the instruction manual must be heeded to prevent hazards that may cause major

accidents.

Be sure to ground the product.

This product uses a line filter and must be grounded to avoid the risk of electric shock.

To prevent electric shock, be sure to safely implement grounding according to Japanese Standard for

Electrical Equipment Technology D (Type 3) or higher.

When the 3-pin power plug is connected to the 3-pin power outlet with protective ground contact, this

product is automatically grounded.

To use 3-pin 2-pin conversion adapter, be sure to connect the ground line (green) of the conversion

adapter to the ground terminal near the outlet.

If the ground terminal is available at the back panel, the terminal may be grounded with a wire equivalent

to or larger than the thickness of the power cable.

Check the power supply voltage.

This product operates on the power supply voltage indicated in Grounding and Power Supply Connection

in this instruction manual.

Prior to connecting the power supply, check that the voltage of the power supply matches the rated power

supply of the product.

Observe the fuse rating.

Fire may occur. Use the rated fuse specified in Grounding and Power Supply Connection in the

instruction manual.

When the fuse is replaced, be sure to disconnect the power cable from the outlet.

In case of suspected anomaly

If this product emits smoke, an abnormal smell, or abnormal noise, immediately disconnect the power

cable and stop operation.

If such an anomaly occurs, do not use this product until it has been repaired, and immediately report the

problem to the location of purchase (either NF Corporation or your distributor).

Do not use this product when gas is present.

Otherwise, it may cause an explosion.

HVA4321 iii

！

Do not remove the cover.

This product contains high-voltage parts. Absolutely never remove its cover. Even when the inside of this

product needs to be inspected, do not touch the inside.

All such inspections are to be performed by service technicians designated by NF Corporation.

Do not modify this product.

Absolutely never modify this product, as this may cause new hazards and may disqualify this product

from repair in case of failure.

Safety-related symbols

The general definitions of the safety-related symbols used on this product and in the instruction manual

are provided below.

Instruction manual reference symbol

This symbol is displayed to alert the user to potential danger and refer him/her to

the instruction manual.

Electric shock danger symbol

This symbol indicates locations that present a risk of electric shock under specific

conditions.

Protective terminal grounding symbol

This symbol indicates terminals that require grounding to prevent electric shock.

Before operation of the unit, be sure to connect this terminal to the ground of type

3 or higher. (When the 3-pin power cable is connected to the 3-pin outlet, it is not

necessary to connect this ground terminal.)

Warning Symbol

This symbol indicates information for avoiding danger to human life or bodily

injury such as electric shock while handling this product.

Caution Symbol

This symbol indicates information for preventing damage to the product when

handling it.

Other symbols

This symbol indicates the "ON" position of the power switch.

This symbol indicates the "OFF" position of the power switch.

This symbol indicates that the external conductor of the connector is connected to the

case.

This symbol indicates that the external conductor of the connector is connected to the

signal ground.

CAUTION

WARNING

HVA4321 iv

HVA4321 v

Contents

Page

1. Overview

1.1 Features................................................................................................................. 1-1

1.2 Function description and block diagram ............................................................ 1-3

1.2.1 Function description .................................................................................................... 1-3

1.2.2 Block diagram............................................................................................................... 1-4

Preparations before use

2.1 Before using the HVA4321.................................................................................... 2-1

2.2 Installation............................................................................................................. 2-2

2.3 Grounding and power supply connection........................................................... 2-3

3. Nomenclature and functions

3.1 Signal system........................................................................................................ 3-1

3.1.1 Internal DC bias signal source..................................................................................... 3-1

3.1.2 External bias signal input ............................................................................................ 3-1

3.1.3 External signal input .................................................................................................... 3-2

3.1.4 Input signal ON/OFF ..................................................................................................... 3-2

3.2 Amplifier ................................................................................................................ 3-4

3.2.1 Amplifier operation mode ............................................................................................ 3-4

3.2.2 Amplifier control........................................................................................................... 3-6

3.2.3 Output ........................................................................................................................... 3-9

3.3 Monitor and control signal system .................................................................... 3-11

3.3.1 Monitor .........................................................................................................................3-11

3.3.2 Control signal system ................................................................................................ 3-12

3.4 Power supply items ............................................................................................ 3-17

3.5 Panel drawing ..................................................................................................... 3-18

3.5.1 Front panel.................................................................................................................. 3-18

3.5.2 Rear panel ................................................................................................................... 3-19

4. Operation method

4.1 Operation example in constant voltage mode .................................................... 4-1

4.1.1 Panel setting ................................................................................................................. 4-3

4.1.2 Connection of signal source and connection of load................................................. 4-6

4.1.3 Power supply and internal high voltage DC power supply......................................... 4-9

4.1.4 Signal output and adjustment.....................................................................................4-11

4.1.5 Signal OFF .................................................................................................................. 4-13

4.2 Operation example in constant current mode (total) ....................................... 4-14

4.2.1 Panel setting ............................................................................................................... 4-16

4.2.2 Connection of signal source and connection of load............................................... 4-19

4.2.3 Power supply and internal high voltage DC power supply....................................... 4-22

4.2.4 Signal output and adjustment.................................................................................... 4-24

4.2.5 Signal OFF .................................................................................................................. 4-26

Contents

HVA4321 vi

4.3 Operation example in constant current mode (load)........................................ 4-27

4.3.1 Panel setting ............................................................................................................... 4-29

4.3.2 Connection of signal source and connection of load............................................... 4-32

4.3.3 Power supply and internal high voltage DC power supply....................................... 4-35

4.3.4 Signal output and adjustment.................................................................................... 4-37

4.3.5 Signal OFF .................................................................................................................. 4-39

4.4 Operation example in constant current + constant voltage mode .................. 4-40

4.4.1 Panel setting ............................................................................................................... 4-42

4.4.2 Connection of signal source and connection of load............................................... 4-45

4.4.3 Power supply and internal high voltage DC power supply....................................... 4-48

4.4.4 Signal output and adjustment.................................................................................... 4-50

4.4.5 Signal OFF .................................................................................................................. 4-52

4.5 Change of load and power OFF ......................................................................... 4-53

4.5.1 Change of load ........................................................................................................... 4-53

4.5.2 Power supply OFF ...................................................................................................... 4-56

4.6 Remote control.................................................................................................... 4-57

4.6.1 Remote control ........................................................................................................... 4-57

4.6.2 Panel setting for use of remote control..................................................................... 4-58

5. Representative characteristics

5.1 Measuring method ................................................................................................ 5-1

5.2 Characteristics in constant voltage mode .......................................................... 5-3

5.2.1 Frequency characteristics ........................................................................................... 5-3

5.2.2 Step response............................................................................................................... 5-4

5.3 Characteristics in constant current mode .......................................................... 5-5

5.3.1 Frequency characteristics ........................................................................................... 5-5

5.3.2 Step response............................................................................................................... 5-6

5.4 Characteristics in constant current and constant voltage mode ...................... 5-7

5.4.1 Frequency characteristics ........................................................................................... 5-7

5.5 Characteristics of voltage monitor and current monitor ................................... 5-8

5.5.1 Frequency characteristics ........................................................................................... 5-8

5.6 Others .................................................................................................................... 5-9

5.6.1 Delay of output signal for input signal........................................................................ 5-9

5.6.2 Step response due to difference of amplitude .......................................................... 5-10

6. Troubleshooting

6.1 When suspecting a fault....................................................................................... 6-1

7. Maintenance

7.1 Daily maintenance ................................................................................................ 7-1

7.2 Inspection.............................................................................................................. 7-2

7.3 When the unit is not used for a long time........................................................... 7-2

7.4 Performance test................................................................................................... 7-3

7.4.1 Test of constant voltage mode..................................................................................... 7-3

7.4.2 Test of constant current mode..................................................................................... 7-4

Inhaltsverzeichnis

Andere NF Verstärker Handbücher

NF SA-230F5 Bedienungsanleitung

NF BA4825 Bedienungsanleitung

NF HSA42051 Bedienungsanleitung

NF CA5351 Bedienungsanleitung

NF CA5360 Bedienungsanleitung

NF SA-420F5 Bedienungsanleitung

NF HSA42012 Bedienungsanleitung

NF SA-220F5 Bedienungsanleitung

NF SA-430F5 Bedienungsanleitung

NF CA5350 Bedienungsanleitung

NF SA-200F3 Bedienungsanleitung

NF SA-421F5 Bedienungsanleitung

NF HSA4012 Bedienungsanleitung

NF HSA42011 Bedienungsanleitung

NF IV-202F4 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung