NI REM-11152 Bedienungsanleitung

(217) 352-9330 | [email protected] | artisantg.com

ARTISAN

TECHNOLOGY

GROUP

Your definitive source

for

quality

pre-owned

equipment.

Artisan Technology

Group

Full-service,

independent

repair

center

with

experienced

engineers

and

technicians

on staff.

buy

your

excess,

underutilized,

and

idle

equipment

along

with

credit

for

buybacks

and

trade-ins

Custom

engineering

your

equipment

works

exactly as

you

specify.

•

Critical

and

expedited

services

•

Leasing

Rentals/

Demos

• In

stock/

Ready-to-ship

•

!TAR-certified

secure

asset

solutions

Expert

team

ITrust

guarantee

100%

satisfaction

All

ademarks,

names, a

s a

earing here

are

e property of

pecti

ner

Visit our website - Click HERE

GETTING STARTED GUIDE

NI REM-11152

Digital Input Module for Remote I/O

This document explains how to connect to the REM-11152.

Note The guidelines in this document are specific to the REM-11152. The other

components in the system might not meet the same safety ratings. Refer to the

documentation for each component in the system to determine the safety and EMC

ratings for the entire system.

Caution Do not operate the REM-11152 in a manner not specified in this

document. Product misuse can result in a hazard. You can compromise the safety

protection built into the product if the product is damaged in any way. If the product

is damaged, return it to NI for repair.

Isolation Withstand Voltages

Test section Test voltage

5 V communications power (logic), 24 V supply (I/O) 500 VAC, 50 Hz, 1 min.

5 V supply (logic)/functional earth ground 500 VAC, 50 Hz, 1 min.

24 V supply (I/O)/functional earth ground 500 VAC, 50 Hz, 1 min.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits provide reasonable protection against harmful interference when the product is

operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved by National

Instruments could void your authority to operate it under your local regulatory rules.

Preparing the Environment

Ensure that the environment in which you are using the REM-11152 meets the following

specifications.

Operating temperature -25 °C to 60 °C

Operating humidity 5% RH to 95% RH, noncondensing

Pollution Degree 2

Maximum altitude 3,000 m

Indoor use only.

Note Refer to the device datasheet on ni.com/manuals for complete specifications.

2| ni.com | REM-11152 Getting Started Guide

Verifying the Kit Contents

Verify that the following items are included in the REM-11152 kit.

Figure 1. REM-11152 Kit Contents

12 3 4

1. NI REM-11152

2. Bus connector

3. Supply voltage connector

4. Spring-terminal block (x8)

Unpacking the Kit

Caution To prevent electrostatic discharge (ESD) from damaging the device,

ground yourself using a grounding strap or by holding a grounded object, such as

your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the device from the package and inspect the device for loose components or any

other sign of damage.

Caution Never touch the exposed pins of connectors.

Note Do not install a device if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

REM-11152 Getting Started Guide | © National Instruments | 3

Installing the REM-11152

Figure 2. Structure of the REM-11152

1. Bus connector

2. REM-11152

3. Module function label

4. Supply voltage connector

5. Spring-terminal block

6. LED indicators

Table 1. Module Function Labels

Label Color Module Function

Blue Digital input

Red Digital output

Green Analog input, thermocouple

Yellow Analog output

White Bus coupler, power module

Installing Bus Connectors

What to Use

• Bus connector

• DIN rail

What to Do

Complete the following steps to install bus connectors on the DIN rail.

4| ni.com | REM-11152 Getting Started Guide

1. Insert the bus connector for the REM-11152 into the DIN rail.

Caution Verify that you are using the correct bus connector for the module

width.

2. Slide the bus connector along the DIN rail until it connects to the preceding bus

connector.

Note A bus connector will not attach to a preceding bus connector with a

mounted module. Remove the preceding module before installing additional

bus connectors.

3. Repeat Steps 2 and 3 for additional bus connectors.

Installing the Module

What to Use

• REM-11152

• Mounted bus connector

What to Do

Complete the following steps to install the REM-11152 on the DIN rail.

REM-11152 Getting Started Guide | © National Instruments | 5

1. Align the REM-11152 over the appropriate bus connector.

Note Verify that the bus connector socket aligns with the socket on the

underside of the module.

2. Press the REM-11152 directly onto the bus connector and DIN rail until it clicks into

place.

Caution Tilting the module when mounting it on the DIN rail will damage the

contacts.

Installing Spring-Terminal Blocks

What to Use

• REM-11152

• Spring-terminal block

What to Do

Align the spring-terminal block over the REM-11152 and press until it clicks into place.

6| ni.com | REM-11152 Getting Started Guide

REM-11152 Pinout

DI0 to DI7

24 VDC

GND

DI8 to DI15

24 VDC

GND

24 VDC

GND

Table 2. REM-11152 Signal Descriptions

Signal Color Description

a1, a2 Red 24 VDC (UI) Supply to digital input modules (internally

jumpered)

b1, b2 Blue GND Reference potential of the supply voltage

(internally jumpered)

00 to 07 Orange DI0...DI7 Digital inputs 0 to 7

40 to 47 Orange DI8...DI15 Digital inputs 8 to 15

10 to 17, 50 to 57 Red 24 VDC (US) Sensor supply voltage output

REM-11152 Getting Started Guide | © National Instruments | 7

Table 2. REM-11152 Signal Descriptions (Continued)

Signal Color Description

20 to 27, 60 to 67 Blue GND Reference potential for all channels

30 to 37, 70 to 77 Green FE Functional earth ground (FE)

Figure 3. REM-11152 LEDs

00 02 04 06

10 12 14 1611 13 15 17

20 22 24 2621 23 25 27

41 43 45 47

51 53 55 57

61 63 65 67

71 73 75 77

40 42 44 46

50 52 54 56

60 62 64 66

70 72 74 76

32 34 3631 33 35 37

01 03 05 07

Table 3. LED Indicators

LED LED Color LED Pattern Indication

Green

Solid The REM-11152 is ready for operation.

Flashing Data is invalid or unavailable.

Green/Yellow Flashing The REM-11152 cannot communicate with

the connected devices.

Yellow

Solid The REM-11152 did not detect a valid cycle

after power-on.

Flashing The REM-11152 is not part of the

configuration.

Red

Solid The REM-11152 has lost connection to the

Bus Coupler.

Flashing The REM-11152 has lost connection to the

preceding adjacent module.

— Off The REM-11152 is in reset mode.

Green Solid Supply to digital output module present.

— Off No supply to digital output modules.

8| ni.com | REM-11152 Getting Started Guide

Table 3. LED Indicators (Continued)

LED LED Color LED Pattern Indication

Red Solid Breakdown or overload/short-circuit of an

output.

— Off No I/O error.

Red Solid Breakdown or overload/short-circuit of an

output.

— Off No I/O error.

00 to 07, 40 to

Red Solid Short-circuit/overload of the output.

Yellow Solid Input is set.

— Off Input is not set.

Connecting the REM-11152

24 VDC

DI (0:7)

US(24 V)

GND

REM-11152

GND

US(24 V)

DI (8:15)

–

Sourcing-Output

Device

Sourcing-Output

Device

GND

24 V

GND

• The input signals connect to the DI terminals.

• GND provides a path for the return current to flow.

• US and FE are optional, device-dependent connections.

Inhaltsverzeichnis

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung