Nissin Digital Di700A Bedienungsanleitung
for Fujifilm cameras
INSTRUCTION MANUAL
Thank you for purchasing a Nissin product
Before using this flash unit, please read this instruction manual and
refer your camera owner’s manual carefully to get a better
understanding of the proper operation to enjoy flash photography.
Nissin Di700A type Fujifilm is designed for Fujifilm digital SLRs, with the latest
TTL flash control system. Please note that Di700A Fujifilm are not usable with
other branded cameras for TTL operation.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Please refer Nissin’s compatibility chart shown at its home page for details and
recent updates: http://www.nissin-japan.com or http://www.nissindigital.com
SPECIAL FEATURES
The Di700A features the use of a selector dial to quickly move through all settings
and can be easily operated by one finger-tip.
The Di700A with wireless flash shooting using Nissin Air System/ radio
transmission.
Flash protection function:
When the red LED lamp starts blinking, it means that flash is overheating.
The LED turns red when charging.
When the LED lamp turns green, the flash is charged and you can start to shoot.
Compatible cameras
1
Remark: Nissin Air System (NAS) is designed for Nissin flash and
Nissin commander.
These safety instructions refer to important information on how to use this
product safely and properly. Please read the following instructions before
using the product.
SAFETY INSTRUCTIONS
WARNING
The flash unit contains high voltage electric parts. Do not try to open or repair the flash
unit. Return it back to the repair service station or the store where you bought it from.
Do not touch the inside parts from the opening when the unit was dropped or broken.
Do not shoot the flash directly to the eyes at short distance. It may damage the eyes.
When taking a flash picture, especially toward a baby, it is recommended to keep the
flash unit at least 1 meter (3.3feet) away from the subject. Or use diffuser or bounce the
light to the ceiling or wall to soften its intensity.
Do not place the flash unit near any flammable gas, chemicals or such liquids. It may
cause fire or electric shock.
Do not touch the flash unit with wet hands or use in the water. The flash unit carries high
voltage inside and it may cause an electric shock.
Do not shoot the flash unit directly at the driver of automobiles or such vehicles.
Do not set the flash window close to the human body and shoot, which may get scalded.
Place the batteries correctly in position. Placing the batteries in wrong polarity may
cause leakage, exothermic heat or explosion.
CAUTIONS
Do not leave or store the flash unit in the temperature over 40ºC/ 104ºF, such as in the
automobile.
The flash unit is not water resistance. Keep the unit away from rain, snow and humidity.
Do not use benzene, thinner or other alcoholic agents to clean the unit.
Do not use this flash unit with cameras which are not recommended in the compatibility
list at official website, otherwise it may damage the camera’s circuitry.
Remove the batteries when not in use for a longer period of time.
Do not have a heavy impact to the flash unit, nor throw it onto a hard surface floor.
When using the external power pack, read the safety instructions carefully and follow the
operation manual.
This symbol refers to the possibility of personal injury, death or property
damage if not followed as described.
This sign refers to conditions which may cause damage or defect.
2
Names of the Components
Flash stand
Accessories: Flash stand, Pouch
7
3
6
5
4
2
8
17
10
11
12 13 14
9
18
16
15
1 Fill-in reflector
2 Light diffusing panel
3 Flash head
4 Remote/ Slave sensor
5 AF-assist light
6 Mounting foot
7 Hotshoe contacts
8 Power Pack socket
9 Display screen
10 Select dial
11 Set button
12 Release button
13 Pilot button (Test flash button)
14 On/Off switch (System lock button)
15 3.5mm sync socket
16 X-terminal
17 Battery magazine BM-02
18 Rotate lock
1
3
Inserting batteries
1. Remove the battery magazine and insert
4 x size AA batteries as shown in the
picture.
2. The battery compartment is specially
designed so that every battery is placed in
the same direction to avoid confusion in
poor lighting conditions.
3. +/- symbol is clearly marked in the battery
compartment.
4. Place the battery magazine back into the
body.
When the recycle time becomes longer
than 30 seconds, replace the batteries with
fresh ones or recharge the batteries (re-
chargeable batteries).
NOTE
It is recommended to use all 4 batteries of the same brand and type, and
replace them all at the same time.
Wrong insertion of each battery would not make electric contact.
Usable batteries - Alkaline batteries, Lithium batteries or NiMH batteries.
Basic Operation
4
Di700A has an energy saving power off function
Reset setup Option
To save battery energy, the power is automatically turned off (switch
to stand-by mode), in A mode, TTL mode & Manual Power mode, in
about 2 minutes of idle use; in SD mode, SF mode, in about 5
minutes of idle use.
While Di700A is in the stand-by mode a Pilot button blinks every 2
seconds showing the flash unit is in stand-by mode. To turn on
Di700A again, press the camera’s shutter button halfway or press
any button of the flash unit.
In case Di700A is not in use for over 60 minutes, the unit is
completely turned off.
To turn on Di700A again hold On/Off switch for 1 second.
Press the Set button for 5 seconds to reset the setup menu
The flash will be automatically reset to the factory default “A” mode.
Basic Operation
5
Mounting Di700A on the camera
Removing Di700A from the camera
Press the unlock button and slide the mounting
foot of Di700A off the hotshoe of the camera.
Slide the mounting foot of Di700A into the
hotshoe of the camera.
Make sure that the mounting foot will lock
(with a “click”) when it has been inserted
completely.
1.
2.
2
1
6
Turn on the flash unit
For a test flash, press the Pilot button.
When using the test flash as an open flash,
please note that the reference guide number
in this case is G.No.10 (ISO 100).
To turn off the flash unit manually, press the On/Off
switch for 1 second.
Press the On/ Off switch and Pilot
button turns red, showing the unit is
turned on.
In a few seconds, the Pilot button
turns green. The Di700A is ready to
shoot.
MENU SCREEN
Di700A Flash Mode and Functions
Flash light is fully controlled by the camera for
the most proper exposure.
Full Automatic Mode
TTL Program Mode
Manual Setting Mode
Slave Digital
Slave Film
…
…
…
…
…
…
Flash light is automatically controlled by the
camera but the flash exposure value can be
compensated.
Manual Mode -Selecting the desired manual
power on the flash unit.
Using a Nissin Flash (master/ slave) with a NAS shooting function makes it easy to shoot with
advanced wireless multiple flash lighting, in the same way as normal autoflash shooting.
Wireless Remote Mode - Radio Transmission (NAS)
Rotate the dial to select a function.
Set
*For details on setting the master unit functions, see the Nissin commander’s instructions.
NAS
7
Shooting Di700A automatically
Set Di700A to the camera’s hotshoe and press the on/off switch to
power on.
Rotate the dial to “A” mode then press the Set button.
Di700A is now set for the camera’s automatic flash control system.
Press the shutter button of your camera halfway to focus the subject.
Press the on/ off switch once again to lock this condition on your
flash. (Press it again to release the lock)
Take the picture. Di700A is fired and the result is immediately
shown on the camera’s LCD display.
When you change the focal length, the power zoom flash head of
Di700A responds without delay and immediately sets its position to
match the lens focal length you selected.
The flash illumination coverage of Di700A responds to the lens focal
length of 24mm to 200mm (16mm film camera standard).
In all of the camera's shooting modes listed above, Di700A will fully
work in TTL automatic-flash system.
Shutter speed, aperture and flash mark ( ) are indicated in cam-
era’s view finder.
(Program AE), (Aperture priority AE),
(Shutter priority AE) or (Manual Exposure);
S
8
Set the camera’s shooting mode, select focal length and take pictures
with Di700A on your camera.
Di700A is a supplement to help you in taking a creative and live
picture. Almost all tasks are automatically done by the camera and
you just control the camera only.
Synchro Terminal
Di700A is equipped with a Synchro terminal (X terminal) to connect
an off-camera cable. This allows photography with flash units
separate from the camera. This feature can be applied in Manual
mode only.
Mode Shutter
Speed
Aperture
Setting
Control on
the camera
Automatic Automatic Automatic
Manual Automatic
Automatic Manual
Manual Manual
Any available shutter
speed can be set
Any available f-stop
can be set
Any shutter speed / f-stop
combination can be set
[ P]
[ M]
[ S]
[ A]
9
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Nissin Digital Kamerablitz Handbücher
Nissin Digital
Nissin Digital MG60 Bedienungsanleitung
Nissin Digital
Nissin Digital i60A Bedienungsanleitung
Nissin Digital
Nissin Digital i600 Bedienungsanleitung
Nissin Digital
Nissin Digital NI-HI600M Bedienungsanleitung
Nissin Digital
Nissin Digital i400 Bedienungsanleitung
Nissin Digital
Nissin Digital MG60 Bedienungsanleitung
