Nibe Contura C 570 Bedienungsanleitung

C 570

www.contura.eu

Installations-

anvisning

Installation

instruction

Quality approval

The stove has been tested by the Swedish National Testing and Research Institute and meets the

applicable regulations for CE marking and the stricter requirements for P marking. Manufacture

of the product has taken place in accordance with those documents which are the basis for the

relevant type approval certification and the required manufacturing checks. The chimney must be

dimensioned for at least 350° C for both top connection directly upwards and connection directly

backwards from the rear of the stove.

Contura 570 is a Swan labelled stove.

NIBE was the first stove manufacturer in Sweden to commit to Swan labelling their stoves. The

Swan label is one aspect of our vision to be a company of the future, setting high quality standards

regarding the environment. Certification number 378-001.

CERTIFICATE

378 001

EC Declaration of

conformity

MANUFACTURER

Name NIBE AB / Contura

Address Box 134, Skulptörvägen 10, SE-285 23 Markaryd

Place of manufacture Markaryd, Sweden

PRODUCT

Product type Stove fired by solid fuel

Type designation Contura 570

Standard EN 13240 annex ZA

Intended for use Heating of living accomodation

Fuels Wood logs

Special conditions None

CE-MARKING

Issued 2010

Nominal output 5 kW

Fuel type Wood logs

Flue gas temperature 290° C

Energy efficiency 79%

Emission of CO 0,06%

Appendix

Lighting and installation instructions

Niklas Gunnarsson

Business area manager NIBE STOVES

List of Contents

Technical details 68

Removing the loose parts 68

Connection to chimney 70

Supply of combustion air 71

Installation distances 72

Assembly 73

Installing base 76

Installing drawer 77

A warm welcome to Contura

A warm welcome to the Contura family. We hope you

will get a great deal of pleasure from your new stove.

As a new owner of a Contura stove, you have secured

a product with timeless design and long service life.

Contura also has a combustion process that is both

environmentally friendly and efficient, for the best heat

production.

Read through these installation instructions carefully

before installation. Read how to best light your stove

in the lighting instructions.

The stove becomes very hot

During operation, certain surfaces of the stove become

very hot and can cause burn injury if touched. Also, take

heed of the strong heat radiated through the door glass.

Placing flammable material closer than the safe distance

indicated may cause a fire. Smoulder combustion can cause

quick gas ignition with the risk of damage to property and

personal injury.

NOTE: WARNING!

Report the installation of a stove

to your local authority.

The owner of the house is personally responsible

for ensuring compliance with the mandatory safety

requirements and must have the installation approved by

a qualified inspector. Your local chimney sweep must also

be informed about the installation as this will affect the

routines for regular chimney-sweeping services.

CONTENTS

FACTS

Effect 3-7kW

Nominal effect 5 kW

Efficiency up to 79%

Model 570

Height (mm) 1010

Width (mm) 500

Depth (mm) 440

Weight (kg) 100

Type approved in accordance with:

European standard EN-13240

Swedish environmental and quality marking,

P-marking cert. no. 220309

Norwegian standard NS 3059, SINTEF 043-140

German standard DIN, 18.891, RO-91 03 529

Danish standard DS/EN 13240 Plus,

id no. 598

Removing the loose

parts

If the insert needs to be put down

to be moved, loose components

should be removed. When the stove is

installed reinstall the components in

reverse order.

1 Fire bars

2 Grate disc

3 Heat deflector

4 Hearth cladding (Vermiculite).

Important to remember!

Technical details

Structural support

Check that the wood joists are strong

enough to bear the weight of the stove and

chimney. The stove and chimney can usually

be placed on a normal wooden joist in a

single occupancy house, if the total weight

does not exceed 400 kg.

Floor plate

Due to the risk of falling embers, a

combustible floor must be protected by a

hearth plate which covers at least 300 mm

to the front and 100 mm along each side.

The hearth plate can consist of natural

stone, concrete, metal or glass. A painted

metal or glass hearth plate is available as

an accessory for these models.

Installation by authorised

technician

This manual contains instructions about

how the stoves must be assembled and

installed. To ensure the function and safety

of the stove, we recommend that the

installation is carried out by an authorised

technician. Contact one of our dealers who

can recommend suitable fitters.

Building permission

These main insructions may give guidance

which would contravene national building

regulations. Please refer to supplementary

instructions or ask your local authority for

advice regarding building regulations.

Before installing a stove or erecting a

chimney it is necessary for you to make

a building application permission to your

local authority.

REMOVAL

How to remove the hearth surround (Vermiculite)

Handle the vermiculite with care. Lift the smoke baffle with one hand whilst removing

the sides pieces. Reinstall in reverse order

How to remove the heat deflector

LEK

ca 180 mm

LEK

CHIMNEY

Connection to chimney

Rear connection to a masonry chimney

Top connection to the chimney

Make sure that the connector

gasket does not work loose when

the connection pipe is placed

on the connector. If further

sealing material is required, heat-

resistant sealant may be used.

The soapstone is installed after making the rearward connection.

The hot air grille must be installed before chimney

top connection.

• The stove meets the requirements for connecting to chimneys

dimensioned for 350°C flue gas temperature.

• The external diameter of the connection sleeve is 150 mm.

• The stove requires a draft in the chimney of at least –12 Pa. The

draft is affected both by the length and area of the chimney, and

by how well sealed it is. The minimum recommended chimney

length is 3.5 m and suitable cross sectional area is 150-200 cm²

(140-160 mm in diameter).

• A flue with sharp bends and horizontal routing reduces the

draught in the chimney. The maximum horizontal flue is 1 m, on the

condition that the vertical flue length is at least 5 m.

• It must be possible to sweep the full length of the flue and the

soot doors must be easily accessible.

• Carefully check that the chimney is sealed and that there is no

leakage around soot doors and flue connections.

5 6

In the bag with these installation instructions

are two wing screws for the cover.

LEK

40 mm

LEK

40 mm

LEK

30 mm

0 mm

SUPPLY AIR/ACCESSORY

Supply of combustion air

When a stove is installed in a room, the demand for air supply to the

room increases. Air can be provided indirectly via a vent in the outer

wall or via a duct from the outside that is connected to the connector

on the underneath of the stove. The amount of air needed for

combustion is approx. 25m3/h.

The connector has an external diameter of 67 mm. When duct routing

further than 1 m the pipe diameter must be increased to 100 mm

and a correspondingly larger wall vent must be selected.

In hot areas the duct should be insulated with 30 mm mineral wool

covered with a moisture inhibitor (plastic). It is important that the

lead-in between the pipe and the wall (or floor) is sealed using

jointing compound.

A 1 m length of condensation-insulated ducting for combustion air is

available as an accessory.

Through the external wall

Indirect air supply through the external wall

Through floor and foundation slab

Through floor and wall-and-cavity foundation

C 570

In the back and floor plates there are knockouts

that must be removed to insert pipes or for air

supply if the stove is equipped with a lower hatch

and/or fan (accessory).

Installation variants

Leave a 40 mm gap between

the condensation insulation

and the bottom of the stove.

C 570

* If the stove is placed on a hearth plate made of glass for example (accessory), the height from the floor is affected by a distance corresponding to the thickness of the hearth plate. Also applies to

separate glass hearth plates (accessory).

** To prevent discolouration of painted non-flammable walls we recommend that the same side distance as to combustible walls is used.

The minimum distance in front of

the stove opening to combustible

parts of the building or interior

decoration must be at least 1 m.

When top connecting a steel flue,

please refer to the particular

manufacturer's installation

instructions. Observe the safety

distance to combustible material

that the steel flue requires.

Installation distances

WHEN INSTALLING TURNTABLE (OPTION) the

following installation distances do not apply.

See the separate installation instructions for

turntable.

A = height from floor to chimney

connection upwards

B = height from floor to c/c chimney

connection rear

C = height from floor to air inlet

D = height from floor to lower edge

of hatch

A separate glass hearth

plate (accessory)

increases the connection

height to the chimney

by 10 mm. The spacers

supplied with the hearth

plate are installed on the

stove before connection.

INSTALLATION DISTANCES

1010

496

2000

Air inlet Ø67

Combustible roof

D 300

139

B 850

A 942

C 340

438

Air inlet Ø67

Ø150

280

565

670

800

Fire-retardant wall of

brick or concrete

310

100

595

740

Combustible wall

750

500

240

100

200

300

400

160

260

360

Combustible wall

320*

700

1100

70*

190

Fire-retardant wall of

brick or concrete

Permitted

area for

combustible

parts of the

building

VANADIUM

No.7

CHROME

x 3

VANADIUM

No.7

CHROME

Installing C 570

ASSEMBLY

To facilitate the installation of

the side glass, the two upper

screws for the back panel must

not be tightened before the

side glass is installed.

Installing rating plate

Supplied rating plate positioned on underneath of heat deflector,

or with fan option on the inside of the stove.

ASSEMBLY

Clean all glass

thoroughly prior to

installation!

Andere Nibe Holzofen Handbücher

Nibe

Nibe Contura 620G Bedienungsanleitung

Nibe

Nibe Contura 890T Style Bedienungsanleitung

Nibe

Nibe Flakt Contura C600 Bedienungsanleitung

Nibe

Nibe Contura C890T Style Bedienungsanleitung

Nibe

Nibe Contura C886G Bedienungsanleitung

Nibe

Nibe Contura C800 Style Bedienungsanleitung

Nibe

Nibe Contura 890TG Style Bedienungsanleitung

Nibe

Nibe Contura 620T Bedienungsanleitung

Nibe

Nibe Contura Style 896G Bedienungsanleitung

Nibe

Nibe Contura C690AG Bedienungsanleitung

Nibe

Nibe Contura 590T Bedienungsanleitung

Nibe

Nibe Contura 600 Style Bedienungsanleitung

Nibe

Nibe Contura 856TG Bedienungsanleitung

Nibe

Nibe Contura 520T Bedienungsanleitung

Nibe

Nibe Contura 870G Style Bedienungsanleitung

Nibe

Nibe Contura C556T Bedienungsanleitung

Nibe

Nibe Contura C 880 Bedienungsanleitung

Nibe

Nibe Contura 690AG Style Bedienungsanleitung

Nibe

Nibe Contura C520 Bedienungsanleitung

Nibe

Nibe C856T Style Bedienungsanleitung

Nibe

Nibe Contura 330G Bedienungsanleitung

Nibe

Nibe Contura C620T Bedienungsanleitung

Nibe

Nibe Contura C800 Style Bedienungsanleitung

Nibe

Nibe Contura C886 Bedienungsanleitung

Beliebte Holzofen Handbücher anderer Marken

Plamen

Plamen ECO MINIMAL 50 Bedienungsanleitung

RAIS

RAIS 800 Bedienungsanleitung

Henley

Henley Arklow Bedienungsanleitung

Jøtul

Jøtul F 500 Bedienungsanleitung

Englander

Englander BLUE RIDGE 100 Bedienungsanleitung

WoodPro

WoodPro WS-TS-1500 Bedienungsanleitung

Contura

Contura C 586W Bedienungsanleitung

Nordpeis

Nordpeis N-20 T Bedienungsanleitung

Palazzetti

Palazzetti EVA Konfigurationshandbuch

Lopi

Lopi 1250 Republic Bedienungsanleitung

Panadero

Panadero CAPRI 3V Programmierhandbuch

RAIS

RAIS RONDO 92 Bedienungsanleitung

RAIS

RAIS attika NEXO 100 GAS Bedienungsanleitung

ADURO

ADURO 15-3 Benutzerhandbuch

Pacific energy

Pacific energy SUPER 27 SPECTRUM Bedienungsanleitung

Avalon

Avalon Olympic 11190 Bedienungsanleitung

Ventis

Ventis HES350 Bedienungsanleitung

IronStrike

IronStrike Striker S160GL Bedienungsanleitung