Nordson Corona Cup Gun Ki Bedienungsanleitung

Instruction Sheet

E1997 Nordson Corporation

Issued 2/97 Manual 31-34

P/N 107 169A

Corona Cup Gun Kit

The Corona Cup Gun Kit was designed to easily attach onto your corona

gun without dismantling the gun. The cup gun kit is perfect for testing a

new powder, color, or for coating a small object when a full hopper is

unnecessary.

Follow these steps to install the Corona Cup Gun Kit.

See Figure 1.

1.Remove the lid (8) from the funnel (9). Inside the funnel you will find

a plastic screw (3) a wing nut (4) and two 1/4inch tube fittings.

NOTE: The two 1/4inch tube fittings are optional and should be used

if you have an older control unit with 1/4inch tube fittings and 1/4inch

OD tubing for atomizing and flow air. Replace the installed 6 mm

metric tube fittings with the 1/4inch tube fittings.

2.Remove the hose adapter (1) from your gun .

NOTE: A new hose adapter is included with the cup gun kit and

should be used in step 10.

3.Remove the nozzle (16) and the defector (17) from the gun.

4.Loosen the set screw (14) in the inlet body (15) and remove the inlet

body from the gun.

5.Rotate the inlet body 180 degrees so the powder inlet is facing

upward. Place the inlet body back onto the gun.

6.Secure the inlet body with the set screw (14).

7.Make sure the wear sleeve is in position and place the nozzle (16)

and deflector (17) back onto the gun.

8.Place the pump body (10) onto the hanger (13) so that the hole in the

pump body lines up with the hole in the hanger.

9.Secure the pump body with the screw (3) and the wing nut (4). Do

not overtighten the wing nut.

1. Introduction

2. Installation

Corona Cup Gun Kit

E1997 Nordson Corporation

107 169A

Issued 2/97

Manual 31-34

10. Insert the new hose adapter (1), attached to the short piece of powder

tubing into the gun inlet body (15).

11. Insert the atomizing air line into the lower air fitting (12) on the pump

body.

12. Insert the flow air line into the upper air fitting (12) connected to the

venturi nozzle in the pump.

13. Remove the cap from the bottom of the funnel (9) and push the funnel

into the hole in the top of the pump body with a slight twisting motion

until the funnel is snug.

Use the following steps to operate the corona cup gun kit.

1. Fill the cup gun funnel with powder coating.

2. Turn the control unit on and adjust the atomizing pressure to

1.7 bar (25 psi).

3. With the flow rate air pressure at zero, trigger the gun and slowly

increase the pressure until you reach the desired powder flow.

NOTE: Pressure settings will vary depending upon the powder type and

spraying conditions.

CAUTION: During cleaning with compressed air, steps should

be taken to prevent powder from being blown back into the

control gauges and regulators.

NOTE: Turn the electrostatics off and set the flow air and atomizing air

pressures at 3.4 bar (50 psi) before triggering the gun to clean. This will

prevent powder from migrating back into the controls.

Use an air gun to clean out the cup gun after use.

2. Installation

(contd.)

3. Operation

4. Cleaning

Corona Cup Gun Kit

E1997 Nordson Corporation

Issued 2/97 Manual 31-34

See Figure 1.

Use this list to order parts for the Corona Cup Gun Kit.

Item Part Description Quantity Note

ÁÁÁÁÁÁ

—

ÁÁÁÁÁ

183 468

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Kit, cup gun, corona

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁ

ÁÁÁÁÁ

135 896

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SAdapter, hose, low-flow, w/O-ring

ÁÁÁÁÁÁ

ÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

940 163

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SSO-ring, 0.625 x 0.75 x 0.063

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

900 649

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

STubing, powder, 9.5 mm (0.37 in.), blue

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

183 470

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SScrew, hex, nylon, M8 x 35

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

183 471

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SNut, wing, nylon, M8

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁ

ÁÁÁÁÁ

183 463

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SThroat, venturi, w/O-rings

ÁÁÁÁÁÁ

ÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

940 142

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SSO-ring, slcne, 0.50 x 0.625 x 0.063

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

940 126

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SO-ring, slcne, 0.375 x 0.50 x 0.063

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

183 453

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SLid, funnel cup gun

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

183 451

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SFunnel, molded, cup gun

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

183 452

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SBody, pump, cup gun

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁ

ÁÁÁÁÁ

183 462

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SNozzle, venturi, cup gun

ÁÁÁÁÁÁ

ÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

183 456

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SFitting, swv, el, 6 mm TBG x 1/8BPST

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

971 675

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SFitting, swvl, ELB, 1/4TB x 1/8NPT

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

900 784

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SCap/Plug, tapered, 0.485 OD

ÁÁÁÁÁÁ

ÁÁÁÁÁ

ÁÁÁÁÁÁ

ÁÁÁÁÁ

183 464

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SKit, funnel, w/lid and cap

ÁÁÁÁÁÁ

ÁÁÁÁÁ

AR: As Required

NS: Not Shown

5. Parts

Corona Cup Gun Kit

E1997 Nordson Corporation

107 169A

Issued 2/97

Manual 31-34

3134002A

2345

610 7

151617

13 14

15 16 17

Fig. 1 Corona Cup Gun Kit

Nordson and the Nordson logo are registered trademarks of Nordson Corporation.

5. Parts

(contd.)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nordson Spritzpistole Handbücher

Nordson

Nordson SDS 40-CC Meter Bedienungsanleitung

Nordson

Nordson ColorMax3 Bedienungsanleitung

Nordson

Nordson Prodigy Robot Gun Referenzhandbuch

Nordson

Nordson Tribomatic II Referenzhandbuch

Nordson

Nordson Universal Series Referenzhandbuch

Nordson

Nordson Kinetix 334593-04 Referenzhandbuch

Nordson

Nordson A7A Referenzhandbuch

Nordson

Nordson FP-200 Bedienungsanleitung

Nordson

Nordson Encore PE Bedienungsanleitung

Nordson

Nordson WM-1 Referenzhandbuch

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Nordson

Nordson ColorMax Bedienungsanleitung

Nordson

Nordson Trilogy GP Referenzhandbuch

Nordson

Nordson Compact Manual Iso-Flo Voltage-Block Bedienungsanleitung

Nordson

Nordson ColorMax 2 Referenzhandbuch

Nordson

Nordson PRODIGY Referenzhandbuch

Nordson

Nordson Encore Bedienungsanleitung

Nordson

Nordson ColorMax 2 Bedienungsanleitung

Nordson

Nordson Trilogy Bedienungsanleitung

Nordson

Nordson Vantage Referenzhandbuch

Nordson

Nordson Mastic Gun Referenzhandbuch

Nordson

Nordson Encore XT Referenzhandbuch

Nordson

Nordson Tribomatic Magnum Bedienungsanleitung

Nordson

Nordson Encore PE Bedienungsanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

Graco

Graco EM 390 Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung

Graco

Graco HydroShield WMBH00 Stücklistenhandbuch

WAGNER

WAGNER W 125 Bedienungsanleitung

My Clean Buddy

My Clean Buddy PW018 Bedienungsanleitung