Nilfisk-Advance Aquamatic Selectric 56263500 Bedienungsanleitung

revised 11/00 FORM NUMBER 56041244

Advance

Aquamatic Selectric™

Model 56263500

This parts list is for machines after serial number 470048

OPERATOR

MANUAL

INDEX

PAGE

AFTER USE ........................................................... 8

GROUNDING INSTRUCTIONS ............................. 4

IMPORTANT SAFETY INSTRUCTIONS ............... 3

INTRODUCTION .................................................... 2

KNOW YOUR MACHINE ....................................... 6

MAINTENANCE ..................................................... 9

OPERATION........................................................... 7

PREPARING THE MACHINE FOR USE................ 5

INTRODUCTION

This manual will help you get the most from your Advance AquaMatic Selectric™. Read

it thoroughly before operating the machine.

This product is intended for commercial use only.

PARTS AND SERVICE

Repairs, when required, should be performed by your Authorized Advance Service Center,

who employs factory trained service personnel, and maintains an inventory of Advance

original replacement parts and accessories.

Call the ADVANCE DEALER named below for repair parts or service. Please specify the

Model number and Serial number when discussing your machine.

(Dealer, affix service sticker here.)

NAME PLATE

The Model Number and Serial Number of your machine are shown on the Nameplate on

the right side of the machine. This information is needed when ordering repair parts for the

machine. Use the space below to note the Model Number and Serial Number of your

machine for future reference.

MODEL NUMBER _________________

SERIAL NUMBER _________________

UNCRATING

When the machine is delivered, carefully inspect the shipping carton and the machine for

damage. If damage is evident, save the shipping carton so that it can be inspected by the

trucking company that delivered it. Contact the trucking company immediately to file a

freight damage claim.

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

Read all instructions before use.

WARNING!

To reduce the risk of fire, electric shock, or injury:

• Do not leave the appliance when it is plugged in. Unplug the unit from the outlet when not in use and before

servicing.

WARNING!

• To avoid electric shock, use indoors only.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children.

• Use only as described in this manual. Use only the manufacturer’s recommended attachments.

• Do not use with a damaged cord or plug. If the appliance is not working as it should, has been dropped,

damaged, left outdoors, or dropped into water, return it to a service center.

• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges

or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not handle plug or appliance with wet hands.

• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and

anything that may reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may

be present.

• Connect to a properly grounded outlet only. See Grounding Instructions.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should electically malfunction, grounding provides a

path of least resistance for electric current to reduce the risk of electric shock. This appliance

is equipped with a cord having an equipment-grounding conductor and grounding plug. The

plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

DANGER!

Improper connection of the equipment-grounding conductor can result in a risk of electric

shock. Check with a qualified electrician or service person if you are in doubt as to whether

the outlet is properly grounded. Do not modify the plug provided with the appliance. If it will

not fit the outlet, have a proper outlet installed by a qualified electrician.

This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks

like the plug illustrated in Figure 1 below. A temporary adapter illustrated in Figures 2 and

3 may be used to connect this plug to a 2-pole receptacle as shown in Figure 2 if a properly

grounded outlet is not available. The temporary adapter should be used only until a properly

groundedoutlet (Figure1) canbe installedby aqualified electrician.The green-colored rigid

ear, tab, or the like extending from the adapter must be connected to a permanent ground

such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held

in place by a metal screw.

TAB FOR

GROUNDING

SCREW

ADAPTER

METAL SCREW

GROUNDED

OUTLET BOX

GROUNDED

OUTLET

GROUNDED PIN

Figure 1 Figure 2 Figure 3

PREPARING THE MACHINE FOR USE

FILL THE SOLUTION TANK

1. Lift the front Solution Fill Cover off the machine.

2. Read the dilution instructions on the chemical container. Then figure the proper amount

of chemical to mix with 25 gallons (94.5 liters) of water. For best results, use the

Advance CarpeTeam™ Extraction Cleaner chemical specially formulated for use with

Advance carpet extractors.

3. Pour the chemical in the solution tank and fill the tank with warm water to 1-3/4 inches

below the inside edge of the opening.

4. Put the Solution Fill Cover back on the machine.

CAUTION!

Use only low-sudsing, liquid detergents designed for carpet extraction.

PRE-SPRAY THE CARPET

Pre-spray spots and heavy traffic areas before extracting. Use a hand-held bottle sprayer

or a pressurized “Hudson” type sprayer. Mix the pre-spray according to the chemical

manufacturer’s directions. For best results, use the Advance CarpeTeam™ Pre-Spray

chemical specially formulated for use with Advance carpet extractors.

PLAN FOR CLEANING

Before you begin extracting, look at the area to be cleaned and plan your work. Divide the

space into sections. Overlap each pass 2 inches (5 cm).

KNOW YOUR MACHINE

14. Wheel Drive Circuit Breaker (2 Amp)

15. Vacuum Motor Circuit Breaker (13 Amp)

16. Drive Pedal

17. Brush Pedal

18. Solution Hose Coupler

19. Solution Filter

20. Recovery Tank Drain Hose

21. Plug Lug

22. Main Switch

23. Drive Lever

24. Vacuum Hose

25. Recovery Hose

1. Reverse Button

2. Decrease Speed Button

3. Speed Indicator Lights

4. Solution Button

5. Increase Speed Button

6. Recovery Tank Cover

7. Solution Fill Cover

8. Accessory Connection

9. Brush Height Adjustment

10. Solution Shut-Off Lever

11. Brush Drive Circuit Breaker (6 Amp)

12. Power Cord

13. Solution Hose

123

4567

TO LEFT SIDE OF COVER

TO RIGHT SIDE OF COVER

SHOWN IN

THE "ON" POSITION

OPERATION

1. Follow the instructions in the

Preparing the Machine for Use

section of this manual.

2. Connect the Power Cord (12) to the machine, then plug the Power Cord into a properly

grounded outlet.

3. Make sure the Solution Fill Cover (7) and the Recovery Tank Cover (6) are firmly in

place and the Solution Shut-Off Lever (10) is in the ON position. Then turn the Main

Switch (22) ON.

4. Put the Brush Pedal (17) UP to lower the brush to the floor.

5. Step DOWN on the Drive Pedal (16) and push the pedal to the right to engage the drive

motor.

6. Pull and hold the Drive Levers (23) UPto propelthe machine. Toadjust thetravel speed,

press the Increase Speed Button (5) or the Decrease Speed Button (2). To move

backward, hold down the Reverse Button (1) while pulling the Drive Levers; release the

Reverse Button to move forward again.

Note: There will be a slight pause between direction changes.

7. Press the Solution Button (4) to dispense solution to the brush. The Solution Button will

light up to indicate that the solution is ON. Solution is dispensed only while moving

Forwardandautomaticallyshuts offin Reverse.Press theSolution Buttonagain tostop

solution flow; the light will turn off.

8. Watch the fluid entering the recovery tank. If there is a large amount of suds in the

recovery tank, add a defoamer chemical to the recovery tank.

CAUTION!

Empty the tank before the fluid or foam enters the right tube on the recovery tank

cover.

If there is little or no fluid entering the recovery tank, look to the Solution Hose (13) at

the back of the machine. If there is no fluid running through the Solution Hose, the

solution tank may be empty. Refill the solution tank with water and the proper ratio of

cleaning chemical.

USING ATTACHMENTS

To use accessory tools, attach the accessory vacuum hose to the left tube on the recovery

tank cover. Attach the accessory solution hose to the Accessory Connection (8). Connect

the other end of the vacuum and solution hoses to the accessory tool. When using

accessory tools, step DOWN on the Brush Pedal (17) to raise the brush.

See your Advance Distributor for accessories that may be used with the AquaMatic

Selectric™ including:

• 260387 Drag Tool

• 249318 15 foot (4.5 meter) Extractor Hose Assembly

• 204203 Hand Tool

• 260340 Deluxe Hand Tool with Extractor Hose

• 249311 Power Liquidator

AFTER USE

1. Turn the Main Switch (22) OFF.

2. Step DOWN and lock the Brush Pedal (17) to raise the brush.

3. Put the Drive Pedal (16) UP to disengage the drive belt.

4. Unplug the Power Cord (12) from the power outlet.

5. Unhook the Recovery Tank Drain Hose (20), direct the hose to a floor drain or bucket.

Remove the hose plug, empty the recovery tank and rinse it with clean water.

6. Turn the Solution Lever (10)OFF and disconnect the Solution Hose Coupler (18).Direct

the hose to a floor drain or bucket, then turn the Solution Lever ON to empty the solution

tank. Rinse the tank with clean water.

7. Unscrew the Solution Filter (19) cover and clean the screen.

8. Wipe the machine with a damp cloth. Do not use abrasive chemical or solvents.

9. Perform any required maintenance before storage.

MAINTENANCE SCHEDULE

MAINTENANCE ITEM WEEKLY MONTHLY YEARLY

Clean & Check Power Brush X

Clean Pick-Up Tool X

Clean Spray Nozzle X

Lubrication X

Clean the Vacuum Exhaust Filter X

Check Vacuum Motor Brushes X

Check Wheel Drive Motor Brushes X

Clean the Solution Bladder X

10. Store the machine in a clean, dry place with the tank covers open.

MAINTENANCE

WARNING!

Unplug the power cord before attempting any service or maintenance work to the machine.

MAINTENANCE NOTE

With the tanks empty and the power cord unplugged, tip the machine forward onto its nose

for access to the Power Brush, Pick-Up Tool, and Spray Nozzle.

POWER BRUSH

Once a week, check the brush and remove any built-up string, hair or carpet fibers. Check

the bristle length. Change the brush when the brush bristles are worn to 1/4 inch (6 mm).

PICK-UP TOOL

Once a week, check the pick-up tool and remove any built-up string, hair or carpet fibers.

SPRAY NOZZLE

Once a week, remove the spray nozzle located under the machine just in front of the brush.

Soak the nozzle overnight in a vinegar and water rinse to remove chemical deposits.

LUBRICATION

Once a month (or every 30 hours), lubricate all pivot points on the pick-up tool. For best

results, use a spray silicone lubricant.

Once a month, pump grease into the grease fitting on the caster wheel until it seeps out

around the bearing. Wipe off the excess grease to avoid staining carpet.

Inhaltsverzeichnis

Andere Nilfisk-Advance Schrubber Handbücher

Nilfisk-Advance

Nilfisk-Advance Warrior ST Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Nilfisk Smart Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SC800 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance ecoflex BA 551D Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance 56390916 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance MX 585 Betriebsanleitung

Nilfisk-Advance

Nilfisk-Advance Advance SC400 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance BR 1000 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SC530 53 BD GO Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Advance SC750 ST Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Advance SC900 ST-28D Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance BA 450 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance BA 430S Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW4000 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Cr 1100 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Advance SC400 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SC250 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance BA 450 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Advenger BR 855 Benutzerhandbuch

Nilfisk-Advance

Nilfisk-Advance SC3500 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SC530 Stücklistenhandbuch

Nilfisk-Advance

Nilfisk-Advance SC351 Benutzerhandbuch

Nilfisk-Advance

Nilfisk-Advance MX 307 H Betriebsanleitung

Nilfisk-Advance

Nilfisk-Advance CA 430 S Bedienungsanleitung

Beliebte Schrubber Handbücher anderer Marken

Olympus

Olympus M200H Bedienungsanleitung

Clarke

Clarke BEXT 100H Installations- und Betriebsanleitung

JOHNY VAC

JOHNY VAC JVC70BCT Bedienungsanleitung

RCm

RCm Elan Series Handbuch

Kärcher

Kärcher B 120 W Bedienungsanleitung

Truvox

Truvox Orbis MotorScrubber 20 Bedienungsanleitung

Numatic

Numatic TTB 4045/100 Bedienungsanleitung

U.S. Products

U.S. Products PEX 500-C-TICK Betriebsanleitung

Mclennan

Mclennan C510 Bedienungsanleitung

Tennant

Tennant T20 LPG Bedienungsanleitung

Columbus

Columbus ARA 66 BM 100 Bedienungsanleitung

Numatic

Numatic TTV 678G / 300T Bedienungsanleitung

American-Lincoln

American-Lincoln 505-945 Bedienungsanleitung

Floorpul

Floorpul ruby 48 blt Benutzerhandbuch

Onyx

Onyx RX-34 Bedienungsanleitung

Dustbane

Dustbane Hurricane 400 Bedienungsanleitung

Sana

Sana EUJ-702 Bedienungsanleitung

REMS

REMS Twist Bedienungsanleitung