NI CB-68LP Bedienungsanleitung

USER GUIDE

NI CB-68LP/CB-68LPR

Unshielded 68-Pin Screw Terminal Connector Block Accessories

The National Instruments CB-68LP and CB-68LPR are unshielded I/O accessories with

68 screw terminals for easy signal connection to a National Instruments 68-pin DAQ device.

Caution The CB-68LP/CB-68LPR accessory must be installed inside a suitable

enclosure prior to use.

Caution Before using this unshielded accessory, determine if the documentation

fortheconnecteddevicerequiresshieldedcablesoraccessoriestoensureitsspecified

EMC performance. If the connected device requires shielded cables or accessories,

do not use this product unless it is installed in a shielded enclosure with properly

designed and shielded input/output ports and connected to the NI product using a

shielded cable.

Figure 1. CB-68LP/CB-68LPR Parts Locator Diagram

1 Screw Terminals 2 68-Pin I/O Connector 3 Metal Standoff Foot

1 2

S/N

ASSY183030D–01

COO

ASSY184700D–01

S/N

CB–68LPR

CB– 68LP

FOR PATENTS: NI.COM/PATENTS

2|ni.com |NI CB-68LP/CB-68LPR User Guide

Note If the accessory is missing any of the components in Figure 1, contact NI.

Note The CE marking on the CB-68LP/CB-68LPR accessories indicates

compliance with the RoHS directive 2011/65/EU only.

What You Need to Get Started

To set up and use your CB-68LP/CB-68LPR, you need the following:

CB-68LP/CB-68LPR accessory kit(s)1

Compatible 68-pin DAQ device and device documentation

The correct cable(s) for your device

0.125 in. flathead screwdriver

0.0509 to 3.31 mm2(12 to 30 AWG) wire

Wire cutters

Wire insulation stripper

Getting Started with the CB-68LP/CB-68LPR

Remove all cables from the CB-68LP/CB-68LPR before getting started. If you have not

already installed your DAQ device, refer to the installation guide that came with your DAQ

device for instructions. Complete the following steps to set up the CB-68LP/CB-68LPR.

1. (Optional) Mount the CB-68LP/CB-68LPR to a custom panel by removing the four metal

standoff feet. Refer to Figure 2 or 3 for the mounting dimensions of your accessory.

2. Connect the wires to the screw terminals by stripping 6 mm (0.25 in.) of insulation,

inserting the wires into the screw terminals, and securely tightening the screws with the

flathead screwdriver to a torque of 0.5 N · m (4.4 lb · in.). Refer to your device

documentation for the DAQ device pinout and signal information.

Caution Do not connect input voltages >30 Vrms/42 Vpk/60 VDC to the

CB-68LP/CB-68LPR. The CB-68LP/CB-68LPR are not designed for any input

voltages >30 Vrms/42 Vpk/60 VDC, even if a user-installed voltage divider reduces

the voltage to within the input range of the DAQ device. Input voltages >30 Vrms/

42 Vpk/60 VDC can damage the CB-68LP/CB-68LPR, all devices connected to it,

and the host computer.

Caution Do not use for measurements within Categories II, III, or IV.

1 You can use up to two CB-68LP/CB-68LPR accessories with M/X Series devices with two connectors.

NI CB-68LP/CB-68LPR User Guide |© National Instruments |3

3. Connect the CB-68LP/CB-68LPR(s) to the DAQ device using the appropriate cable(s) for

your device.

4. Launch Measurement & Automation Explorer (MAX). In the left panel, expand Devices

and Interfaces to confirm that your DAQ device is recognized, and then configure your

device settings.

5. Test specific device functionality. Run a Test Panel in MAX by right-clicking your DAQ

device and selecting Test Panels. Click Start to test the device functions.

When you have finished using the CB-68LP/CB-68LPR, power off any external signals

connected to the CB-68LP/CB-68LPR before you power off your computer.

Specifications

These specifications are typical at 25 °C unless otherwise noted.

Caution Do not connect hazardous voltages (>30 Vrms/42 Vpk/60 VDC) to the

CB-68LP/CB-68LPR.

Physical Characteristics

Dimensions

CB-68LP...................................................143.5 mm × 107.4 mm × 30.0 mm

(5.65 in. × 4.23 in. × 1.18 in.)

CB-68LPR................................................167.6 mm × 76.2 mm × 29.2 mm

(6.60 in. × 3.00 in. × 1.15 in.)

Weight

CB-68LP...................................................155 g (5.4 oz)

CB-68LPR................................................162 g (5.7 oz)

I/O connector....................................................One 68-pin male SCSI connector

Screw terminals ................................................68, all I/O signals are available at screw

terminals

Wire gauge................................................0.0509 to 3.31 mm2(12 to 30 AWG)

Torque.......................................................0.5 N · m (4.4 lb · in.)

Clean the hardware with a soft, nonmetallic brush.

4|ni.com |NI CB-68LP/CB-68LPR User Guide

Figure 2. NI CB-68LP Dimensions

Figure 3. NI CB-68LPR Dimensions

143.5 mm

(5.65 in.)

106.7 mm

(4.20 in.)

18.5 mm

(0.73in.)

107.4 mm

(4.23in.)

98.8mm

(3.89 in.)

4.3mm

(0.17 in.)

4X Ø 3.18(0.125)

197.6 mm

(6.60 in.)

76.2 mm

(3.00 in.)

51.3mm

(2.02 in.)

155.6 mm

(6.12 in.)

134.9 mm

(5.31 in.) 12.4 mm

(0.49 in.)

6.4 mm

(0.25 in.)

14.5 mm

(0.57 in.)

4X Ø 3.18(0.125)

12.2 mm

(0.48in.)

NI CB-68LP/CB-68LPR User Guide |© National Instruments |5

Safety Voltages

Connect only voltages that are no greater than 30 Vrms/42 Vpk/60 VDC.

Environmental

Temperature

Operating ..................................................0 to 70 °C

Storage......................................................-20 to 70 °C

Relative humidity

Operating..................................................5 to 90% RH, noncondensing

Storage......................................................5 to 90% RH, noncondensing

Pollution Degree...............................................2

Maximum altitude.............................................2,000 m

Indoor use only.

Caution TheprotectionprovidedbytheDAQdeviceandtheCB-68LP/CB-68LPR

can be impaired if it is used in a manner not described in this user guide and the user

documentation for your DAQ device.

Environmental Management

NI is committed to designing and manufacturing products in an environmentally responsible

manner. NI recognizes that eliminating certain hazardous substances from our products is

beneficial to the environment and to NI customers.

For additional environmental information, refer to theMinimize Our Environmental Impact web

page at ni.com/environment. This page contains the environmental regulations and

directives with which NI complies, as well as other environmental information not included in

this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers At the end of the product life cycle, all products must be sent to

a WEEE recycling center. For more information about WEEE recycling centers,

National Instruments WEEE initiatives, and compliance with WEEE Directive

2002/96/EC on Waste and Electronic Equipment, visit ni.com/environment/

weee.

⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑ RoHS˅

Ё೑ᅶ᠋ National Instruments ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ

(RoHS)Ǆ݇Ѣ National Instruments Ё೑ RoHS ড়㾘ᗻֵᙃˈ䇋ⱏᔩ ni.com/

environment/rohs_chinaǄ(For information about China RoHS compliance,

go to ni.com/environment/rohs_china.)

373853A-01 Apr13

Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for more information on National Instruments trademarks. Other

product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National

Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the

National Instruments Patents Notice at ni.com/patents. You can find information about end-user license agreements (EULAs) and third-party

legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/legal/export-compliance

for the National Instruments global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data.

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung