Nilfisk-Advance Advance SC901 ST-28D Bedienungsanleitung

Advance Models:

56115530 (SC901 ST-28D)

56115531 (SC901 ST-34D)

56115532 (SC901 ST-32C)

SC901 ST

Instructions for use Instructions for Use

Original Instructions

Instrucciones de uso

Mode d’ emploi

3/2019 revised 4/2019 REV B

Form no. 56091217

A-English

B-Español

C-Français

A - 2 SC901 ST - 56091217 3/2019

INSTRUCTIONS FOR USEA - ENGLISH

TABLE OF CONTENTS

Page

Introduction..............................................................................A-3

Parts and Service ....................................................................A-3

Nameplate ...............................................................................A-3

Unpacking the Machine...........................................................A-3

Cautions and Warnings ...........................................................A-4

Know Your Machine....................................................... A-6 – A-7

Control Panel...........................................................................A-8

Control Panel – EcoFlex™ ......................................................A-8

Preparing the Machine for Use

Batteries ...................................................................... A-9 – A-10

Installing the Brushes ................................................ A-11 – A-12

Filling the Solution Tank.........................................................A-13

Squeegee Installation............................................................A-13

Detergent System (EcoFlex™).................................. A-14 – A-15

Operating the Machine

Wet Scrubbing........................................................... A-16 – A-17

After Using the Machine ........................................................A-18

Maintenance Schedule..........................................................A-19

Servicing the Vacuum Motor..................................................A-19

Lubricating the Machine ........................................................A-19

Maintenance

Charging the Batteries (Wet).................................................A-20

Charging the Batteries (Gel)..................................................A-20

Servicing the Squeegee ........................................................A-21

Adjusting the Squeegee ........................................................A-21

Troubleshooting.....................................................................A-22

Technical Speciﬁcations ........................................................A-23

Material Composition.............................................................A-24

3/2019 A - 356091217 - SC901 ST

ENGLISH - AINSTRUCTIONS FOR USE

INTRODUCTION

This manual will help you get the most from your Advance™ automatic scrubber/dryer. Read it thoroughly before operating the machine.

Note: Bold numbers in parentheses indicate an item illustrated on pages A-6 – A-8 unless otherwise noted.

This product is intended for commercial use only.

PARTS AND SERVICE

Repairs, when required, should be performed by your Authorized Advance Service Center, who employs factory trained service personnel, and

maintains an inventory of Advance original replacement parts and accessories.

Call Advance for repair parts or service. Please specify the Model and Serial Number when discussing your machine.

MODIFICATIONS

Modi¿cations and additions to the cleaning machine which affect capacity and safe operation shall not be performed by the customer or user

without prior written approval from Nil¿sk Inc. Unapproved modi¿cations will void the machine warranty and make the customer liable for any

resulting accidents.

NAMEPLATE

The Model Number (also known as Part Number) and Serial Number of your machine are shown on the Nameplate in the battery compartment.

This information is needed when ordering repair parts for the machine. Use the space below to note the Part Number and Serial Number of your

machine for future reference.

PART NO. ______________________________________

SERIAL NO. ____________________________________

UNPACKING THE MACHINE

When the machine is delivered, carefully inspect the shipping packaging and the machine for damage. If damage is evident, save the shipping

carton (if applicable) so that it can be inspected. Contact the Advance Customer Service Department immediately to ¿le a freight damage claim.

Refer to the unpacking instruction sheet included with the machine to remove the machine from the pallet.

REGULATORY

FCC:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

Users are not permitted to make changes or modify the device in any way. Changes or modi¿cations not expressly approved by Nil¿sk,

Inc. will void the user’s authority to operate the equipment.

IC:

This device complies with Industry Canada ICES-002. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired

operation of the device.

revised 4/2019

A - 4 SC901 ST - 56091217 3/2019

INSTRUCTIONS FOR USEA - ENGLISH

CAUTIONS AND WARNINGS

SYMBOLS

Advance uses the symbols below to signal potentially dangerous conditions. Read this information carefully and take the

necessary steps to protect personnel and property.

DANGER!

Is used to warn of immediate hazards that will cause severe personal injury or death.

WARNING!

Is used to call attention to a situation that could cause severe personal injury.

CAUTION!

Is used to call attention to a situation that could cause minor personal injury or damage to the machine or other property.

Read all instructions before using.

GENERAL SAFETY INSTRUCTIONS

Speciﬁc Cautions and Warnings are included to warn you of potential danger of machine damage or bodily harm.

