Nitsuko TX Series Bedienungsanleitung

Nitsuko TX Series User Guide
Table Contents
Trunk Outgoing Call 1
Specified Trunk Access 1
Last Number Dialling (LND) 2
Saved Last Number Dialling (SLND) 3
Abbreviated Dialling 3
One Touch Dialling 4
Toll Restriction 5
Walking Toll Restriction 6
Dial Block 7
Flash 8
Pulse to Tone Conversion 8
Camp On (Trunk Queuing) 9
Key Touch Tone 9
Easy Trunk Access 10
Queuing Group Access 10
Automatic Repeat Dialling 11
Loop Key Trunk Access 12
Automatic Off Hook Trunk Access 12
Account Code 13
Trunk Incoming Call 14
Incoming Trunk Access 14
Trunk Off Hook Signalling 14
Ringing/Recall Trunk Off Hook Access 15
Night Service (Manual/Auto) 15
Call Forward 16
Follow Me 18
Call Pickup 19
Do Not Disturb 19
Executive DND 19
DISA (Extension Access) 20
Hold/Transfer/ uring Conversation 21
Hold 21
Music on Hold 22
External Music On Hold 23
Transfer 23
Park Hold (824/1232/2464) 26
Conference 26
Long Conversation Warning 29
Long Conversation Cut Off 29
Break In 29
Other Trunk Features 31
PBX Compatibility 31
Dial Mode (Tone/Pulse) Selection 31
Private Line 32
Tenant Service 32
Unsupervised Conference 33
Call Timer 33
DISA (Trunk to Trunk) 34
Intercom Outgoing Call 35
Intercom Link Increase 35
Intercom Call 35
Direct Station Select 36
Intercom Off Hook Signalling 37
Group Hunt 37
Step Calling 38
Camp On (Call back) 39
Message Waiting 39
Paging 41
Flexible Station Numbering 43
Dual Handsfree Hotline 44
Intercom Incoming Call 45
Intercom Answer 45
Call Pickup 45
Meet Me Answer Paging 46
Meet Me Conference Paging 46
Do Not Disturb 46
Intercom Hold 47
Intercom Call Transfer 48
Call Froward 48
Follow Me 48
Executive DND 49
Other Intercom Features 50
BGM (824/1232/2464) 50
External Paging 50
Doorphone 50
Door Lock Control 51
Room Monitor 52
DSS Console (1232/2464) 53
Alphanumeric isplay TEL Feature 57
Text Message 57
Time and Date 62
Name Storing (Trunk & Station) 63
Directory Dialling 64
Alarm Clock 65
Stopwatch 66
Busy Lamp Field 66
Other Features 67
Handsfree (Speaker & Microphone) 67
Lamp Shift Mode (824/1232/2464) 68
Remind Call on SLT 69
Station Message Detail Recording (SMDR) 69
Polarity Reverse Detection (1232/2464) 70
DISA with Audio Guidance 71
External Call Forward on DISA 71
One Touch Feature Access 72
Volume Control 73
DLS Console (824/1232/2464) 74
Headset Operation 75

Trunk Outgoing Call
Specified Trunk Access
escription:
Trunk (CO/PBX) lines can be group into a maximum of 30 groups. The line groups
assigned to each extension can be used for outgoing calls. Up to two outgoing line groups can
be assigned to an extension. An extension user can place outside calls on a particular line group
by pressing Line key or dialling line number.
Station Application:
KTS, SLT
Operation:
To make an outside call on a particular line:
<KTS>
When the trunk line appears under a Line key:
1. Lift handset or press SPK key.
2. Press a Line key. Hear dial tone.
3. Dial telephone number.
When the trunk line does not appear under a Line key:
1. Lift handset or press SPK key. (See note 1)
2. Dial 9 (824/1232/2464).
Dial 90 (308).
3. Dial two digit line number. Hear dial tone.
4. Dial telephone number.
<SLT>
1. Lift handset. Listen for dial tone.
2. Dial 0 or 9 (See note 2).
3. Dial two digit line number. Hear dial tone.
4. Dial telephone number.
Note: 1 If program #75 D is 0 (No Tone), press ICM key after step 1 to seize Intercom
(824/1232/2464).
Note: 2
Program #20 D Data Automatic Trunk Access Code for SLT Dial at Step 2
0 0 9
1 9 0
Note: 3 Easy Trunk Access, Queuing Group Access, Loop Key Trunk Access, Automatic Off
Hook Trunk Access features provide other ways to access a Trunk Line.

Related System ata:
#02: Line Group Assignment
#03 C: Common Use Line Assignment
#06: Outgoing Line Access
#75 D: KTS Off Hook Mode Selection
Single Step Access
escription:
Single Step Access allows a key telephone user to obtain outside or intercom dial tone
for an outgoing call in a single step, without lifting the handset or pressing the SPK key.
Station Application:
KTS
Operation:
To obtain dial tone using Single Step Access:
− Do not lift handset.
1. Press a Line key. The Line key and SPK key light.
− Dial tone comes over the speaker.
To obtain intercom dial tone using Single Step Access:
− Do not lift handset.
1. Press ICM key. ICM and SPK key light.
− Dial tone comes over the speaker.
Related System ata:
#15 E: Single Step Access.
Preselection
escription:
This feature permits access to a Trunk or ICM call by lifting the handset or pressing the
SPK key within three seconds of pressing a Line or ICM key.
Station Application:
KTS

Operation:
1. Press a Line or ICM key.
2. Lift handset or press SPK key within 3 seconds.
− Trunk Line or Intercom is seized.
Related System ata:
#15 E: Single Step Access.
Last Number ialling (LN )
escription:
The last telephone number dialled on an outgoing call (Trunk line) can be redialled. A
maximum of 18 digits are stored.
Station Application:
KTS, SLT
Operation:
<KTS>
1. Lift handset or press SPK key.
2. Press a Line key.
3. Press LND ley.
<SLT>
1. Lift handset.
2. Dial function code (See note 1).
3. Dial queuing group number (See note 2).
Note 1:
Program #20 D Data Automatic Trunk Access Code for SLT Dial at Step 2
Dial Plan 1 60
Dial Plan 2 0 0 94
1 9 04
Note 2: Queuing group numbers are 0 to 6 (0: Any Line, 1 6: Queuing group No).
Related System ata:
#08 B: SLT Dial Plan Set
#33: LND/Repeat Dial Hooking Time
#64 C: Trunk Line Seizing Order Selection

Saved Last Number ialling (SLN )
escription:
This feature permits saving the last number dialled for redialling at a later time. The
saved telephone number remains in memory until another is stored in its place.
Station Application:
KTS
Operation:
To place an outside call using saved last number:
1. Lift handset or press SPK key.
2. Press a Line key.
3. Press DC key and #
OR
Press One Touch key.
To store dialled number as saved last number:
1. While talking on trunk line.
2. Press DC key twice before terminating a call
OR
Press One Touch key before terminating a call.
To set One Touch key as SLN key:
1. Press SPK key.
2. Press ICM key. (824/1232/2464 Only) (See note 1)
3. Press DC key and (
4. Press One Touch key.
5. Press OPAC key and #
6. Press SPK key.
Note 1: If program #75 D is 0 (No Tone), skip step 2. (824/1232/2464).
Note 2: One Touch key #10 is set as SLND key initially.
Related System ata:
Not applicable.

Abbreviated ialling
escription:
The system provides common use abbreviated dialling. Abbreviated Dialling allows
storage of up to 100 or 200 locations 18 digit telephone number under 2 or 3 digit codes (00 to
99 or 000 to 199).
The user can select the storage quantity of Abbreviated Dial in Program #17 D.
Station Application:
KTS, SLT
Operation:
To place an outside call:
<KTS>
1. Lift handset or press SPK key.
2. Press an idle Line key.
3. Press DC key.
4. Dial abbreviated number (00 to 99) or (000 to 999).
<SLT>
1. Lift handset.
2. Dial function code (See note 1).
3. Dial queuing group number (0 to 6) (See note 2).
4. Dial abbreviated number (00 to 99) or (000 to 199).
Note 1:
Program #20 D Data Automatic Trunk Access Code for
SLT
Dial at Step 2
Dial Plan 1 5
Dial Plan 2 0 0 93
1 9 03
Note 2: Queuing group numbers are 0 6 (0: Any line, 1 6 Queuing group No).
To store abbreviated number (Extension 10 Only):
1. Press SPK key.
2. Press ICM key (824/1232/2464 only) (See note 1)
3. Press DC key and .
4. Dial abbreviated number (00 to 99) or (000 to 199)
5. Dial phone number to be stored (See note 2).
6. Repeat steps 3 to 5.
7. Press SPK key to exit form Abbreviated Dialling entry.

Note 1: If program #75 D is 0 (No Tone), skip step 2 (824/1232/2464).
Note 2: You can enter pauses (TRFR key), flashes (FLASH key) and stops (CONF key) when
storing a Abbreviated Dial Number. Each pause, stop or flash counts as a digit when totalling the
number of digits in a Abbreviated Dial Number. When stop is inserted, dialling will be stopped this
position and can be continued by dialling.
Related System ata:
#08 B: SLT Dial Plan Set
#17 D: Storage Quantity of Abbreviated Dial
#18 C: Abbreviated Dialling Restriction
One-Touch ialling
escription:
One Touch Dialling allows you to store ten of your most frequently called outside
numbers as personal abbreviated dial numbers at your extension so you can call them with just
a single touch. Dial number to be stored is up to 18 digits including pauses (TRFR key), flashes
(FLASH key) and stops (CONF key). The One Touch Dial numbers are stored under the ten
One Touch keys (No.1 to No.10) as F01 to F10.
When the number of common Abbreviated Dialling is set to 100 in Program #17 D, the
memory for the remaining 100 numbers can be used for personal abbreviated dial numbers at
10 key telephones. The assigned Key Telephone user can store up to 10 more numbers under
ten One Touch keys as F11 to F20. When dialling, the user must press OPAC key before
pressing an One Touch key.
Station Application:
KTS
Operation:
<ALL KTS>
To place an outside call:
1. Seize a Trunk line.
2. Press On e Touch key which stores desired phone number.

To store a One Touch ial number:
1. Press SPK key.
2. Press ICM key (824/1232/2464 only) (See note 1).
3. Press DC key and
4. Press a One Touch key to store a phone number.
5. Dial phone number to stored (One Touch Key No.1 to No.10 store numbers in F01
F10).
6. Repeat steps 3 to 5.
7. Press SPK key to exit from One Touch Dialling entry.
<Only assigned KTS>
To place an outside call:
1. Seize a Trunk line.
2. Press OPAC key.
3. Press One Touch key which stores the desired phone number.
To store a One-Touch ial number:
1. Press SPK key.
2. Press ICM key (824/1232/2464 only) (See note 1).
3. Press OPAC key.
4. Press DC key and
5. Press a One Touch key to store a phone number. (One Touch Key No.1 to No.10 store
numbers in F11 F20).
6. Dial phone number to be stored.
7. Go to Step 3 to enter another number.
OR
Hang up or press SPK to finish.
To check stored One-Touch ial number:
(On hook condition)
1. Press CHECH key.
2. Press SPK key.
3. Press DC key and OPAC key.
4. Press a One Touch key which stores the phone number.
5. Press CLEAR key to finish.
Note 1: If program #75 D is 0 (No Tone), skip step 2 (824/1232/2464).
Note 2: If the above operations are taken without pressing OPAC key, the numbers stores in F1
F10 are called.
Related System ata:
#17 D: Storage Quantity of Abbreviated Dialling.
#75 B: Personal Abbreviated Dial.

Toll Restriction
escription:
Toll Restriction determines extension’s ability to make calls. Each extension can be
assigned on of the following six classes per mode (Day/Night). Toll Restriction Class A is the
highest and the Class F is the lowest.
Class-A: No dialling restrictions.
Class-B: Dials are restricted by DATA B except dials matching PBX extension call or
DATA F.
Class-C: Dials are restricted by DATA D2 except dials matching PBX extension call,
DATA C, or DATA F.
Class- : Dials are restricted by DATA D2 or DATA D1 except dials matching PBX
extension call or DATA F.
Class-E: Dials are restricted all outgoing Trunk calls except dials matching PBX extension
call or DATA F.
Class-F: Intercom calls only.
The DATA (restricted/permitted codes and number length limit) within the Classes must be
entered in programming.
If there are PBX lies, PBX access code must be assigned in programming in order for Toll
Restriction to be properly applied.
Toll restrictions are not applied to lines programmed as Unrestricted Lines.
When the system is placed in night mode by Night Service feature, the Toll Restriction class
assignment for night mode is activated.
Station Application:
KTS, SLT
Operation:
When an extension user dials a call that is not allowed by the assigned Class, the system
automatically disconnects the line.

Related System ata:
#03 D: Unrestricted Lines
#18 C: Abbreviated Dialling Restricted
#35 A: Toll Restriction Class (Day)
#35 B: Toll Restriction Class (Night)
#36: Permitted Codes (Data C)
#37: Number Length Limit (DATA D1)
#38: PBX CO Access Codes (DATA E)
#39: Common Unrestricted Codes (DATA F)
#40: Class B Restricted Codes (DATA B)
#41: Class C/D Restricted Codes (DATA D2)
Walking Toll Restriction
escription:
Walking Toll Restriction lets you temporarily override an extension’s dialling
programmed security code at that extension. Dialling the code overrides the restrictions set up
in Toll Restriction.
Station Application:
KTS, SLT
Operation:
<KTS>
1. Lift handset.
2. Press an idle Line key.
3. Press OPAC key.
4. Press DC key.
5. Dial security code.
6. Dial phone number.
<SLT>
1. Lift handset.
2. Dial 07 (or 97). => (See note)
3. Dial security code.
4. Dial 9 (or 0). => (See note)
5. Dial telephone number.
Note:
Program #20 D Data Automatic Trunk Access Code for SLT Dial at Step 2 Dial at Step 4
0 0 97 0
1 9 07 9
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Nitsuko Telefonsystem Handbücher


















