Nidec Unidrive M100 Montageanleitung

0478-0384-01

1 Safety information

2 Introduction

This document covers the UL conduit box mounting instructions for

Unidrive M100 to M400, frame size 4 drives and derivatives.

When fitted, the drive meets the requirement for Type 1 protection

according to UL50 and UL50E.

Type 1 enclosures are intended for indoor use only. They provide a

degree of protection to personnel against incidental contact with the

enclosed equipment and a degree of protection against falling debris.

The following items are supplied in the kit:

Table 2-1 Contents of the kit (CT part number: 3470-0102)

The installed conduit kit does not change the width or depth of the drive.

However, this conduit kit will add 103 mm (4.0 in) to the height of the

drive.

Table 2-2 shows the combined drive and conduit box dimensions.

Table 2-2 Dimensions

3 Installation

Figure 3-1 Removing the drive terminal cover

• Use flat blade screwdriver to remove the drive terminal cover by

turning the cover release 30° counter clockwise and sliding the

cover downward (1).

Unidrive M100 to M400 Size 4

UL Conduit Box Installation Sheet

Follow the instructions

The mechanical and electrical installation instructions must be adhered to. Any questions or doubt should be referred to the supplier of the

equipment. It is the responsibility of the owner or user to ensure that the installation of the drive and any external option unit, and the way

in which they are operated and maintained, comply with any applicable legislation, regulation, and code of practice in the country in which

the equipment is used.

Competence of the installer

The drive must be installed by qualified personnel who are familiar with the requirements for safety and EMC. The installer is responsible

for ensuring that the end product or system complies with all the relevant laws in the country where it is to be used.

WARNING

Description Image Qty

Conduit box x 1

Conduit cover x 1

Grounding clamp x 3

M4 x 16 torx taptite screw x 8

UL conduit box installation sheet x 1

Frame

size

HWD

mm in mm in mm in

4 362 14.3 115 4.5 175 6.9

Stored charge

The drive contains capacitors that remain charged to a

potentially lethal voltage after the AC and / or DC power

supply has been disconnected. If the drive has been

energized, the power supply must be isolated at least ten

minutes before work may continue.

Normally, the capacitors are discharged by an internal

resistor. Under certain, unusual fault conditions, it is possible

that the capacitors may fail to discharge, or be prevented

from being discharged by a voltage applied to the output

terminals. If the drive has failed in a manner that causes the

display to go blank immediately, it is possible the capacitors

will not be discharged. In this case, consult Control

Techniques or their authorized distributor.

WARNING

0478-0384-01

Figure 3-2 Holes for conduit fittings

• Using the pilot holes provided on the bottom of the conduit box, drill holes for appropriately sized conduit fittings. Motor cables with motor ground

wire (1), supply cables with supply ground wire (2), and control/communication cables (if applicable) (3) need to be run in separate conduits.

Figure 3-3 Installation of conduit connection box

• Attach the conduit box (1) to the grounding bar (2) using the four M4 x 8 screws provided with the drive. Maximum recommended torque is

1.5 N m (13 lb in).

• Attach the conduit fittings to the conduit box holes; run the conduit to the drive.

• Run the motor cables (U,V, W) and motor ground wire through the back-right conduit. Connect the wires to the motor connector (U,V,W) (3).

Maximum recommended torque for screw terminals is 1.4 N m (12 lb in).

• Run the supply cables (L1,L2,L3) and supply ground wire through the back-left conduit. Connect the wires to the supply connector (L1,L2,L3) (3).

Maximum recommended torque for screw terminals is 1.4 N m (12 lb in).

• Fasten M4 ring terminals, suitable for the wire size, to the supply ground and motor ground wires. Connect the ground wires to the conduit box

grounding locations using M4 x 16 screws (4). Maximum recommended torque is 1.5 N m (13 lb in).

• Run the control cables through the front-center conduit. Connect the control cables to the control connector as required (5). Maximum

recommended torque for control terminals is 0.2 N m (2 lb in).

• Secure all cables and cable shielding to the conduit box using the grounding clamps and M4 x 16 screws (6). Maximum recommended torque is

1.5 N m (13 lb in).

• Replace the drive terminal cover by laying it on the drive and sliding it upward (7).

• Attach the conduit box cover to the conduit box using two M4 x 16 screws (8). Maximum recommended torque is 1.5 N m (13 lb in).

Andere Handbücher für Unidrive M100

Dieses Handbuch passt für folgende Modelle

Andere Nidec Gleichstromantrieb Handbücher

Nidec

Nidec HVAC Drive H300 Bedienungsanleitung

Nidec

Nidec LEROY-SOMER POWERDRIVE MD2R Series Bedienungsanleitung

Nidec

Nidec E300 Series Leitfaden

Nidec

Nidec Unidrive M201 Bedienungsanleitung

Nidec

Nidec Unidrive M702 Bedienungsanleitung

Nidec

Nidec Answer Drives 700E Handbuch

Nidec

Nidec LEROY-SOMER Bedienungsanleitung

Nidec

Nidec Power Module Frame 12 Bedienungsanleitung

Nidec

Nidec Commander C200 Bedienungsanleitung

Nidec

Nidec COMMANDER S100 Bedienungsanleitung

Nidec

Nidec LEROY-SOMER Commander ID30 Series Bedienungsanleitung

Nidec

Nidec Powerdrive MD2MS Bedienungsanleitung

Nidec

Nidec AD1000 Bedienungsanleitung

Nidec

Nidec Answer Drives 1000 Series Betriebsanleitung

Nidec

Nidec LEROY-SOMER ORTHOBLOC 3000 Bedienungsanleitung

Nidec

Nidec LEROY-SOMER Powerdrive MD2 Kurzanleitung

Nidec

Nidec Digitax ST Series Bedienungsanleitung

Nidec

Nidec HVAC Drive H300 Montageanleitung

Nidec

Nidec NE200 Series Bedienungsanleitung

Nidec

Nidec AD3000 Gebrauchs- und Pflegehandbuch

Nidec

Nidec Control Techniques Unidrive M Modular Bedienungsanleitung

Nidec

Nidec Unidrive M100 Bedienungs- und Wartungsanleitung

Nidec

Nidec M600-M70X Montageanleitung

Nidec

Nidec HVAC Drive H300 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung