Nilfisk-Advance MX 521 H Bedienungsanleitung

MX 521 H

EXTRACTOR

220 - 240V EU

10.22.2007

20122007

INFORMATION

OPERATING

INSTRUCTIONS

CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ

ALL SECTIONS OF THIS INSTRUCTION MANUAL

11-600205211REVA

IMPORTANT SAFETY INSTRUCTIONS

This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops,

and offices other than normal residential housekeeping purposes.

When using any electrical appliance, basic precautions should always be followed, including the following:

NOTE: Read all instructions before using this machine.

WARNING!

To reduce the risk of fire, electric shock, or injury:

•Do not leave the machine unattended when it is plugged-in. Unplug the unit from the power

outlet when not in use.

•Unplug the machine from the power outlet before cleaning or servicing.

•Turn off all controls before unplugging.

•To avoid electric shock, do not expose to rain or snow. Store and use indoors.

•Wear hearing protection if desired. The measured sound level of the MX 521 H is 75dB(A).

•Do not allow to be used as a toy. Close attention is necessary when used near children.

•Use only as described in this manual. Use only the manufacturer’s recommended attachments.

•Inspect the power cord regularly for damage, such as cracking, ageing, or damaged insulation.

Replace the power cord with the same type as original if any damage is found. Do not use with

damaged cord or plug.

•Use a defoamer any time you get foam in the recovery tank, to prevent motor damage.

•If foam or liquid comes out of the vacuum motor or exhaust, turn the machine off immediately.

•If the machine is not working as it should, has been dropped, damaged, left outdoors or flooded

with water, return it to a service center.

•Do not pull the machine by the cord, do not use the cord as a handle, close a door on the cord,

or pull the cord around sharp edges or corners. Do not run the machine over the cord. Keep

the cord away from heated surfaces. To unplug, grasp the plug, not the cord.

•Do not handle the plug, the cord, or the machine with wet hands.

•Extension cords must be 12/3 and no longer than 50 feet. Replace the cord or unplug

immediately if the ground prong becomes damaged.

•Do not put any object into openings. Do not use with any opening blocked; keep free of dust,

lint, hair, and anything that may reduce air flow.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes,

or any health endangering dusts. Do not use to pick up flammable or combustible liquids such

as gasoline or use in areas where they may be present.

•Use extra care when cleaning on stairs.

•Connect to a properly grounded outlet only.

•Liquid pumped out could be dangerous because of temperature, pressure, or chemical content.

•Do not let the pump run dry. If you run out of water, turn the machine off and refill

INSPECTION:

Carefully unpack and inspect your MX 521 H for shipping damage. Each machine is tested and inspected

before shipping. Any shipping damage incurred is the responsibility of the carrier. You should notify the

carrier immediately if you notice damage to the box or to the machine or parts.

CLEANING SOLUTIONS:

We recommend liquid cleaning chemicals. Powder chemicals may be used, but unless mixed very

thoroughly they could cause a build-up in the pump, lines, heat exchanger and/or quick disconnects. Any

problem caused by a chemical build-up is not covered by warranty. Use a neutral cleaner with a pH

between 6 and 9 to avoid premature wear of the pump, seals, and/or other components. Damage

caused by the use of strong chemicals is not covered by the warranty.

MAINTENANCE:

For optimum performance flush the machine with clear water at the end of each working day. Once a

month, minimum, run a flushing compound through the machine to break up any mineral or chemical

build-up that may have formed. Lubricate the wheels, castors, and quick disconnects with an all purpose

silicone spray. The vacuum and the pump do not require any maintenance. Clean the body with an all

purpose detergent, and protect it with an automobile interior polish.

Record the serial number and model of your new extractor here:

Serial Number: __________________

Model: MX 521 H__

Purchase Date:________________

Write the name and phone number of your

distributor:

_____________________________________

SWITCH

TURNS THE

HEATERON

1VACUUM

ON/OFF SWITCH

PUMP

ON/OFF

SWITCH

SELECT CARPET

ORUPHOLSTERY

(andbe sureto registeryour warranty)

REDLIGHT

INDICATES

THEHEATER

ISHEATING

11-600205211REVA

1 Inspect the machine, hoses, and cleaning tools for cleanliness and completeness.

2Fill the solution tank with water. Using warm water may be a benefit in cleaning effectiveness,

but do not use hot water (above 54

C / 130

F) in the tank.

3 Plug in the power cord.

NOTE: the red light (1) will turn on only when the heat exchanger is actively heating.

4 Connect the priming hose to the solution outlet quick disconnect on the machine, turn ON the pump

switch (4) and prime the air out of the pump by allowing the water to flow unrestricted. When the

water is clear (no air in it) and flowing smoothly, turn the pump switch OFF. Once the pump has

stopped, remove the priming hose. NOTE: Never remove the priming hose if the pump is still

running. To prime the pump, the solution tank should be full of liquid. Priming may take 20-60

seconds.

5 If desired add liquid cleaning chemical, with a pH between 6 and 9, to the solution tank. Mix well.

6 Attach the solution hose on the reel to the solution quick disconnect, and connect the vacuum hose

from the center of the reel to the hose barb on machine. Refer to the diagram above.

the recovery tank. Pull the hoses out of the reel. Attach the other ends of the hoses to the

cleaning tool.

OPERATION

Recovery

Tank Lid

Switch

Plate

Vacuum Hose Cuff

Solution Hose

Connection

Latch

Wheel

Castor

Solution Tank Lid

Dump Hose

Vaccum

inlet to tank

Recovery

Tank

Solution

Tank

GET FAMILIAR WITH YOUR NEW EXTRACTOR

11-600205211REVA

7 Allow the heat exchanger two minutes to reach operating temperature. The red light (1) will go

out when the heater has reached maximum operating temperature. The light will be ON most of

the time while you are cleaning.

8 Turn the pump ON (4) and set the pressure selection switch (3) to the desired spraying pressure:

Carpet at 300 PSI or Upholstery at 50 PSI.

9 Turn the vacuum ON (2). The motor will start slowly. This will increase the life of the motor and

prevent a large current surge from tripping the circuit breaker in the wall.

10 Begin cleaning using the correct hoses and tool.

11 Use defoamer in the recovery tank any time foaming occurs.

12 Monitor the water level in the solution tank. Do not let the pump run dry.

13 When the solution tank gets low, turn the pump and the vacuum off (3 & 4), fill the solution tank,

empty and clean the recovery tank.

14 When finished with the job, remove any unused solution from the solution tank by vacuuming it

into the recovery tank. Run a few gallons of clean water through the system.

15 Drain the recovery tank by placing the dump hose over a drain, or into a bucket, and remove the

hose cap.

16 Disconnect the hoses from the cleaning tool, and reel the hoses up onto the hose spool.

NOTE: to remove the reel, with the hoses, from the machine, pull the vacuum hose loose from the

hose barb on the front of the tank. Disconnect the solution hose quick coupling. Push the vacuum

hose into the center of the spool. Grasp the spool on both sides, and lift it off the machine. NOTE:

before servicing any component in the base cabinet, the hoses and spool must be removed from the

machine before the tanks can be lifted open.

CAUTION: to avoid vacuum motor damage, always use a defoamer any time foam is present.

BALL FLOAT VACUUM SHUT-OFF:

Prior to using the machine, always check that the float filter is clean and the ball can travel freely.

When the recovery tank is full, the ball float will rise and will shut off the vacuum flow to prevent any

more water from entering the tank. Turn off the vacuums, and empty the recovery tank.

NOTE: if foam is present, or if the ball float is prevented from rising, the float will not be able to stop

the air flow, and the tank may over fill. Water damage to the vacuum motors is not covered by

warranty.

CAUTION:if foam or water comes out the vacuum exhaust, turn

the machine off immediately

11-600205211REVA

20 December 2007

MX 521 H

212°F

III

Nilfisk Label

11-600205211REVA

MX 521 H EXTRACTOR

PART LIST

220 - 240V

1 1 600752101 Reel with hoses

2 1 600752102 Fuse kit

3 1 600752103 Switch kit

4 1 600752104 Ball float, vac inlet kit

5 1 600752105 Drain hose kit

6 1 600752106 Recovery Tank

7 1 600752107 Switch plate

8 1 600752108 Vacuum kit

9 1 600752109 Pump and motor, complete

10 1 600752110 Pump complete, no motor

12 1 600752112 Base kit

13 2 600752113 Latch kit

15 1 600752115 Power cord kit, EU plug

600752128 Power cord kit, UK plug

16 1 600752116 Reel Glide kit

17 1 600752117 Holding tank

18 1 600752118 Louver kit

19 1 600752119 Castor kit

20 1 600752120 Heat repair kit

21 1 600752121 Wheel kit

22 1 600752122 Lid kit

23 1 600752123 Heat exchanger replacement kit, 2000W

25 1 600752125 Quick disconnect, male

26 1 600752126 Gasket, base

27 1 600752127 Priming hose

29 1 600752129 Filter kit, pump and vacuum

31 1 600752131 RFI filter

32 1 600752132 Control board, vacuum motor

33 1 600752133 Label kit

ITEM QTY PART No. DESCRIPTION

MISCELLANEOUS PARTS AND KITS

600752130 Pump rebuild kit

20 December 2007

11-600205211REVA

TROUBLE SHOOTING:

IF THIS OCCURS CHECK THIS

Solution tank is empty.

Clogged spray tip.

Pump not running or not primed.

Valve on wand not operating.

Debris is plugging cleaning tool or vacuum hose.

Drain gate is not completely closed, or seals are damaged.

Vacuum dome is not seated or is damaged.

No power to motor.

Test the switch.

Test the vacuum motor.

Test the Vacuum Circuit Board.

Spraying too long. Try spraying for 10 - 12 seconds, or about three strokes.

Heat exchanger needs to be flushed.

Wrong tool being used. Too much water passing through. Longer hose or larger

diameter hose, than standard.

Heat is not turned on.

No power in the wall outlet - check to see if the breaker has tripped.

Check to see if the fuse has blown.

No power to the heat switch - check wiring for ‘opens.”

No power out of heat switch, follow troubleshooting steps to isolate the problem.

Call your distributor for additional help.

NO HEAT

ALWAYS UNPLUG THE MACHINE BEFORE

DISCONNECTING OR CONNECTING ANY

WIRES OR COMPONENTS.

Ifyou areunable to diagnose the problem, contact thecompany fromwhom youpurchased your MX521 H

MAINTENANCE SCHEDULE

CLEANALLFILTERS X

FLUSH OUT with DESCALER

DAILY

WEEKLY

MONTHLY

OTHER

CHECK POWER CORD

REPLACE VAC MOTOR BRUSHES

YEARLY

Around1500 hours

REPLACE PRESSURE REGULATOR

REPLACE VAC MOTOR BRUSHES

Around1500 hours

Or as needed

NO SPRAY

LOW SUCTION

NO SUCTION

LOW HEAT

11-600205211REVA

SPECIFICATIONS:

Rotomolded Body:

Power:

Vacuum at Nozzle:

Pump:

Heat Exchanger:

Weight:

Dimensions:

Lifetime Warranty

3220 W

30.4 KPA

21 Bar / 300 psi

2000 Watts

59.3 Kg

91 H x 45 W x 97 L cm

MX 521 H

600205299 CARPET WAND

11-600205211REVA

NOTES:

MX 521 H

EXTRACTOR

220 - 240V

Inhaltsverzeichnis

Sprachen:

Andere Nilfisk-Advance Schrubber Handbücher

Nilfisk-Advance

Nilfisk-Advance SCRUBTEC 545B Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance BA 450 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Advance SC901 ST-28D Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance BR 752 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance ROS1300 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Captor 5400 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Focus II Rider Installations- und Benutzerhandbuch

Nilfisk-Advance

Nilfisk-Advance Liberty SC60 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Advance SC370 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Liberty SC50 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Advance BR 1100S Bedienungs- und Montageanleitung

Nilfisk-Advance

Nilfisk-Advance BR 1000 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Liberty SC50 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SC500 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SC450 Stücklistenhandbuch

Nilfisk-Advance

Nilfisk-Advance Spintec 551 UH Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance C446 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance 908 7144 020 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Advance SC5000 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance 1300 LPG Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Micromax 17B Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Cr 1100 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance 9087331020 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance 56390926(850SC) Bedienungsanleitung

Beliebte Schrubber Handbücher anderer Marken

Olympus

Olympus M200H Bedienungsanleitung

Clarke

Clarke BEXT 100H Installations- und Betriebsanleitung

JOHNY VAC

JOHNY VAC JVC70BCT Bedienungsanleitung

RCm

RCm Elan Series Handbuch

Kärcher

Kärcher B 120 W Bedienungsanleitung

Truvox

Truvox Orbis MotorScrubber 20 Bedienungsanleitung

Numatic

Numatic TTB 4045/100 Bedienungsanleitung

U.S. Products

U.S. Products PEX 500-C-TICK Betriebsanleitung

Mclennan

Mclennan C510 Bedienungsanleitung

Tennant

Tennant T20 LPG Bedienungsanleitung

Columbus

Columbus ARA 66 BM 100 Bedienungsanleitung

Numatic

Numatic TTV 678G / 300T Bedienungsanleitung

American-Lincoln

American-Lincoln 505-945 Bedienungsanleitung

FIORENTINI

FIORENTINI ET 65-75 Bedienungsanleitung

Floorpul

Floorpul ruby 48 blt Benutzerhandbuch

Onyx

Onyx RX-34 Bedienungsanleitung

Dustbane

Dustbane Hurricane 400 Bedienungsanleitung

Sana

Sana EUJ-702 Bedienungsanleitung