Nibe Contura C 720T Bedienungsanleitung

www.contura.eu

C 720T

Installation

instructions

CERTIFICATE

PRODUCT

Product type Stove lit with solid biofuels

Type designation Contura 720T

Manufacturing number See rating plate on the stove

Intended area of use Heating of rooms in residential buildings

Fuel Wood

MANUFACTURER

Name NIBE AB / Contura

Address Box 134, Skulptörvägen 10

SE-285 23 Markaryd, Sweden

CHECKS

According to AVCP System 3

European standard EN 13240:2001 / A2:2004

Test institute Rein-Ruhr Feuerstätten Prüfstelle, NB 1625,

has checked declared performance and issued test report no. RRF-40 16 4275

PERFORMANCE DECLARATION

No. C720T-CPR-160329-SE-1

DECLARED PERFORMANCE

Essential characteristics Performance Harmonised technical

speciﬁcation

Reaction to fire A1 WT

Minimum distance to combustible material Rear: 100 mm

Side: 400 mm

Other safety distances according to

the installation instructions

Risk of falling embers Pass

Emissions from combustion CO 0.1%

NOx 103 mg/m3

OGC 77 mg/m3

PM 23 mg/m3

Surface temperatures Pass

Cleaning options Pass

Mechanical durability Pass

Emissions of hazardous substances Pass

Nominal output 5 kW

Efficiency 80%

Flue gas temperature in connector at nominal

output

315°C

EN 13240:2001 / A2:2004

The undersigned is responsible for the manufacture and conformity with the declared performance.

Niklas Gunnarsson, Business area manager NIBE STOVES

Markaryd, March 29, 2016

WARNING!

The stove becomes very hot

During operation, certain surfaces of the stove become very

hot and can cause burn injuries if touched. Also, take heed

of the strong heat radiated through the door glass. Placing

flammable material closer than the safe distance indicated

may cause a fire. Smoulder combustion can cause quick gas

ignition with the risk of damage to property and personal

injury.

NOTE:

Report the installation of a stove to your

local authority.

The owner of the house is personally responsible for ensuring

compliance with the mandatory safety requirements and

must have the installation approved by a qualified inspector.

Your local chimney sweep must also be informed about the

installation as this will affect the routines for regular chimney-

sweeping services.

List of Contents

Technical details 68

Prior to installation 68

Connection to chimney 69

Supply of combustion air 70

Installation distances 71

Installing suspension profiles 72

Installing the soapstone 75

Removing the loose parts 77

Adjustment of the base door 78

A warm welcome to Contura.

A warm welcome to the Contura family. We hope you

will get a great deal of pleasure from your new stove.

As a new owner of a Contura stove, you have secured

a product with timeless design and long service life.

Contura also has a combustion process that is both

environmentally friendly and efficient, for the best heat

production.

Read through these installation instructions carefully

before installation. Read how to best light your stove

in the lighting instructions.

CONTENTS

FACTS

Effect 3-7 kW

Nominal effect 5 kW

Efficiency up to 80%

Model 720T

Height (mm) 1179

Width (mm) 556

Depth (mm) 407

Weight (kg) 210

Type approved in accordance with:

European standard EN-13240

NS 3059 (Norway)

DIN Plus (Germany)

Art. 15a B-VG (Austria)

Clean Air Act. (UK)

Prior to installation

If the insert needs to be put down

to be moved, loose components

should be removed. When the stove is

installed reinstall the components in

reverse order.

1 Fire bars

2 Grate disc

3 Heat deflector

4 Fire bricks

Installation by authorised

technician

This manual contains instructions about

how the stove must be assembled and

installed. To ensure the function and safety

of the stove, we recommend that the

installation is carried out by an authorised

technician. Contact one of our dealers who

can recommend suitable fitters.

Building application

These main instructions may give guidance

which would contravene national building

regulations. Please refer to supplementary

instructions or ask your local authority for

advice regarding building regulations.

Before installing a stove or erecting a

chimney it is necessary for you to make a

building permission application to your

local authority.

Structural support

Check that the wood joists are strong

enough to bear the weight of the stove and

chimney. The stove and chimney can usually

be placed on a normal wooden joist in a

single occupancy house, if the total weight

does not exceed 400 kg.

Floor plate

Due to the risk of falling embers, a

flammable floor must be protected by a

hearth plate. It must extend 300 mm in

front of the stove and 100 mm on each side

of the stove, or have a 200 mm extension

on each side of the opening. The hearth

plate can consist of natural stone, concrete,

metal plate or glass. A painted metal

or glass hearth plate is available as an

accessory for these models.

Important to remember!Technical details

ca 180 mm

4 65

1 32

CHIMNEY

Connection to chimney

Rear connection to a masonry chimney

Top connection to the chimney

Make sure that the connector

gasket does not work loose

when the connection pipe

is placed on the connector.

If further sealing material

is required, heat-resistant

sealant may be used.

The back panel must be installed before the stove is rear connected.

The hot air grille must be installed before

chimney top connection.

• The stove meets the requirements for connecting to chimneys

dimensioned for 350°C flue gas temperature.

• The external diameter of the connection sleeve is 150 mm.

• The stove requires a draft in the chimney of at least –12 Pa. The

draft is affected both by the length and area of the chimney, and

by how well sealed it is. The minimum recommended chimney

length is 3.5 m and suitable cross sectional area is 150-200 cm²

(140-160 mm in diameter).

• A flue with sharp bends and horizontal routing reduces the

draught in the chimney. The maximum horizontal flue is 1 m, on the

condition that the vertical flue length is at least 5 m.

• It must be possible to sweep the full length of the flue and the

soot doors must be easily accessible.

• Carefully check that the chimney is sealed and that there is no

leakage around soot doors and flue connections.

In the bag with these installation instruc-

tions are two wing screws for the lid.

40 mm

SUPPLY AIR

Supply of combustion air

When a stove is installed in a room, the demand for air supply to the

room increases. Air can be provided indirectly via a vent in the outer

wall or via a duct from the outside that is connected to the connector

on the underneath of the stove. The amount of air needed for

combustion is approx. 15m3/h.

The connector has an external diameter of 67 mm. When duct

routing further than 1 m the pipe diameter must be increased to 100

mm and a correspondingly larger wall vent must be selected.

In hot areas the duct should be insulated with 30 mm mineral wool

covered with a moisture inhibitor (plastic). It is important that the

lead-in between the pipe and the wall (or floor) is sealed using

jointing compound.

A 1 m length of condensation-insulated ducting for combustion air is

available as an accessory.

Through the external wall.

Indirect air supply through the external wall.

Through floor and foundation slab.

Through floor and wall-and-cavity foundation.

In the back and floor plates there are

knockouts that must be removed to

insert the pipe.

Installation variants

Leave a 40 mm gap between

the condensation insulation

and the bottom of the stove.

C 720T

INSTALLATION DISTANCES

* If the stove is placed on a hearth plate made of glass for example (accessory), the height from the floor is affected by a distance corresponding to the thickness of the hearth plate. Also applies to

separate glass hearth plates (accessory).

** To prevent discolouration of painted non-flammable walls we recommend that the same side distance as to combustible walls is used.

The minimum distance in front of

the stove opening to combustible

parts of the building or interior

decoration must be at least 1 m.

The dimension diagrams only

show the minimum permitted

installation distances for the

stove. When connecting to a steel

flue, also note the safety distance

requirements of the flue. The

safety distance between an un-

insulated flue and a combustible

part of the building should be at

least 300 mm.

Installation distances

A = height from floor to

chimney connection

upwards

B = height from floor to c/c

chimney connection rear

C = height from floor to air

inlet

D = height from floor to lower

edge of hatch

A separate glass hearth

plate (accessory)

increases the connection

height to the chimney by

10 mm.

Permitted area

for combustible

parts of the

building

D 488

556

1179

2100*

126*

Combustible roof

407

211

A 1129*

139

B 1039*

C 420

Ø150

Air inlet Ø67

100

361

643

100

707

Combustible wall

900

311

593

50**

636

Fire-retardant wall of

brick or concrete

478

200**

700

1100

261

50**

Fire-retardant wall of

brick or concrete

678

400

479

311

100

Combustible wall

VANADIUM

No. 7

CHROME

1 2

Installing suspension profiles

ASSEMBLY

VANADIUM

No. 7

CHROME

ASSEMBLY

Andere Nibe Holzofen Handbücher

Nibe

Nibe Contura 620G Bedienungsanleitung

Nibe

Nibe Contura Ci50 Bedienungsanleitung

Nibe

Nibe Contura 896 Style Bedienungsanleitung

Nibe

Nibe Contura C886G Bedienungsanleitung

Nibe

Nibe Contura C896 Style Bedienungsanleitung

Nibe

Nibe Contura C596 Bedienungsanleitung

Nibe

Nibe Contura 870G Style Bedienungsanleitung

Nibe

Nibe Contura C590T Bedienungsanleitung

Nibe

Nibe Contura 856TG Bedienungsanleitung

Nibe

Nibe Flakt Contura C600 Bedienungsanleitung

Nibe

Nibe Contura 500 Style Bedienungsanleitung

Nibe

Nibe 586 Style Bedienungsanleitung

Nibe

Nibe Contura 690AG Style Bedienungsanleitung

Nibe

Nibe Contura C690 Bedienungsanleitung

Nibe

Nibe Contura C520 Bedienungsanleitung

Nibe

Nibe Contura C690AG Bedienungsanleitung

Nibe

Nibe Contura C210 Bedienungsanleitung

Nibe

Nibe Contura C810G Style Bedienungsanleitung

Nibe

Nibe Contura 310G Bedienungsanleitung

Nibe

Nibe Contura 890TG Style Bedienungsanleitung

Nibe

Nibe Contura C870G Bedienungsanleitung

Nibe

Nibe Contura C870 Bedienungsanleitung

Nibe

Nibe Contura 690 Style Bedienungsanleitung

Nibe

Nibe Contura C886 Bedienungsanleitung

Beliebte Holzofen Handbücher anderer Marken

Plamen

Plamen ECO MINIMAL 50 Bedienungsanleitung

RAIS

RAIS 800 Bedienungsanleitung

Henley

Henley Arklow Bedienungsanleitung

Jøtul

Jøtul F 500 Bedienungsanleitung

Englander

Englander BLUE RIDGE 100 Bedienungsanleitung

WoodPro

WoodPro WS-TS-1500 Bedienungsanleitung

Contura

Contura C 586W Bedienungsanleitung

Nordpeis

Nordpeis N-20 T Bedienungsanleitung

Palazzetti

Palazzetti EVA Konfigurationshandbuch

Lopi

Lopi 1250 Republic Bedienungsanleitung

Panadero

Panadero CAPRI 3V Programmierhandbuch

RAIS

RAIS RONDO 92 Bedienungsanleitung

RAIS

RAIS attika NEXO 100 GAS Bedienungsanleitung

ADURO

ADURO 15-3 Benutzerhandbuch

Pacific energy

Pacific energy SUPER 27 SPECTRUM Bedienungsanleitung

Avalon

Avalon Olympic 11190 Bedienungsanleitung

Ventis

Ventis HES350 Bedienungsanleitung

IronStrike

IronStrike Striker S160GL Bedienungsanleitung