This machine is for commercial use, for example in hotels, schools, hospitals, factories, shops and ofﬁces other than

normal residential housekeeping purposes.

WARNING!

•This machine should only be used by properly trained and authorized persons.

•This machine is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning

use of the machine by a person responsible for their safety.

•Children should be supervised to ensure that they do not play with the machine.

•Close attention is necessary when used near children.

•While on ramps or inclines, avoid sudden stops. Avoid abrupt sharp turns. Use low speed down ramps.

•Keep sparks, ﬂame and smoking materials away from batteries. Explosive gases are vented during normal operation.

•Charging the batteries produces highly explosive hydrogen gas. Charge batteries only in well-ventilated areas, away

from open ﬂame. Do not smoke while charging the batteries.

•Remove all jewelry when working near electrical components.

•Turn the key switch off (O) and disconnect the batteries before servicing electrical components.

•Never work under a machine without safety blocks or stands to support the machine.

•Do not dispense ﬂammable cleaning agents, operate the machine on or near these agents, or operate in areas where

ﬂammable liquids exist.

•Do not clean this machine with a pressure washer.

•Only use the brushes provided with the appliance or those speciﬁed in the instruction manual. The use of other

brushes may impair safety.

•Observe the Gross Vehicle Weight, GVW, of the machine when loading, driving, lifting or supporting the machine.

3/2019 A - 556091217 - SC901 ST

ENGLISH - AINSTRUCTIONS FOR USE

CAUTIONS AND WARNINGS - CONTINUED

CAUTION!

•This machine is not approved for use on public paths or roads.

•This machine is not suitable for picking up hazardous dust.

•Use care when using scariﬁer discs and grinding stones. Advance will not be held responsible for any damage to

ﬂoor surfaces caused by scariﬁers or grinding stones.

•When operating this machine, ensure that third parties, particularly children, are not endangered.

•Before performing any service function, carefully read all instructions pertaining to that function.

•Do not leave the machine unattended without ﬁrst turning the key switch off (O), removing the key and securing the

machine.

•Turn the key switch off (O) and remove the key, before changing the brushes, and before opening any access panels.

•Take precautions to prevent hair, jewelry, or loose clothing from becoming caught in moving parts.

•Use caution when moving this machine in below freezing temperature conditions. Any water in the solution, recovery

or detergent tanks or in the hose lines could freeze, causing damage to valves and ﬁttings. Flush with windshield

washer ﬂuid.

•The batteries must be removed from the machine before the machine is scrapped. The disposal of the batteries

should be safely done in accordance with your local environmental regulations.

•Do not use on surfaces having a gradient exceeding that marked on the machine.

•All doors and covers are to be positioned as indicated in the instruction manual before using the machine.

•Refer to the battery charger OEM product manual for additional speciﬁc battery charger warnings.

SAVE THESE INSTRUCTIONS

A - 6 SC901 ST - 56091217 3/2019

INSTRUCTIONS FOR USEA - ENGLISH

KNOW YOUR MACHINE

As you read this manual, you will occasionally run across a bold number or letter in parentheses - example: (2). These numbers refer to an item

shown on these pages unless otherwise noted. Refer back to these pages whenever necessary to pinpoint the location of an item mentioned in

the text. NOTE: Refer to the service manual for detailed explanations of each item illustrated on the next 3 pages.

1 Solution Tank Fill

2 Operator Control Handle

3 Bottle Holder / Squeegee hanger location

4 Vacuum Motor Shutoff Float

5 Debris Tray

6 Recovery Tank Lid

7 Recovery Tank (Detergent Cartridge Access Cover)

7a Detergent Cartridge (EcoFlex models only)

7b Detergent Module (EcoFlex models only)

8 Scrub Deck (Disc models)

9 Brush Housings (include Bristle Skirt)

10 Scrub Deck Bumper Wheel

11 Drive Wheel

12 Squeegee Assembly

13 Solution Filter

14 Solution Shut-off Valve

15 Battery Pack Connector

16 Brush Motor Circuit Breakers (30 Amp)

17 Vacuum Fan Circuit Breaker (20 Amp)

18 Wheel Drive Circuit Breaker (30 Amp)

19 Key Switch Circuit Breaker (2.5 Amp)

3/2019 A - 756091217 - SC901 ST

ENGLISH - AINSTRUCTIONS FOR USE

KNOW YOUR MACHINE

2 Operator Control Handle

20 Solution Manifold (Cylindrical Models Only)

21 Idler Assembly (Cylindrical Models Only)

22 Debris Hopper (Cylindrical Models Only)

23 Forward / Reverse Drive Paddle

24 Onboard Battery Charger (Not found on all models)

25 Solution Control

26 Speed Limit Control Knob

27 Battery Hour Gauge

28 Water proof Key Switch

29 Recovery Tank Drain Hose

30 Squeegee Raise / Lower Lever

31 Solution Drain Hose / Level Indicator

32 Scrub Deck Raise / Lower Lever

33 Squeegee Mount Thumb Nut

34 Recovery Hose

35 Squeegee Blade Tension Strap

36 Squeegee Blade Alignment Pins

37 Squeegee Blade Latch

37 36 35

A - 8 SC901 ST - 56091217 3/2019

INSTRUCTIONS FOR USEA - ENGLISH

CONTROL PANEL

A Key Switch (Main Power)

B Speed Control Knob

C Forward / Reverse Drive Paddle

D Operator Control Handle

E Solution Control (ST Models)

F Battery / Hour Gauge

The non-resettable Hour Gauge displays the running total of hours accumulated on the scrub motors up to 99,999 hours.

The hour glass symbol ﬂashes on/off to indicate time counting.

CONTROL PANEL – ECOFLEX

G Detergent Module (EcoFlex models only)

H Solution Flow Control Knob (EcoFlex models only)

J Detergent System Control Knob (EcoFlex models only)

K Burst of Power Switch (EcoFlex models only)

L Burst of Power Switch LED (EcoFlex models only)

3/2019 A - 956091217 - SC901 ST

ENGLISH - AINSTRUCTIONS FOR USE

BATTERIES

If your machine shipped with batteries installed do the following:

 Check that the batteries are connected to the machine (15).

Turn ON the Key Switch (A) and check the Battery / Hour Gauge (F). Battery Charge capacity is indicated using a 10 segment LED bar

graph display from full (right LED segment lit) to empty (left LED segment lit). LED Flash Alert™ ﬂashes the 2nd LED from the left as a

warning that the battery has discharged 70%.

At 80% discharge, LED Flash Alert™ alternately ﬂashes the left 2 LEDs to indicate very low capacity is remaining. At this level the scrub

systems are disabled to protect the battery. The vacuum system will continue to operate to allow recovery of any solution remaining on ﬂoor.

 IMPORTANT!: BATTERIES SHOULD BE FULLY CHARGED BEFORE EACH USE. SEE THE “CHARGING THE BATTERIES”

SECTION.

 IMPORTANT!: IF YOUR MACHINE HAS AN ONBOARD BATTERY CHARGER REFER TO THE OEM PRODUCT MANUAL FOR

INSTRUCTIONS REGARDING SETTING THE CHARGER FOR BATTERY TYPE.

If your machine shipped without batteries installed do the following:

 Consult your Authorized Advance dealer for recommended batteries.

 Install the batteries by following the instructions below.

 DO NOT install three 12 volt batteries in your machine. This affects the stability of the machine.

 IMPORTANT!: IF YOUR MACHINE HAS AN ONBOARD BATTERY CHARGER REFER TO THE OEM PRODUCT MANUAL FOR

INSTRUCTIONS REGARDING SETTING THE CHARGER FOR BATTERY TYPE.

WARNING!

Use extreme caution when working with batteries. Sulfuric acid in batteries can cause severe injury if allowed to contact the skin

or eyes. Explosive hydrogen gas is vented from the batteries through openings in the battery caps. This gas can be ignited by

any electrical arc, spark or ﬂame. Do not install any lead-acid battery in a sealed container or enclosure. Hydrogen gas from

overcharging must be allowed to escape.

When Servicing Batteries...

*Remove all jewelry

*Do not smoke

*Wear safety glasses, rubber gloves and a rubber apron

*Work in a well-ventilated area

*Do not allow tools to touch more than one battery terminal at a time

*ALWAYS disconnect the negative (ground) cable ﬁrst when replacing batteries to prevent sparks.

*ALWAYS connect the negative cable last when installing batteries.

CAUTION!

Electrical components in this machine can be severely damaged if the batteries are not installed and connected properly. Advance, a

qualiﬁed electrician, or the battery manufacturer should install batteries.

When changing batteries or the charger, please contact your local authorized service center for correct battery, charger and machine

settings to prevent battery damage.

A - 10 SC901 ST - 56091217 3/2019

INSTRUCTIONS FOR USEA - ENGLISH

BATTERIES (CONTINUED)

1 Remove the batteries from their shipping crate and carefully inspect them for cracks or other damage. If damage is evident, contact the

carrier that delivered them or the battery manufacturer to ﬁle a damage claim.

2 Turn the Master Key Switch (A) OFF and remove the key.

3 Tip the recovery tank to the side, locked position. Remove the battery cables from inside the battery compartment.

4 Your machine comes from the factory with enough battery cables to install six 6 volt batteries. Carefully lift the batteries into the battery

compartment and arrange them exactly as shown in Figure 1. Secure the batteries as close to the back of the machine as possible.

NOTE: Battery spacers (O) need to be installed between the bottom of the batteries and the short wall on the bottom of the tank to create

more space between the batteries and prevent the Deck Lever Arm (P) from hitting the batteries.

5 Install the battery cables as shown. Position the cables so the battery caps can be easily removed for battery service. To prevent

interference, route the cable (Q) over the top of the Deck Lever Arm (P) as shown in Figure 1.

IMPORTANT!: The protective caps supplied with the batteries need to be left on or re-used to completely cover the

portion of the battery terminals that are not being protected by the battery cable terminal cover boots supplied with the

battery cables. This also applies to the inline fuse holder boot.

6 Carefully tighten the nut in each battery terminal until the terminal will not turn. Do not over-tighten the terminals, or they will be very difﬁcult

to remove for future service.

7 Coat the terminals with spray-on battery terminal coating (available at most auto parts stores).

8 Put one of the rubber terminal cover boots over each of the terminals and connect the Battery Pack Connector (15).

9 Make sure the Fuse Holder Boot (R) is covering the fuse holder, the cable end of the Battery Pack Connector (15), and as much of the battery

terminal as possible. Leave the protective caps supplied with the batteries in place or re-use to cover the terminal areas not protected by the

terminal cover boots.

FIGURE 1

310AH @ 20HR RATE

BATTERY SPACER

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Nilfisk-Advance Schrubber Handbücher

Nilfisk-Advance

Nilfisk-Advance SC530 Stücklistenhandbuch

Nilfisk-Advance

Nilfisk-Advance crescent SC250 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SR 1101 B Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Nilfisk Smart Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SC6500 Stücklistenhandbuch

Nilfisk-Advance

Nilfisk-Advance SC6000 36C Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Advance SC370 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SC6000 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance 48 LPG Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance ROS1300 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance BA 340 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Captor 4300 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SC351 Benutzerhandbuch

Nilfisk-Advance

Nilfisk-Advance SelectScrub KA-27 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SC351 Benutzerhandbuch

Nilfisk-Advance

Nilfisk-Advance Spintec 551 UH Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW8000 Installations- und Benutzerhandbuch

Nilfisk-Advance

Nilfisk-Advance Adgressor BR 1050S Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Scrubtec 334 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance AX 651 Combi EDS Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Liberty SC60 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Liberty SC50 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance AquaRide Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance FLOORTEC R 670 B Bedienungsanleitung

Beliebte Schrubber Handbücher anderer Marken

Olympus

Olympus M200H Bedienungsanleitung

Clarke

Clarke BEXT 100H Installations- und Betriebsanleitung

JOHNY VAC

JOHNY VAC JVC70BCT Bedienungsanleitung

RCm

RCm Elan Series Handbuch

Kärcher

Kärcher B 120 W Bedienungsanleitung

Truvox

Truvox Orbis MotorScrubber 20 Bedienungsanleitung

Numatic

Numatic TTB 4045/100 Bedienungsanleitung

U.S. Products

U.S. Products PEX 500-C-TICK Betriebsanleitung

Mclennan

Mclennan C510 Bedienungsanleitung

Tennant

Tennant T20 LPG Bedienungsanleitung

Columbus

Columbus ARA 66 BM 100 Bedienungsanleitung

Numatic

Numatic TTV 678G / 300T Bedienungsanleitung

American-Lincoln

American-Lincoln 505-945 Bedienungsanleitung

Floorpul

Floorpul ruby 48 blt Benutzerhandbuch

Onyx

Onyx RX-34 Bedienungsanleitung

Dustbane

Dustbane Hurricane 400 Bedienungsanleitung

Sana

Sana EUJ-702 Bedienungsanleitung

REMS

REMS Twist Bedienungsanleitung