Nibe F1145PC Bedienungsanleitung

IHB EN 2004-1

531651

INSTALLATION MANUAL

Ground source heat pump

NIBE F1145PC

Quick guide

Navigation

Ok button (confirm/select)

Back button (back/undo/exit)

Control knob (move/increase/reduce)

A detailed explanation of the button functions can be found on page 35.

How to scroll through menus and make different settings is described on page 37.

Set the indoor climate

INDOOR CLIMATE

HEAT PUMP INFO

HOT WATER

The mode for setting the indoor temperature is accessed by pressing the OK button twice, when in the start

mode in the main menu.

Increase hot water volume

To temporarily increase the amount of hot water (if a hot water heater is installed to your F1145PC), first turn

the control knob to mark menu 2 (water droplet) and then press the OK button twice.

41 Important information

4Safety information

4Symbols

4Marking

5Serial number

5Recovery

5Environmental information

6Inspection of the installation

72 Delivery and handling

7Transport

7Assembly

8Supplied components

8Removing the covers

93 The heat pump design

9General

11Distribution boxes

13Cooling section (EP14)

144 Pipe connections

14General

15Dimensions and pipe connections

16Brine side

17Heating medium side

17Cold and hot water

17Docking alternatives

195 Electrical connections

19General

21Connections

23Settings

25Optional connections

28Connecting accessories

296 Commissioning and adjusting

29Preparations

29Filling and venting

30Start-up and inspection

32Setting the cooling/heating curve

357 Control - Introduction

35Display unit

36Menu system

398 Control - Menus

39Menu 1 - INDOOR CLIMATE

39Menu 2 - HOT WATER

40Menu 3 - INFO

41Menu 4 - HEAT PUMP

42Menu 5 - SERVICE

549 Service

54Service actions

6110 Disturbances in comfort

61Manage alarm

6411 Accessories

6712 Technical data

67Dimensions and setting-out coordinates

68Electrical data

69Technical specifications

71Energy labelling

75Item register

79Contact information

3Table of ContentsNIBE F1145PC

Table of Contents

Safety information

This manual describes installation and service proced-

ures for implementation by specialists.

The manual must be left with the customer.

This appliance can be used by children

aged from 8 years and above and persons

with reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given super-

vision or instruction concerning use of the

appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

Rights to make any design or technical

modifications are reserved.

©NIBE 2020.

Water may drip from the safety valve’s

overflow pipe. The entire length of the over-

flow water pipe must be routed to a suitable

drain and be inclined to prevent water pock-

ets, and must also be frost-proof. The over-

flow pipe must be at least the same size as

the safety valve. The overflow pipe must be

visible and its mouth must be open and not

located close to electrical components.

F1145PC must be installed via an isolator

switch. The cable area has to be dimensioned

based on the fuse rating used.

Symbols

NOTE

This symbol indicates danger to person or ma-

chine .

Caution

This symbol indicates important information

about what you should consider when installing

or servicing the installation.

TIP

This symbol indicates tips on how to facilitate

using the product.

Marking

The CE mark is obligatory for most products sold

in the EU, regardless of where they are made.

Classification of enclosure of electro-technical

equipment.

IPX1B

Danger to person or machine.

Read the User Manual.

NIBE F1145PCChapter 1 | Important information4

1 Important information

Serial number

The serial number can be found at the bottom right of

the front cover, in the info menu (menu 3.1) and on the

type plate (PZ1).

Serial number

Caution

You need the product's ((14 digit) serial number

for servicing and support.

Recovery

Leave the disposal of the packaging to the in-

staller who installed the product or to special

waste stations.

Do not dispose of used products with normal

household waste. It must be disposed of at a

special waste station or dealer who provides this type

of service.

Improper disposal of the product by the user results in

administrative penalties in accordance with current le-

gislation.

Environmental

information

F-GAS REGULATION (EU) NO. 517/2014

This unit contains a fluorinated greenhouse gas that is

covered by the Kyoto agreement.

The equipment contains R407C, a fluorinated green-

house gas with a GWP value (Global Warming Potential)

of 1,774. Do not release R407C into the atmosphere.

5Chapter 1 | Important informationNIBE F1145PC

Inspection of the installation

Current regulations require the heating installation to be inspected before it is commissioned. The inspection must

be carried out by a suitably qualified person.

In addition, fill in the page for the installation data in the User Manual.

DateSigna-

ture

NotesDescription

✔

Brine (page 16)

System flushed

System vented

Antifreeze

Level/Expansion vessel

Particle filter

Safety valve

Shut off valves

Circulation pump setting

Heating medium (page 17)

System flushed

System vented

Expansion vessel

Particle filter

Safety valve

Shut off valves

Circulation pump setting

Electricity (page 19)

Connections

Main voltage

Phase voltage

Fuses heat pump

Fuses property

Outside sensor

Room sensor

Current sensor

Safety breaker

Earth circuit-breaker

Setting of emergency mode thermo-

stat

NIBE F1145PCChapter 1 | Important information6

Transport

F1145PC should be transported and stored vertically in

a dry place. When being moved into a building, F1145PC

may be leant back 45 °.

