Nobles SS2001E Programmierhandbuch

Model No.:

OSSS1701E

SS2001E

OSSS2001E

SS2001

SS2400

A TENNANT COMPANY

1--800-739--9359

616-786--2330

FAX: 1--800--678--4240

CUSTOMER SERVICE: 1--800-365-6625

NOBLES INDUSTRIES

12875 RANSOM STREET

HOLLAND MI 49424

173126

Rev. 02 (11-97)

Operator & Parts Manual

Speed Scrub

1701/2001/2400 Automatic Scrubber

ToOrderPartsCall1-888-702-5326-https://monsterfloorequipmentparts.com

OPERATION

2Speed Scrub 1701/2001/2400 (11--97)

This manual is furnished with each new Speed Scrub

model. It provides necessary operation and

maintenance instructions for both the electric and

battery models. Read this manual completely and

understand the machine before operating or

servicing.

This machine will provide excellent service. However,

the best results will be obtained at minimum costs if:

SThe machine is operated with reasonable care.

SThe machine is maintained regularly - per the

maintenance instructions provided.

SThe machine is maintained with manufacturer

supplied or equivalent parts.

MACHINE DATA

Please fill out at time of installation for future reference.

Model No.-

Install. Date -

Serial No.-

1997 NoblesRPrinted in U.S.A

Nobles and Speed Scrub are registered United States trademarks of

Tennant Company.

Specifications and parts are subject to change without notice.

TABLE OF CONTENTS

SAFETY PRECAUTIONS 3...................

MACHINE COMPONENTS 4..................

MACHINE INSTALLATION 5..................

MACHINE SET UP 6.........................

MACHINE OPERATION 8....................

DRAINING TANKS 10........................

BATTERY CHARGING 11....................

MAINTENANCE 12..........................

STORING MACHINE 13......................

TROUBLE SHOOTING 14....................

SPECIFICATIONS 15........................

PARTS LIST 16.............................

WIRE DIAGRAM 42..........................

ToOrderPartsCall1-888-702-5326-https://monsterfloorequipmentparts.com

OPERATION

Speed Scrub 1701/2001/2400 (11--97) 3

SAFETY PRECAUTIONS

This machine is suited to scrub floors in an indoor

environment and is not constructed for any other use.

Use only recommended pads and cleaning solutions.

All operators must read, understand and practice the

following safety precautions:

The following safety alert symbols are used throughout

this manual as indicated in their descriptions.

WARNING: To warn of hazards or unsafe

practices which could result in severe personal

injury or death.

CAUTION: to identify actions which must be

followed for safety operation of equipment.

1. DO NOT OPERATE, MAINTAIN OR SERVICE

MACHINE:

-- Unless trained and authorized.

-- Unless operator manual is read and

understood.

-- If it is not in proper operating condition.

2. WHEN OPERATING MACHINE:

-- Remove loose objects on floor. Loose

objects may become dangerous projectiles

if struck by revolving pad(s)/brush(es).

-- Keep hands and feet away from revolving

pad(s)/brush(es).

-- Keep machine moving to prevent damage

to finish or floor.

-- Do not run machine where flammable

liquids or gases are present.

-- Do not run on ramps or inclines unless

adequate personnel are present for

assistance.

For Electric Models:

-- Do not run over power supply cord.

-- Check cable and plug for damage.

-- Always work within cable length toavoid

cable stress and damage.

3. BEFORE LEAVING OR SERVICING MACHINE:

-- Make sure machine is turned “OFF”.

-- Disconnect batteries or unplug power

cord.

WARNING: Hazardous Voltage. Shock or

electrocution can result. Always unplug power

cord or disconnect batteries before servicing

machine.

WARNING: Batteries emit hydrogen gases,

explosion or fire can result. Keep sparks and open

flame away.

WARNING: Charge in a well ventilated area

and keep hood propped open when charging

batteries, explosion or fire can result.

WARNING: Battery acid can cause burns.

Wear protective gloves and shield eyes when

servicing batteries.

WARNING: Do not store outdoors and avoid

getting wet.

WARNING: The use of supplies other than

those recommended by manufacturer may cause

damage.

ToOrderPartsCall1-888-702-5326-https://monsterfloorequipmentparts.com

OPERATION

4Speed Scrub 1701/2001/2400 (11--97)

MACHINE COMPONENTS

12 11

24 23

17 19

1. Control Grips

Control Twist Grips (2400 Model)

2. Main/Drive ON/OFF Switch (2400 Model)

3. Vacuum ON/OFF Switch

4. Brush ON/OFF Switch

5. Battery Meter

6. Brush Circuit Breaker

7. Speed Thumb Lever (2400 Model)

8. Squeegee Lift Lever

9. Solution Flow Lever

10. Solution Flow Adjustment Knob

11. Adjustable Control Console Levers

12. Brush Lift Lever

13. Brush Lift Foot Lever

14. Recovery Tank Drain Hose

15. Solution Tank Drain Hose with Gallon Markers

16. Squeegee Assembly

17. Control Console

18. Recovery Tank

19. Recovery Tank Lid

20. Solution Fill Door

21. Safety Lights

22. Rear Drive Wheel

23. Scrub Head

24. Scrub Head Skirt

25. Wall Rollers

26. Front Casters

ToOrderPartsCall1-888-702-5326-https://monsterfloorequipmentparts.com

OPERATION

Speed Scrub 1701/2001/2400 (11--97) 5

MACHINE INSTALLATION

UNCRATING MACHINE

Carefully check carton for signs of damage. Report

damages at once to carrier. Check carton contents to

ensure all accessories are included. Squeegee is

packaged with machine. Batteries, battery charger and

pad driver(s) are packaged separately.

Battery installation must be accomplished after

removing machine from crate.

To uncrate your machine, remove straps and raise

brush head. To raise brush head, step down firmly on

the bottom brush lift foot pedal until pedal locks into

the raised position. Carefully lift or create a ramp using

crate boards to remove machine from pallet.

CAUTION: Do not roll machine off pallet,

damage may occur.

ATTACHING SQUEEGEE

1. Pull back on squeegee lift lever to raise squeegee

mount bracket.

2. Loosen two thumb knobs on squeegee and slide

squeegee into slot at rear of squeegee mount

bracket. Be certain that squeegee roller wheels

are toward the rear (Figure 1).

FIG. 1

3. Tighten thumb knobs securely.

INSTALLING BATTERIES

(For Battery Models Only)

WARNING: Batteries emit hydrogen gases,

explosion or fire can result. Keep sparks and open

flame away.

WARNING: Battery acid can cause burns.

Wear protective gloves and shield eyes when

servicing batteries.

Recommended Battery Specifications:

Two 12 volt deep cycle 130 amp hour batteries. Part

Number #130869. Maximum battery dimensions are

7-1/8W (180 mm) x 13L (330 mm) x 10”H (254 mm).

WARNING: To prevent accidental starting, be

certain key is removed from machine.

1. Turn all switches to the “OFF” position.

2. Carefully hinge open recovery tank sideways to

access battery compartment. Remove loose

battery cable and PVC battery spacer from

compartment (Figure 2).

FIG. 2

3. Carefully install batteries into compartment and

arrange battery posts as shown (Figure 3).

FIG. 3

ToOrderPartsCall1-888-702-5326-https://monsterfloorequipmentparts.com

OPERATION

6Speed Scrub 1701/2001/2400 (11--97)

WARNING: Do not drop batteries into

compartment! Battery and machine housing

damage may result. This damage is not covered

by warranty.

4. To secure batteries, place white PVC tube spacer

‘‘A” behind batteries in compartment as shown.

5. Connect cables to battery posts in numerical order

as labeled (RED TO POSITIVE & BLACK TO

NEGATIVE) (Figure 3.).

6. Double check cable connections before closing up

battery compartment.

MACHINE SET UP

PRE--OPERATION CHECKS

1. Sweep the floor to remove particles and other

debris.

2. Check battery meter charge level to ensure

batteries are fully charged if applicable. (See

BATTERY CHARGING)

3. Check that a pad(s) or brush(es) are installed.

4. Check that squeegee is installed.

INSTALLING BRUSH OR PAD DRIVER

FOR SAFETY: To prevent accidental starting, pull

out circuit breaker button before installing brush

or pad driver. Circuit breaker button is located at

rear of control housing.

1. Lower brush head, step down firmly on top pedal

and push pedal forward (Figure 4).

FIG. 4

2. Position squeegee swivel mechanism so it’s

centered behind machine.

3. Tilt machine back on squeegee to access motor

hub for pad driver/brush installation.

WARNING: Do not leave machine tilted back

for an extended time. Battery acid may run out the

top of batteries. Battery acid can cause severe

burns on contact with skin. Also, squeegee blades

may damage if left tilted back.

4. Select recommended pad or brush that best

meets your cleaning needs.

IMPORTANT: Consult your authorized distributor

to assist you in choosing the correct pad or brush

for your specific cleaning need.

5. (For Pad Installation) Attach pad to pad driver.

Attach pad before installing pad driver to motor

hub: Remove plastic centerlock from pad driver.

Position pad centered on pad driver and replace

centerlock securely (Figure 5).

FIG. 5

6. Attach brush or pad driver to motor hub. Align 3

mounting studs with slots in motor hub. Give the

driver a quick turn toward the spring clip on the

motor hub. Be certain pad driver is securely

fastened and spring clip locks into one of the studs

on the driver before operating machine (Figure 6).

FIG. 6

ToOrderPartsCall1-888-702-5326-https://monsterfloorequipmentparts.com

OPERATION

Speed Scrub 1701/2001/2400 (11--97) 7

7. Raise brush head. To raise brush head, step

down firmly on the bottom brush lift foot pedal until

brush locks into the raised position (Figure 7).

FIG. 7

FILLING SOLUTION TANK

1. Push machine to fill station. Raise squeegee and

brush when transporting.

2. Shut off solution flow, pull back completely on

solution flow lever (Figure 8).

FIG. 8

3. Open solution fill door at front of machine and fill

solution tank with up to 10 gallons (37.8 liters) of

water (140_F, 60_C maximum temperature). Clear

tub at rear of machine has 5 and 10 gallon

markers to indicate amount of water poured into

tank (Figure 9).

FIG. 9

NOTE: If filling with a bucket be certain that bucket is

clean. This will prevent the chance of clogging the

solution lines.

4. Add cleaning chemicals to the proper dilution ratio

according to the bottles instructions.

CAUTION: Use only recommended cleaning

chemicals, DO NOT use substitutes. Consult

authorized distributor to assist you with the

recommended cleaning chemicals.

WARNING: Use only nonflammable

commercial cleaning chemicals.

PLUGGING POWER CORD INTO A GROUNDED

WALL OUTLET (Electric Models Only)

Connect 75” extension cord to machine pigtail and

plug cord into a grounded outlet (Figure 10).

Grounded

Grounding

Edge/hole

Grounded

3HoleOutlet

Ground Pin

(

120V

)

(

230V

)

Outlet

FIG. 10

WARNING: To avoid serious personal injury,

plug power cord into grounded outlets only. Do

not use an adapter or remove ground pin on plug.

ToOrderPartsCall1-888-702-5326-https://monsterfloorequipmentparts.com

OPERATION

8Speed Scrub 1701/2001/2400 (11--97)

MACHINE OPERATION

1. Read and understand SAFETY PRECAUTIONS

before operating machine.

2. Adjust control grips to a comfortable operating

height (three settings). Squeeze together two

levers under console to raise or lower control grips

(Figure 11).

FIG. 11

3. Lower squeegee by releasing squeegee lift lever

from the lock position (Figure 12).

FIG. 12

4. Lower brush head, step down firmly on top brush

lift foot pedal and push pedal forward to release

(Figure 13).

FIG. 13

5. Turn vacuum switch to the ‘‘ON” position.

NOTE: For models with automatic drive, the vacuum

and brush switches will not run until the drive/main

switch is activated.

6. Push solution flow lever slightly forward to activate

solution flow. The further the lever is pushed

forward the more solution will flow. Push

completely forward for maximum flow. Solution will

immediately begin to flow once lever is activated.

(Figure 14).

FIG. 14

To increase or decrease the maximum solution

flow turn solution flow adjustment knob. Turn knob

down to increase solution flow or turn up to

decrease (Figure 15).

FIG. 15

ToOrderPartsCall1-888-702-5326-https://monsterfloorequipmentparts.com

OPERATION

Speed Scrub 1701/2001/2400 (NIL) 9

7. Turn brush switch to the ‘‘ON” position.

For models with automatic drive: Turn drive/main

switch to the “ON” position.

WARNING: To prevent floor finish damage,

DO NOT leave machine at stand still once brush

begins to spin.

8. Begin scrubbing by pushing machine forward.

For models with automatic drive: Slowly twist the

drive roll grips forward to begin scrubbing.

To increase drive speed, press and hold speed thumb

lever and twist roll grips further ahead. (Figure 16).

FIG. 16

WARNING: Always start machine in the

slower speed to prevent machine from leaping

forward.

9. View amount of solution flow on floor and adjust

solution control lever to desired solution flow.

WHILE OPERATING MACHINE

WARNING: Keep hands and feet clear of

revolving pad or brush.

1. Periodically check for foam buildup in recovery

tank (look through clear lid). If heavy foam buildup

begins to develop, pour a defoamer chemical into

the recovery tank.

WARNING: Do not allow foam or water to

enter the vacuum standpipe, vacuum motor

damage will result. Ball float shut--off will not keep

foam out of standpipe. Vacuum damage due to

foam or water is not covered by warranty.

2. If more scrubbing pressure is needed for small

heavily soiled areas, simply pull brush lift lever

upward (Figure 17).

FIG. 17

3. If squeegee leaves streaks, raise squeegee and

wipe both blades with a cloth.

4. Before stopping or turning machine around, pull

back on solution control lever to shut off solution

flow.

5. If you have to stop for more than three seconds,

shut off brush switch.

6. View clear tube gallon marker for remaining

cleaning solution left in solution tank.

7. Periodically check battery meter’s discharge level.

When needle drops to the red zone, recharge

batteries.

WARNING: Do not continue to run machine

when battery meter needle is in the red zone,

battery damage will result.

8. When the solution tank runs dry, turn off brush

switch, shut off solution control lever and continue

to vacuum until all dirty water is consumed into the

recovery tank. Raise the squeegee and brush

head and drain recovery tank (See DRAINING

TANKS).

PAD MOTOR CIRCUIT BREAKER

Machine is equipped with a circuit breaker to protect

pad motor from damage. If the pad motor circuit

breaker trips, it can not be reset immediately.

Determine reason why breaker tripped, allow motor to

cool and then reset. Circuit breaker will trip due to

excessive overload on pad. Clean or change pad if

breaker should trip. Pad motor circuit breaker button is

located at rear control console.

ToOrderPartsCall1-888-702-5326-https://monsterfloorequipmentparts.com

OPERATION

10 Speed Scrub 1701/2001/2400 (11--97)

DRAINING TANKS

1. Turn all switches to the “OFF” position. Unplug

power cord for electric models.

2. Raise squeegee and brush head and transport

machine to nearest floor drain.

NOTE: If using bucket to drain machine, do not use

same bucket for filling solution tank.

DRAINING RECOVERY TANK

Recovery tank must be emptied every time before

refilling solution tank. To drain recovery tank perform

the following steps:

WARNING: If recovery tank is not emptied

between fill ups, foam or water will enter the

vacuum standpipe and damage vacuum motor.

Float shut--off will not keep foam out of standpipe.

Vacuum damage due to foam or water is not

covered by warranty.

1. Remove drain hose from holder, position hose

over floor drain and twist off drain hose plug. To

completely drain recovery tank, hinge open tank

sideways and flip up tank support stand to rest

tank on (Figure 18).

FIG. 18

2. Rinse recovery tank after each use. This will

prevent a foul odor. Unscrew clear lid on recovery

tank. Use a hose to rise out the recovery tank. Be

careful not to spray water into float shut-off.

3. Replace drain hose plug tightly when tank is

empty.

DRAINING SOLUTION TANK

To drain leftover cleaning solution from solution tank

follow the steps below:

1. Pull clear gallon marker hose off hose barb at rear

of machine and drain solution into floor drain or

bucket (Figure 19).

FIG. 19

2. Flush solution tank with clean water after each

use. This will prevent clogging due to chemical

buildup. Let clean water drain out through clear

hose.

3. Push solution flow lever forward to rinse out

solution flow system.

4. Reconnect clear hose to hose barb. Be certain

hose is completely pushed on hose barb.

ToOrderPartsCall1-888-702-5326-https://monsterfloorequipmentparts.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nobles Bodenreinigungsmaschine Handbücher

Nobles

Nobles EZ Rider HP Bedienungsanleitung

Nobles

Nobles Explorert 1500H Produkthandbuch

Nobles

Nobles EZ Rider HP Bedienungsanleitung

Nobles

Nobles Marksman 412 Produkthandbuch

Nobles

Nobles Speed Scrub 2601 Produkthandbuch

Nobles

Nobles FALCON ULTRA B Produkthandbuch

Nobles

Nobles Speed Scrub 2401 Produkthandbuch

Nobles

Nobles speedshine 1200 Produkthandbuch

Nobles

Nobles 1500 Bedienungsanleitung

Nobles

Nobles Trooper 1000 Bedienungsanleitung

Nobles

Nobles Speed EX Bedienungsanleitung

Nobles

Nobles SPEED SCRUB Bedienungsanleitung

Nobles

Nobles Speedshine 1700DS Bedienungsanleitung

Nobles

Nobles Speed Scrub 2001 Produkthandbuch

Nobles

Nobles SPEED SCRUB Bedienungsanleitung

Nobles

Nobles 27 Bedienungsanleitung

Nobles

Nobles SPEED SCRUB 1033583 Bedienungsanleitung

Nobles

Nobles Speed Scrub 300 ec H2O NanoClean Bedienungs- und Montageanleitung

Nobles

Nobles 1016 Bedienungsanleitung

Nobles

Nobles Ultrashine 1000150 Produkthandbuch

Nobles

Nobles Scout 28 Bedienungsanleitung

Nobles

Nobles Marksmant 412 Produkthandbuch

Nobles

Nobles Trooper 1000 608811 Produkthandbuch

Nobles

Nobles Typhoon 1610P Pumpout Produkthandbuch

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch

BETCO

BETCO PB24 Bedienungsanleitung