Nibe Contura C26T High Bedienungsanleitung

www.contura.eu

C26T High

Installation

instructions

PRODUCT

Product type Stove lit with solid biofuels

Type designation Contura 26T

Manufacturing number See rating plate on the stove

Intended area of use Heating of rooms in residential buildings

Fuel Wood

MANUFACTURER

Name NIBE AB / Contura

Address Box 134, Skulptörvägen 10

SE-285 23 Markaryd, Sweden

CHECKS

According to AVCP System 3

European standard EN 13240:2001 / A2:2004

Test institute Rein-Ruhr Feuerstätten Prüfstelle, NB 1625,

has checked declared performance and issued test report no. RRF-40 08 1853

PERFORMANCE DECLARATION

No. C26T-CPR-130617-SE-1

DECLARED PERFORMANCE

Essential characteristics Performance Harmonised technical

speciﬁcation

Reaction to fire A1 WT

Minimum distance to combustible material 100 mm to rear

600 mm to side

Other safety distances according to

the installation instructions

Risk of falling embers Approved

Emissions from combustion CO 0.09%

NOx 82 mg/m3

OGC 43 mg/m3

PM 22 mg/m3

Surface temperatures Approved

Cleaning options Approved

Mechanical durability Approved

Emissions of hazardous substances Approved

Nominal output 6 kW

Efficiency 79%

Flue gas temperature in connector at nominal

output

280°C

EN 13240:2001 / A2:2004

The undersigned is responsible for the manufacture and conformity with the declared performance.

Niklas Gunnarsson, Business area manager NIBE STOVES

Markaryd, 1st July 2013

CERTIFICATE

CONTENTS

Report the installation of a stove to your

local authority.

The owner of the house is personally responsible

for ensuring compliance with the mandatory safety

requirements and must have the installation approved

by a qualified inspector. Your local chimney sweep must

also be informed of the installation, as this will affect the

routines for regular chimney-sweeping services.

WARNING!

NOTE:

The stove becomes very hot

During operation, certain surfaces of the stove become

very hot and can cause burn injuries if touched. Also, take

heed of the strong heat radiated through the door glass.

Placing flammable material closer than the safe distance

indicated may cause a fire. Smoulder combustion can cause

quick gas ignition with the risk of damage to property and

personal injury.

A warm welcome to Contura.

A warm welcome to the Contura family. We hope you

will get a great deal of pleasure from your new stove.

As a new owner of a Contura stove, you have secured

a product with timeless design and long service life.

Contura also has a combustion process that is both

environmentally friendly and efficient, for the best heat

production.

Read through these installation instructions carefully

before installation. Read how to best light your stove

in the lighting instructions.

List of Contents

Technical details 68

Supply of combustion air 69

Connection to chimney 70

Installation distances 71

Installation of C26T High 72

Installation of heat reservoir (option) 76

HANDÖL

Inaccordance with standards below

markingwas affixed:

EuropeanStandard:

SEQuality Certification, P-marked:

NOStandard NS 3059:

DEand AT Standard DIN 18.891 and

Art15a B-VG:

Type:

NominalOutput:

Fuel:

Minimundraught:

Fluegas temerature:

Energyefficiency:

Emissionof CO in cumbustion products:

Distanceto cumbustible wall (mm):

Followthe user’s instructions and use only recomended fuel

NIBEAB Box 134 SE-285 23 MARKARYD SWEDEN

2007

EN13240

Certno 0112/07

SINTEF110-0275

RRF-4007 13 90

Handöl31/31A/32/32A

5kW

Wood

12Pa

280°C

78%

0,14%

Behind150

Beside450

Corner150

HANDÖL

NIBE AB SE-85 21 Markaryd Sweden

Type:

Production no.

50-series

7090300236

403872

403871

403870

403867

403868

403869

603367

603366

603365

603362

603363

603364

Eldstadsbeklädnad

Rosterreglage Asklåda

Förbränningsluftsreglage

Brasbegränsare

Fire-box surround

Air supply control

Grate shuttle Ash-pan

Log guard

Type plate

Name of the soapstone

Technical details Important to remember!

Installation by authorised

technician

This manual contains instructions on

how the stoves must be assembled and

installed. To ensure the function and

safety of the stove, we recommend that

the installation be carried out by an

authorised technician. Contact one of

our dealers who can recommend suitable

fitters.

Building permission

Before installing a stove or erecting a

chimney, it is necessary for you to make an

application for building permission to your

local authority. Ask your local authority for

advice regarding building regulations and

the application.

Structural support

Check that the wood joists are strong

enough to bear the weight of the stove

and chimney. The stove and chimney can

usually be placed on a normal wooden joist

in a single occupancy house, if the total

weight does not exceed 400 kg.

Hearth plate

Due to the risk of embers falling out, a

flammable floor must be protected by a

hearth plate. It must extend 300 mm in

front of the stove and 100 mm on each

side of the stove, or have a 200 mm

extension on each side of the opening.

The hearth plate can consist of natural

stone, concrete, metal plate or glass. A

painted metal or glass hearth plate is

available as an accessory for these models.

Effect 3-9 kW

Nominal effect 6 kW

Efficiency 79%

Model C26T High

Weight (kg) 470*

Width (mm) 580

Depth (mm) 462

Height (mm) 1622

*Weight, C26T with heat reservoir

(option) (kg) 590

Type approved in accordance with:

European standard EN 13240

Swedish environmental and quality marking,

P-marking cert. no. 220312

Norwegian standard NS 3059, SINTEF 110-0223

German standard DIN EN/ 13240 RRF 40 08 1853

FACTS

30 mm

Ash-pan

Installation variants

Supply of combustion air

When a stove is installed in a room, the air supply demand to the

room increases. Air can be provided indirectly via a vent in the

outer wall or via a duct from the outside that is connected to the

connector on the underneath of the stove. The amount of air

needed for combustion is approx. 25m3/h.

The connector has an external diameter of 67 mm. When installing

ducts longer than 1 m, the pipe diameter must be increased to 100

mm and a correspondingly larger wall vent must be selected.

In hot areas, the duct should be insulated with 30 mm mineral

wool covered with a moisture barrier (plastic). It is important that

the lead-in, between the pipe and the wall (or floor), is sealed

using jointing compound.

A 1 m length of condensation-insulated ducting for combustion air

is available as an accessory.

SUPPLY AIR/ACCESSORY

In the case of connection through the floor, first

remove the knockout in the guide plate and any

hearth plate.

For this type of connection, first remove the valance

that sits in front of the back plate's air intake.

ca 180 mm

1 32

• The stove meets the requirements for connecting to chimneys

dimensioned for flue gas temperatures of 350°C.

• The external diameter of the connection sleeve is 150 mm.

• The stove requires a draft in the chimney of at least –12 Pa. The

draft is affected both by the length and area of the chimney, and

by how well sealed it is. The minimum recommended chimney

length is 3.5 m and a suitable cross-sectional area is 150-200

cm² (140-160 mm in diameter).

• A flue with sharp bends and horizontal routing reduces the

draught in the chimney. The maximum horizontal flue is 1 m, on

the condition that the vertical flue length is at least 5 m.

• It must be possible to sweep the full length of the flue and the

soot doors must be easily accessible.

• Carefully check that the chimney is sealed and that there is no

leakage around soot doors and flue connections.

In the bag with these installation instructions

are two wing screws for the cover.

Sweeping

When sweeping, the smoke

baffle must be removed; on the

Contura 20 series this is easily

done by lifting and then pushing

the baffle to the side.

The hot air grille must be installed before the chimney

is connected to the top.

The back panel must be installed before the stove is connected at the

rear.

Make sure that the connector

gasket does not come loose

when the connection pipe is

placed on the sleeve. If further

sealing material is required, heat-

resistant sealant may be used.

Top connection to the chimney

Rear connection to a masonry chimney

Connection to chimney

CHIMNEY

Place the stove on the

hearth plate and check

that the installation

distances are not less

than those that are given

in the figures below. The

minimum distance in

front of the stove opening

to combustible parts of

the building or interior

decoration must be at least

1 m.

When top connecting

a steel flue, please

refer to the particular

manufacturer's installation

instructions. Observe

the safety distance to

combustible material that

the steel flue requires.

A = height from floor to chimney connection upwards

B = height from floor to c/c chimney connection rear

C = distance from back to c/c chimney connection upwards

D = distance from back to chimney connection rear

E = distance from back to hole in guide plate

F = height from floor to air inlet connector (410 mm)

G = distance to hole in guide plate

*To prevent discolouration of painted fire walls, we recommend the same side distance as to combustible walls.

Installation distances

C26T High

INSTALLATION DISTANCES

365

795

740

Fire-retardant wall of

brick or concrete

238

300*

590

Fire-retardant wall of

brick or concrete

435

120

890

810

Combustible wall

288

100

600

890

500

400

300

200

300

400

500

200

Combustible wall

Permitted area for

combustible material

1622

582

2300

G 90

Combustible roof

Combustion air hose

(accessory)

442

E 150

A 1116

B 1033

F 410

C 188

D 85

502

462

Ø150

VANADIUM

No.7

CHROME

445 mm

VANADIUM

No.7

CHROME

Min 105 mm

The stove needs to be placed on a level and horizontal surface, so

the courses do not end up uneven and crooked. Otherwise, this can

result in abnormally large gaps and uneven lines.

During assembly, check that all the stones stand horizontally and

that all parts in a course are of a uniform height.

Remember to handle the stones with care. They scratch easily and

the sharp edges are vulnerable to knocks. Also, take care when the

screws are to be tightened, so as not to cause cracks.

Centre marking chimney

Installation of C26T High

INSTALLATION

VANADIUM

No. 7

CHROME

5 mm

Place the profile edge to

edge with the stone's side.

Wait to tighten this screw until

the next stone is in place.

INSTALLATION

VANADIUM

No. 7

CHROME

VANADIUM

No. 7

CHROME

VANADIUM

No. 7

CHROME

It is extremely important that the installation is inspected by an authorised chimney sweep before

the stove is used. Also read the ”Lighting instructions”, before lighting for the first time.

Final inspection of the installation

Not with the heat reservoir option

For the heat reservoir option, go to

page 76.

Press the profiles

up as far as

they go, while

tightening the

screws.

INSTALLATION

Andere Nibe Kamin im Innenbereich Handbücher

Nibe

Nibe Contura C590T Bedienungsanleitung

Nibe

Nibe Contura C690G Bedienungsanleitung

Nibe

Nibe Contura C750A Bedienungsanleitung

Nibe

Nibe Contura Ci7 Bedienungsanleitung

Nibe

Nibe Contura 556T Bedienungsanleitung

Nibe

Nibe Contura Ci8 Bedienungsanleitung

Nibe

Nibe Contura 310 Bedienungsanleitung

Nibe

Nibe Contura Ci60 Bedienungsanleitung

Nibe

Nibe Contura C i30 Bedienungsanleitung

Nibe

Nibe Contura C620 Bedienungsanleitung

Nibe

Nibe Contura 856WG Style Bedienungsanleitung

Nibe

Nibe Contura C310 Bedienungsanleitung

Nibe

Nibe Contura 580W Bedienungsanleitung

Nibe

Nibe Contura C856G Bedienungsanleitung

Nibe

Nibe Contura Style 896G Bedienungsanleitung

Nibe

Nibe C690 Style Bedienungsanleitung

Nibe

Nibe Contura C320T Bedienungsanleitung

Nibe

Nibe Contura Ci8 Bedienungsanleitung

Nibe

Nibe Contura C890 Bedienungsanleitung

Nibe

Nibe Contura Ci8 Bedienungsanleitung

Nibe

Nibe Contura C51L Bedienungsanleitung

Nibe

Nibe Contura 330 Bedienungsanleitung

Nibe

Nibe Contura 320AG Bedienungsanleitung

Nibe

Nibe Contura 320A Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch