Noritz MR-2 Bedienungsanleitung

1



MR‐IM‐2

Rev.3/21

InstallationGuide

CommercialMulti‐RackSystem

Model:MR‐2

InstallationTime:5‐10Minutes

WARNING

Inordertoproperlyinstallthisaccessory,please

readtheInstallationManualcarefullybefore

proceeding.Failuretodosocouldresultina

seriousinjury.

RequestforInstallers:

Anycasesofdamageormalfunctionduetoimproperinstallationwillbethe

responsibilityoftheinstallerregardlessofwarrantycoverage.

PleaserefertotheInstallationManualincludedwiththewaterheaterforadditional

informationtocompletetheinstallation.

Oncetheinstallationiscompleted,confirmallproceduresbasedonthisInstallation

Guide.

2

Introduction

IncludedParts

ThefollowingpartsaresuppliedintheCommercial

Multi‐RackSystem.Checkforanymissingitems

beforestartingtheinstallation.



ThismanualcoverstheinstallationoftheNoritzCommercialMulti‐RackSystem(#MR‐2)forcommercial

tanklesswaterheatermodels.ThemodeltypecanbeverifiedfromtheRatingPlatelocatedonthewater

heaterinordertocheckforcompatibility(seebelow).Pleasereadthefollowinginstructionscompletely

beforestartingtheinstallation.



CompatibleNoritzCommercialModels: 

NC199Series*

NCC199Series

NC250Series

NC380‐SV‐ASME



Parts/ToolsRequired:

PhilipsScrewdriver

SocketWrench

Level

Pencil/Marker

*NC199seriesmodelswillrequireadditionalpre‐drilled

holesontheRackTopand/ortheAdjustableMounting

Plateforadirectfittothemountingbracketsonthe

waterheater.SeeNoteonPage4.

3

InstallationProcedure Donotattempttoovertightenanyofthe

boltsasthismaydamagethethreadsand

preventtheboltfromturning



1) DeterminethebestareatoinstalltheCommercialMulti‐RackSystemwhereallthesafetyand

clearancerequirementstothewaterheaterandventingaremet.



2) Removeallitemsfromthepackagingandensurethatallpartsandaccessoriesareincludedinthekit.



3) SettheRackBaseatthedesiredinstallationlocationandlayitflatontheground.



4) TaketheRackTopAssemblyandholditnearthecenterofthebaseasshowninFigure1.Usethe

includedM12boltsettoattachtheRackToptothebase.Afterthatiscompleted,takebothleftand

rightReinforcementPlatesanduseM12boltstoattachthemtotheholesprovidedontheRackTop

andBaseforaddedstability.



 



<Figure1>InstallationofCommercialMulti‐RackSystem

4

5) UsetheAdjustableMountingPlatefromtheRackTopAssemblyandattachittotheracksystemin

eitherPosition2or3usingtheprovidedholesontheRackTopasshowninFigure2below.Position

1willnotbeused.Refertothechartbelowforcorrespondingpositionstothelistedcompatible

models.





Position2Position3

NC199,NCC199,NC250Series NC380, NCC300Series



<Figure2>ProperPositionoftheAdjustableMountingPlate



6) CAUTION!Confirmthattheracksystemremainsflatandsecuretothegroundbeforeanyunitsare

mounted.Topreventtherackfromfallingoverandpossiblycausinginjury,usefield‐supplied

anchorboltstosecuretheRackBasetothefloor.



7) Oncetherackhasbeenproperlyinstalledandsecured,carefullyholdtheNoritzwaterheaterin

placeandusethefivetappingscrewstomounttheunittotherack(Figure3).Anumberof

mountingholesareprovidedtofitthetopandbottommountingbracketsonthewaterheater.



FORNC199SERIESMODELS:Someadditionalmountingholeswillbeneededtosecurelymountthe

NC199seriesmodelstotherack.PlacetheunitagainsttheRackTopandlineupallthemounting

pointstotheAdjustableMountingBracket.Usealeveltomakesurethatthewaterheateris

mounteduprightanduseapencilormarkertomarktheareaswherethenewholeswillbeneeded.

Usetheprovidedtappingscrewstoattachtheunittotherackandcompletetheinstallation.

5



<Figure3>MountingtheWaterHeatertotheRackSystem



8) Attachthewaterandgasconnectionstothewaterheater(s)accordingtotheInstallationManual

providedwiththeunits.Wheninstallingmultiplewaterheatersontherack,makesuretofollowall

clearancerequirementsfromtheunitasstatedontheRatingPlate.

Inhaltsverzeichnis

Andere Noritz Rack & Stand Handbücher

Noritz

Noritz CR60 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung