Notifier AM-6000 Bedienungsanleitung
Installation Manual
Document : M-180.2-AM6000-ENG
Issue :10/1999 Rev. :B.2
AM-6000
Analog Fire Alarm
Control Panel
NOTIFIER ITALIA
A Division of Pittway Corporation
INDEX
»This new revision, B.2, includes an Appendix on page 27 about “AM-6000 Power Supply”.
AM-6000 Exploded View1
Cabinet2
Mounting the system boards to the “ICA-6” chassis3
Front Panel indication & keypad4
“BE-600A” Main Board layout5
Connector CNA on “BE-600 A” board 6
Connector CN0 “BE-600 A” board 6
Serial Printer connections 6
Connector CN1 on “BE-600 A” board 7
“BPS-600” board for 230 V Mains wiring8
Wiring the “BE-600 A” Main Board external devices9
Detector and Module wiring - Typical LOOP line (style 6)10
“LIB-600” Expansion Board layout11
Connector CN1 on “LIB-600” Expansion Board12
“AVPS-6” Aux. Power Supply Board 13
“DIA-6”: front panel display and keypad interface layout14
Analog identification system components 15
Class “A” wiring circuit and line isolators16
Notes about loop wiring17
SLC LOOP shield wiring 21
Connector CN2 on “SIB-600” optional board 22
The 220 VAC Power Supply Line 23
Main Power Supply current draw calculation24
Alarm condition current load25
Battery capacity calculation26
APPENDIX: AM-6000 POWER SUPPLY (Refer to note 1)
Note 1: Added in this new revision
Index.VPInstallation Manual
Doc. M-180.2-AM6000-ENGRev. B.2NOTIFIER ITALIA
AM-6000 EXPLODED VIEW
Page 1 Installation Manual AM-6000-60002.VP
NOTIFIER ITALIA Rev. B.1 Doc. M-180.2-AM6000-ENG
ATTENZIONE
230 V
ATTENZIONE
230 V
126
1
1
12
12
126
126
126
AVPS 6 Board for 3 A Aux. Power Supply
complete of transformer
BE 600 A
Main Board
including support
and transformer
CVCV-0117 Power Supply Cable
DR 6 Dust Preventer Door
CVCV-0125 : 3-board Flat Cable
ICA 6 CHASSIS
LIB 600 Expansion Board (Board 1)
LIB 600 Expansion Board (Board 2)
LIB 600 Expansion Board (Board 3)
DP 6 Dress Panel (3 U)
CVCV-0123 Flat Cable
CAB 6 Wall- mounting Cabinet
SIB 600 Serial Board
SK8 R, SK16 R
Relay Board
BPS600 Board for 230 V Mains Wiring
CVCV-0124 Flat Cable
DIA 6 Front Board
Operator Keypad
•
DIA 6M-I (Italian)
•
DIA 6M-E (English)
•
DIA 6M-S (Spanish)
CABINET
AM-6000-60001.VP Installation Manual Page 2
Doc. M-180.2-AM6000-ENG Rev. B.1 NOTIFIER ITALIA
65 mm 405 mm
535 mm
65 mm
75 mm
55 mm
46.5 mm
30.5 mm
35 mm
30
mm
30
mm
35
mm
35
mm
75
mm
75
mm
35
mm
35
mm
35
mm
35
mm
35
mm
35
mm
105
mm
105
mm
45
mm
45
mm
365 mm
440 mm
200 mm
30 mm
.
.
4 Mounting Holes
> screw max. Dia. : 6.0 mm.
4 openable holes
28.0 mm. dia.
1 openable hole - 28.0 mm. dia.
> bottom side
Openable Holes 28.0 mm dia.
> 2 bottom side
> 2 top side
Dust preventer door
MOUNTING THE SYSTEM BOARDS to the “ICA-6" CHASSIS
INSTALLING THE ICA-6 CHASSIS
1
- Screw the two spacers4x45MF(
A
) to the plate.
2
- Secure the metal plaquette (
B
) with the two screws4x8TC(
C
).
3
- Insert the chassis on the proper hinges (
D
). Then push the chassis inward toward the bottom of the cabinet.
A click will confirm the correct seat of the chassis (
E
).
Page 3 Installation Manual AM-6000-60001.VP
NOTIFIER ITALIA Rev. B.1 Doc. M-180.2-AM6000-ENG
FRONT PANEL INDICATION & KEYPAD
DIMENSIONS
•
Front panel including the hinge = 482 x 266 mm (19" - 6 units).
•
Mounting holes wheel-base : Horizontal = 465 mm. - Vertical = 190 mm.
AM-6000-60001.VP Installation Manual Page 4
Doc. M-180.2-AM6000-ENG Rev. B.1 NOTIFIER ITALIA
NOTIFIER
Division of Pittway Corporation
INTELLIGENT FIRE DETECTION SYSTEM
AM-6000
NEXT
KJIH
Z
O
NM
U
TS
)
R
SPACE
X
V W
G
Q
Y
LAMP
TEST
LAMP
TEST
4
7
5
8
0
6
9
ACK
READ
STATUS
READ
STATUS
MODIFY
STATUS
MODIFY
STATUS
PROGRAMMING
SPECIAL
FUNCTIONS
SPECIAL
FUNCTIONS
REPEAT
ED
C
B
A
F
P
L
(
SIGNALSILENCE
SYSTEM
RESET
SYSTEM
RESET
SYSTEM
TEST
SYSTEM
TEST
LISTLISTRESTORE
SILENCE
RESTORE
SILENCE
1
SILENCED
CONTROLS
SILENCED
CONTROLS
23
ALARM
DISABLED
ZONES/POINTS
DISABLED
ZONES/POINTS
GENERAL
TROUBLE
GENERAL
TROUBLE
SYSTEM
TROUBLE
SYSTEM
TROUBLE
PANELOK
“BE-600 A” MAIN BOARD LAYOUT
Page 5 Installation Manual AM-6000-60001.VP
NOTIFIER ITALIA Rev. B.1 Doc. M-180.2-AM6000-ENG
1 26
1
1
12
12
Led indicating trouble condition (Line 1-4)
CPU-Reset push-button
Led indicating alarm condition (Line 1-4) Connector for SIB 600
Serial Board interconnection
CRT/LCD serial communication
line Status LED
Product identification
Factory code number
Siren Fuse 3 A 15 (Monitored Line)
Jumper to Enable/Disable
Earth trouble Signal
Start-up from battery only.
(Execute a short circuit between the two PIN)
Connector for BPS 600 PSU board
interconnection
Earth: connect to SIB 600 serial Board
Earth: connect to LIB 600 expansion boards
Control Panel powered Led
Battery Low Trouble Led
Printer serial communication
line Status Led
Connector for AVPS 6 auxiliary
Power supply interconnection
Earth: connect to AVPS 6 auxil. power supply
Connector for DIA 6 front board interconnection
Connector for LIB 600
expansion board interconnection
Connector for future expansion
4 Status Leds concerning the detector line serial communication
Detection Lines (1-4)
Program Eprom
User Fuse 3 A 15 + 24 V
Positive to Earth
Negative to Earth
}
CONNECTOR CNA on “BE-600 A” BOARD
CONNECTOR CN0 on “BE-600 A” BOARD
NOTE:
(
*
) these two outputs CANNOT operate simultaneously. The operator must select the Type of Connection to
employ, from the Control Panel Main Programming Menu (refer to AM-6000 Programming Manual).
SERIAL PRINTER CONNECTIONS
AM-6000-60001.VP Installation Manual Page 6
Doc. M-180.2-AM6000-ENG Rev. B.1 NOTIFIER ITALIA
TERMIN. NR. DENOMINATION NOTE USE FOR : CABLE COLOUR/NR.
1
+ 24 V User
0,5
2
GND P
2A
3
+ 24 V User Resettable
0,5 ISOLATED BY MANUAL RESET
4
GND P
2A
5
Siren Supervis.Line+(Stand by)
3A
6
Siren Supervis.Line -(Stand by)
7
SIGNAL SILENCE
N.O. CONTACT
8
RESET
N.O. CONTACT
9
+ 24 V Auxiliary
3 A ONLY IF AVPS 6 IS INSTALLED
10
GND P
ONLY IF AVPS 6 IS INSTALLED
11
+ 24 V Aux. Resettable
3 A ONLY IF AVPS 6 IS INSTALLED
12
GND P
TERMIN. NR. DENOMINATION NOTE USE FOR : CABLE COLOUR/NR.
1
GROUND
2
RS 232 TX - PRN 2400 Baud
3
RS 232 RX - PRN PRINTER 7 BIT
Parity : EVEN
4
GND IS 1 BIT STOP
5
RS 232 TX
(
*
)
CRT-TERMINAL FOR EXTERNAL
6
RS 232 RX PROGRAMMING (CRT/PC TERM.)
7
GND IS
8
RS 485 LIN + (OUTWARD)
(
*
)
9
RS 485 LIN - (OUTWARD) LCD-6000 REPEATERS
10
GND IS
11
RS 485 LIN + (RETURN)
12
RS 485 LIN - (RETURN)
Twisted pair
Twisted pair EIA-232 Reference
EIA-232 Reference
Receive from printer
n.c.
4 (terminal)
2 (terminal)
3 (terminal)
TO PRINTER
SIGNAL DEFINITION BE-600 A BOARD CNO
Plug the DB-25 connector into the EIA-232 port of the printer
CONNECTOR CN1 on “BE-600 A” BOARD
»NOTE :
1) If a line is programmed as Style 6 (loop line), terminals A are the OUTWARDS and terminals B are the RETURN.
2) For each line connect the shield to appropriate SC terminal.
3) Alarm and Trouble Controls : free voltage contacts.
Use to drive loads in DC only.
Alarm is activated if a detector of line 1-4 is in ALARM condition.
Trouble is activated if a detector of line 1-4 is in TROUBLE condition.
Page 7 Installation Manual AM-6000-60001.VP
NOTIFIER ITALIA Rev. B.1 Doc. M-180.2-AM6000-ENG
TERMINAL
NUMBER DENOMINATION NOTE LINE ID. CABLE
COLOUR/NUMBER
1
A1 +
(1)
2
A1 -
3
B1 +
(1) DETECTOR LINE 1
4
B1 -
5
SC 1
(2)
6
A2 +
7
A2 -
8
B2 +
DETECTOR LINE 2
9
B2 -
10
SC 2
11
A3 +
12
A3 -
13
B3 +
DETECTOR LINE 3
14
B3 -
15
SC 3
16
A4 +
17
A4 -
18
B4 +
DETECTOR LINE 4
19
B4 -
20
SC 4
21
ALARM RL - N.O.
(3)
22
ALARM RL - COM
23
ALARM RL - N.C.
3A
24
TROUBLE RL - N.O.
30 VDC
25
TROUBLE RL - COM
26
TROUBLE RL - N.C.
“BPS-600" BOARD for 230 V MAINS WIRING
AM-6000-60001.VP Installation Manual Page 8
Doc. M-180.2-AM6000-ENG Rev. B.1 NOTIFIER ITALIA
ATTENZIONE
230 V
ATTENZIONE
230 V
LED indicating
Battery-charger operating
LED indicating Auxiliary
Power Supply operating
LED indicating
Control Panel Powered
Battery Fuse
6A
Connectors to Primary coil
(230 V Power)of
TAM6-P/TAM6-S transformers
Connector to Secondary coil of TAM6-S
transformer (auxiliary Power supply)
Connector to BE-600 A
Main Board
Jumper to connect the earth to
Panel negative Power
LED indicating main
Power Supply operating
Battery-Charger Fuse
3,15 A
Main Power Supply Fuse - 4A
Auxiliary Power Supply Fuse - 4 A
230 V Mains
Fuse 5 A
230 V Mains Input
Connector to Secondary coil of TAM6-S
transformer (Main Power supply)
= not connected
= negative connect. to the earth
Inhaltsverzeichnis
Andere Notifier Bedienfeld Handbücher
Notifier
Notifier Fire Alarm Control Panel Bedienungsanleitung
Notifier
Notifier AFP-400 Betriebsanleitung
Notifier
Notifier NFS2-640/E Bedienungsanleitung
Notifier
Notifier AFP-400 Bedienungsanleitung
Notifier
Notifier 4812 Bedienungsanleitung
Notifier
Notifier NFS2-640/E Bedienungsanleitung
Notifier
Notifier FireWarden-100-2 Bedienungsanleitung
Notifier
Notifier AFP-300 Betriebsanleitung
Notifier
Notifier NFS-640 Bedienungsanleitung
Notifier
Notifier MINIGAS Montageanleitung
Notifier
Notifier AM2020/AFP1010 Bedienungsanleitung
Notifier
Notifier AFP-3030 Bedienungsanleitung
Notifier
Notifier NFS-320 Bedienungsanleitung
Notifier
Notifier NFS-3030/E Bedienungsanleitung
Notifier
Notifier AFP-3030 Bedienungsanleitung
Notifier
Notifier CFP-600-E Bedienungsanleitung
Notifier
Notifier AM2020 Bedienungsanleitung
Notifier
Notifier AFP-300 Bedienungsanleitung
Notifier
Notifier AFP-3030 Bedienungsanleitung
Notifier
Notifier AFC-600 Bedienungsanleitung