Ensure that F1145PC has not been damaged during

transport.

Caution

The product can be tail heavy.

If the cooling module is pulled out and transported up-

right, F1145PC can be transported on its back.

Remove the outer panels in order to protect them when

moving in confined spaces inside buildings.

EXTRACTING THE COOLING MODULE

To simplify transport and service, the heat pump can be

separated by pulling the cooling module out from the

cabinet.

See page 57 for instructions about the separation.

Assembly

• Place F1145PC on a solid foundation indoors that can

take the heat pump's weight. Use the product's ad-

justable feet to obtain a horizontal and stable set-up.

30 - 50 mm

15 - 40 mm

20-55 mm

• Because water comes from F1145PC, the area where

the heating pump is located must be equipped with

floor drainage.

•Install with its back to an outside wall, ideally in a room

where noise does not matter, in order to eliminate

noise problems. If this is not possible, avoid placing

it against a wall behind a bedroom or other room

where noise may be a problem.

• Wherever the unit is located, walls to sound sensitive

rooms should be fitted with sound insulation.

• Route pipes so they are not fixed to an internal wall

that backs on to a bedroom or living room.

INSTALLATION AREA

Leave a free space of 800 mm in front of the product.

Approx. 50 mm free space is required on each side, to

remove the side panels (see image). The panels do not

need to be removed during service. All service on

F1145PC can be carried out from the front. Leave space

between the heat pump and the wall behind (and any

routing of supply cables and pipes) to reduce the risk of

any vibration being propagated.

(50) (50)

800

* A normal installation needs 300 – 400 mm (any side) for connection

equipment, i.e. level vessel, valves and electrical equipment.

7Chapter 2 | Delivery and handlingNIBE F1145PC

2 Delivery and handling

Supplied components

LEK

Current sensor

3 x

Room sensor

1 x

Outside sensor

1 x

Tubes for sensors

3 x

O-rings

8 x

LEK

Safety valve

0.3 MPa (3 bar)

1 x

LEK

Aluminium tape

1 x

LEK

Insulation tape

1 x

LEK

Level vessel

1 x

Temperature

sensor

WILO

LEK

WILO

2,5(22)

H- 50 - 2,5

TUV-SV-97-525

WILO

LEK

WILO

2,5(22)

H- 50 - 2,5

TUV-SV-97-525

Particle filter

6 – 10 kW

1 x G1

1 x G3/4

Compression ring

couplings

6-10 kW

2 x (ø28 x G25)

3 x (ø22 x G20)

LEK

External brine

pump (only for

10 kW)

1 x

CIRK.PUMP

External brine

pump (only for

10 kW)

1 x

LOCATION

The kit of supplied items is placed in packaging on top

of the heat pump.

Removing the covers

FRONT COVER

LEK

1. Remove the screws from the lower edge of the

front panel.

2. Lift the panel out at the bottom edge and up.

SIDE COVERS

LEK

The side covers can be removed to facilitate the install-

ation.

1. Remove the screws from the upper and lower

edges.

2. Twist the cover slightly outward.

3. Move the hatch outwards and backwards.

4. Assembly takes place in the reverse order.

NIBE F1145PCChapter 2 | Delivery and handling8

General

F1145

PF1

QN10

BT2

EB1

UB1

QM34

QM31

XL1

XL6

XL9

XL7

XL2

UB3

AA4

W130

SF1

AA4-XJ4

AA4-XJ3

UB2

QM32

QM33

PF2

EP14-AA11

EP14

VIEW FROM BEHIND

BF1

9Chapter 3 | The heat pump designNIBE F1145PC

3 The heat pump design

PIPE CONNECTIONS

Connection, heating medium flowXL1

Connection, heating medium returnXL2

Connection, brine inXL6

Connection, brine outXL7

Connection, hot water heaterXL9

HVAC COMPONENTS

Shut-off valve, heating medium flowQM31

Shut off valve, heating medium returnQM32

Shut off valve, brine outQM33

Shut-off valve, brine inQM34

Shuttle valve, climate system/water heaterQN10

SENSORS ETC.

Flow meter**BF1

Outdoor temperature sensor*BT1

Temperature sensors, heating medium flowBT2

**Only heat pumps with energy meter

* Not illustrated

ELECTRICAL COMPONENTS

Display unit

AA4-XJ3 USB socket

AA4-XJ4 Service outlet (No function)

AA4

Motor moduleAA11

Immersion heaterEB1

SwitchSF1

Network cable for NIBE UplinkW130

MISCELLANEOUS

Cooling sectionEP14

Rating platePF1

Type plate, cooling sectionPF2

Cable gland, incoming electricityUB1

Cable glandUB2

Cable gland, rear side, sensorUB3

Designations according to standard EN 81346-2.

NIBE F1145PCChapter 3 | The heat pump design10

Andere Handbücher für F1145PC

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nibe Wärmepumpe Handbücher

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung