Norix PRD-RR06K Bedienungsanleitung

3/8" Drill Bit (1)

029-947

Threaded Insert (12)

029-943

Restraint Ring, Sq. Bottom (6)

029-942

Restraint Ring Pin,

Push Lock 002-017 (6)

Key 029-162 (4)

Drill Guide, Restraint (1)

011-064

Restraint Ring Bracket (6)

011-057

Screw, 1/4-20 X 3/4" L,

BH (12)

021-070

Screw, Sheet Metal,

#12-11 X 1.5 L,

Ext. Hex, Slotted (12)

021-203

Attenda, Restraint Ring Spacer

For Push-Lock Pin, Stainless Steel,

Removable

002-019 (6)

3/4" Drill Bit (1)

029-946

Patents Pending

Restraint hardware:

Please familiarize yourself with the Restraint Kit components as shown below.

If any components are missing, contact Norix Customer Care before proceeding.

Important Note: For a successful installation, careful and accurate

layout of the restraint brackets is a must. Read through the

instructions first and familiarize yourself with all of the steps. If you

have any questions, please call Norix Customer Care before

proceeding. Norix is not responsible for damage to components

due to improper installation.

Tools Needed

Low RPM Variable Speed Drill

6mm Hex Driver

Pin-in-Torx® Driver T-27

5/16" Hex Driver

www.norix.com ● TEL 800 234-4900

Assembly Notes:

Norix is not responsible for any damage due to improper installation. If your shipment does not match the parts list, please contact Norix Customer Service at 800-234-4900.

Norix reserves the right to modify design specifications at any time without an obligation to owners of previously sold products.

___________________________________________________________________________________________________________________________________________________________________________________________________

Prodigy Restraint Ring Kit

Assembly Instructions

Model Number

PRD-RR06K

Page 1 of 5

Rev. F - 1/12/21

091-991

Restraint location

(6) per side

Drill Guide

Threaded Insert

Restraint location

(6) per side

Drill Guide

Hold flat against

outside bed

surface

Threaded Insert

Tighten until flange

is flush with bed

surface

1. Determine desired locations for Restraint Rings. Any

of the six locations on each side can be used.

Drill Holes for Brackets

To drill the holes and install brackets, it is easiest if the

Bed is on its side. Place padding on the floor to

protect from scratches.

Wear protective gloves

when drilling holes, in case of

an accidental slip.

Place the Drill Guide on the Bed in the desired

location. The Drill Guide may be held by hand, or

clamped in place with a padded C-clamp if

necessary.

Hold the Drill Guide flat against the outside

surface as shown

It is important to drill the holes accurately in the

correct positions.

3. Using the provided 3/4" brad-point drill bit, drill

through the Bed. Drill carefully, and don't force the

bit. The Guide will help drill a hole that is

perpendicular

to the outer face of the Bed. High

speed on the drill is recommended.

If you must retract the drill bit to clear the chips,

ensure that you do not move the drill guide before

resuming so that you achieve a cleanly drilled hole.

Repeat drilling a hole in the other locations where

brackets will be installed.

Install first threaded insert

Using a 6mm Hex Driver, install a threaded insert in the hole

adjacent to each bracket location. Tighten until the flange

is flush with the bed surface.

Do not overtighten.

Page 2 of 5

Rev. F - 1/12/21

091-991

Drill direction

Bottom Plane

Drill approximately

1" deep

YAA

Install Restraint

Ring & Pin

Drill approximately 1" deep

Install 2nd threaded insert

Place a Restraint Bracket in its final position and

loosely

install a 1/4-20 screw into the insert to hold the Bracket in

place temporarily.

Use the supplied 3/8" drill bit to drill a hole for the 2nd

Insert.

Using the Bracket as a guide, carefully drill through the

hole on the same face as the first screw, as shown in

the illustration. Drill approximately 1" deep.

Remove the Restraint Ring, Pin, & Bracket.

Using a 6mm Hex Driver, install a threaded insert into the

drilled hole. Tighten until the flange is flush with the bed

surface.

Do not overtighten.

Tip: If the hole has become out of round or a loose fit with

the insert, wrap the insert with tape to provide a snug fit.

Repeat for other Bracket locations.

Install a Restraint Ring and Restraint Ring Pin into the

Bracket.

There may be a small amount of movement in the

Bracket, so

push it toward the outside

of the bed for

best results.

Page 3 of 5

Rev. F - 1/12/21

091-991

Restraint Ring Bracket

Screw, 1/4-20 X 3/4" L

Ensure that end of bracket tube is

flush or slightly protruding with

outside surface of bed.

1/4-20 Screws

#12 Sheet Metal

Screws

Install Brackets

Insert the Bracket into the drilled hole in the

Bed.

Install the Restraint Ring & Pin into the Bracket.

If there is play in the bracket, push it toward

the outside of the bed while installing the (2)

1/4-20 Screws.

Tighten the screws.

Do not overtighten.

Install (2) #12 Sheet Metal Screws on the back

side of the Bracket. No pre-drilling is required.

Tighten the screws until snug.

Do not overtighten.

Repeat for all locations.

Test the fit and function of all Pins with and without

Restraint Rings in all locations before anchoring the bed.

Adjust Brackets if necessary to ensure that Pins lock in all

positions.

Page 4 of 5

Rev. F - 1/12/21

091-991

Restraint Ring Bracket

Screw, 1/4-20 X 3/4" L

Ensure that end of bracket tube is

flush or slightly protruding with

outside surface of bed.

Restraint Ring Pin

Restraint Ring Key

Restraint Ring

unlock

, insert and

turn the key in either

direction.

Slot

Restraint Ring Pin

Push Button to lock

Restraint Ring Removed.

Always use Spacer when Restraint

Ring is not present.

Push Button

to lock.

Restraint Ring

and Pin Installed

Spacer

Restraint Ring Pin

Receptacle

(Bracket)

Locking

After the Restraint Ring Pin and Ring are assembled to

the Bed, push the Button on the Pin to lock.

Unlocking and removal

Hold onto the Pin while turning the key to prevent the Pin

from turning.

To unlock

, insert the key with the tooth on the key

aligned with the slot on the Pin and turn slightly in either

direction.

Pull the Ring and Pin to remove from the Bed.

Once the Ring is removed, the Pin can be put back to fill

the receptacle in the bed. Use the provided Spacer

with the Restraint Pin.

Removable Restraint Ring Function

With No Restraint Ring

Page 5 of 5

Rev. F - 1/12/21

091-991

Andere norix Inneneinrichtung Handbücher

norix

norix TNT1X1X Bedienungsanleitung

norix

norix Prodigy PRD700 Bedienungsanleitung

norix

norix TNT0802-BX1 Bedienungsanleitung

norix

norix ATN101-XXX.3 Bedienungsanleitung

norix

norix Titan TNT1620-0L T Series Bedienungsanleitung

norix

norix C221 Series Bedienungsanleitung

norix

norix PRD100 Bedienungsanleitung

norix

norix Protege II Single PROT100 Series Bedienungsanleitung

norix

norix Oasis Classroom Table Bedienungsanleitung

norix

norix Titan TNT1991 Bedienungsanleitung

norix

norix TNT1853-0000XXT Bedienungsanleitung

norix

norix PRD240 Bedienungsanleitung

norix

norix TNT0500-00XT Bedienungsanleitung

norix

norix B510-2127 Bedienungsanleitung

norix

norix C221-111 Series Bedienungsanleitung

norix

norix TNT0300-FL002T Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung

norix PRD-RR06K Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken