Novus NVIP-2D-6502/F Bedienungsanleitung

Quick sta rt gu i de

NVIP-2D-6502/F

NVIP-2D-6502/F Quick start guide version 1.0

THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed

for self installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other

devices during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN

PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE

PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING

THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.

DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 26 February 2014 on the harmonisation of the laws of the Member States

relating to electromagnetic compatibility (OJ L 96, 29.3.2014, p. 79–106, with changes)

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 4 July 2012 on waste electrical and electronic equipment (WEEE)

(OJ L 197, 24.7.2012, p. 38–71, with changes)

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances in

electrical and electronic equipment (OJ L 174, 1.7.2011, p. 88–110, with changes)

IMPORTANT SAFEGUARDS AND WARNINGS

Pictures in this publication showing camera views can be simulations. Actual camera

images may vary depending on the type, model, settings, observation area, or

environmental conditions.

NVIP-2D-6502/F Quick start guide version 1.0

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER

-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL

MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and

operating instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual

is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the

user’s manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools,

bath tubs, damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.)

is not recommended since it may lead to heat build-up and damaging the device itself as a

consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden.

Improperly mounted camera may cause a fatal accident or may be seriously damaged itself. The

camera must be mounted by qualified personnel with proper authorization, in accordance with this

user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with

those specified by the producer in the camera technical datasheet. Therefore, it is forbidden to

supply the camera from a power sources with unknown parameters, unstable or not meeting

producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions

described in the manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com/en website in order to access the newest full

manual

IMPORTANT SAFEGUARDS AND WARNINGS

NVIP-2D-6502/F Quick start guide version 1.0

TABLE OF CONTENTS

1. FOREWORD INFORMATION .....................................................................................5

1.1. General characteristics.........................................................................................5

1.2. Technical specification .......................................................................................6

1.3. Camera dimension ..............................................................................................7

1.4. Package contents..................................................................................................7

2. START-UP AND INITIAL CONFIGURATION .........................................................8

2.1. Description of connectors....................................................................................8

2.2. Description of camera components .....................................................................8

2.3. Zoom and focus adjustment.................................................................................9

2.4. Connecting ethernet cable ...................................................................................9

2.5. Connecting power supply to the camera...........................................................10

2.6. Camera mounting ..............................................................................................10

2.7. Starting the camera ............................................................................................11

2.8. Initial configuration via the web browser..........................................................12

2.9. Security recommendations for network architecture and configuration ...........13

3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................14

3.1. Recommended PC specification for web browser .............................................14

3.2. Connection with camera via web browser .........................................................14

4. USING AND CONFIGURING .....................................................................................16

4.1. The remote preview interface.............................................................................16

5. ELECTRICAL CONNECTIONS AND ACCESORIES...........................................17

5.1. Connecting alarm input/output...........................................................................17

5.2. Memory card installation....................................................................................18

5.3. Connecting audio to the camera .........................................................................18

6. RESTORING FACTORY DEFAULTS .....................................................................19

6.1. Restoring factory settings using the www panel ................................................19

6.2. Restoring factory settings using NMSiptool application ...................................19

6.3. Factory reset with button...................................................................................20

TABLE OF CONTENTS

NVIP-2D-6502/F Quick start guide version 1.0

1. FOREWORD INFORMATION

1.1. General Characteristics

• Sensor resolution: 2 megapixels

• Mechanical IR cut filter, IR operation capability

• Min. Illumination from 0 lx with IR LED on

• Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

• Digital Noise Reduction (DNR)

Lens type: varifocal, f=2.8 - 12 mm/F=1.4

• Built-in LED illuminator: 30 pcs LED

• Built-in webserver: camera configuration through the website

• Compression: H.264, H.265, H.264+, H.265+, H.264 Smart, H.265 Smart, MJPEG

• Max video processing resolution: 1920 x1080

• Multi streaming: compression, resolution, speed and quality defined individually for each video

stream

• ROI functions

• Motion detection

• Private Zones

• RTSP protocol support for video transmission

• Schedule

• Micro SD card up to 128 GB

• Audio input

• Audio output

• Bulid-in microphone

• Alarm input (NO/NC)

• Alarm Output

• Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server,

saving file on SD card, alarm output activation

• Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,

playback and remote IP devices administration

• Video Content Analysis (VCA):

Exception

Line Crossing

Region Entrance

Region Exiting

Target Counting

Intrusion

Face Detection

• Power supply: 12VDC, PoE (Power over Ethernet)

FOREWORD INFORMATION

NVIP-2D-6502/F Quick start guide version 1.0

1.2. Technical specification

FOREWORD INFORMATION

IMAGE

Image Sensor 2 MPX CMOS sensor 1/2.8” SONY STARVIS

Number of Eecve Pixels 1920 (H) x 1080 (V)

Min. Illuminaon 0.0038 lx/F1.4 - color mode,

0 lx (IR on) - B/W mode

Electronic Shuer auto/manual: 1/3 s ~ 1/10000 s

Digital Slow Shuer (DSS) up to 1/3 s

Wide Dynamic Range (WDR) yes (double scan sensor), 120dB

Digital Noise Reducon (DNR) 3D

Defog Funcon (F-DNR) yes

Highlight Compensaon (HLC) yes

Back Light Compensaon (BLC) yes

Reducon of image icker (Anicker) yes

LENS

Lens Type varifocal, f=2.8 ~ 12 mm/F1.4

DAY/NIGHT

Switching Type mechanical IR cut lter

Switching Mode auto, manual, me

Switching Level Adjustment yes

Switching Schedule yes

Visible Light Sensor yes

NETWORK

Stream Resoluon 1920 x 1080 (Full HD), 1280 x 720 (HD), 704 x 576, 480 x 240, 352 x 288

Frame Rate 30 fps for 1920 x 1080 (Full HD) and lower resoluons

Mulstreaming Mode 3 streams

Video/Audio Compression H.264, H.264+, H.264 Smart, H.265, H.265+, H.265 Smart, MJPEG/G.711

Number of Simultaneous Connecons max. 10

Bandwidth 60 Mb/s in total

Network Protocols Support HTTP, TCP/IP, IPv4/v6, UDP, HTTPS, FTP, DHCP, DDNS, NTP, RTSP, UPnP,

SNMP, QoS, IEEE 802.1X, PPPoE, SMTP

ONVIF Protocol Support Prole S

Camera Conguraon from Internet Explorer browser

languages: Polish, English, Russian, and others

Compable Soware NMS, NVR-6000 Viewer

Mobile applicaons SuperLive Plus (iPhone, Android)

OTHER FUNCTIONS

Privacy Zones 4

Moon Detecon yes

Region of interest (ROI) 8

Video Content Analysis (VCA)

tamper, line cross, zone entrance, zone exit, object counng, Scene

Change, Video Blurred, Video Color Cast, objects disnguishing, face

recognion

Image Processing 180˚ image rotaon, sharpening, mirror eect, corridor mode, lens

distoron correcon

Prealarm/Postalarm up to 6 s/up to 120 s

NVIP-2D-6502/F Quick start guide version 1.0

FOREWORD INFORMATION

1.3. Camera dimensions

1.4. Package contents

After you open the package make sure that the following elements are inside:

• IP camera

• Accessories bag

• Quick start guide

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

System Reacon to Alarm Events e-mail with aachment, saving le on FTP server, saving le on SD card,

alarm output acvaon

Restoring default sengs via web browser, using reset buon, via NMS IPTool soware

IR LED

LED Number 30

Range 30 m

Angle 90°

Smart IR yes (soware support)

INTERFACES

Audio Input/Output 1 x Jack (3.5 mm)/1 x Jack (3.5 mm) built-in microphone

Alarm Input/Output 1 (NO/NC)/1 relay type

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot microSD - capacity up to 128GB

INSTALLATION PARAMETERS

Dimensions (mm) 122 (Ф) x 96 (H)

Weight 0.38 kg

Enclosure plasc, white

Power Supply PoE, 12 VDC

Surge protecon TVS 4000 V

Power Consumpon 3 W, 6 W (IR on)

Operang Temperature -10°C ~ 40°C

Humidity max. 95%, relave (non-condensing)

NVIP-2D-6502/F Quick start guide version 1.0

START-UP AND INITIAL CONFIGURATION

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

2.START-UP AND INITIAL CONFIGURATION

2.1. Description of connectors

1. 100 Mb/s Ethernet port (RJ-45

connector)

2. Audio output (HP)

3. Audio input (MIC)

4. Alarm Connectors

1. Alarm output COM

2. Alarm output

3. Alarm input

4. Alarm input GND

5. Power supply 12VDC

2.2. Description of the camera components

INFORMATION! To access the above items

(except the microphone), remove the camera

cover.

1. Light sensor

2. Infrared LEDs

3. Lens adjustment levers

4. Reset button

5. MicroSD card slot

6. Build in microphone

NVIP-2D-6502/F Quick start guide version 1.0

2.3. Zoom and focus adjustment

To set the focus and focal length, remove the top

cover and then use the available levers to adjust the

field of view and focus.

2.4. Connecting ethernet cable

To maintain tightness of ethernet cable connection, please follow instruction below:

1. Loosen the nut (a) from the main element (b).

2. Run power cable (without RJ-45 connector) though both elements. Then crimp the cable with RJ-45

connector.

3. Connect the cable to the hermetic connector (c), screw main cover (b), then screw the nut (a).

Warning! The 12VDC power connector, the audio and alarm I/O connectors are not hermetic. The user

should ensure the tightness of these sockets on his own.

START-UP AND INITIAL CONFIGURATION

Zoom

Focus

NVIP-2D-6502/F Quick start guide version 1.0

2.5. Connecting power supply to the camera.

The camera can be powered by an external power supply with parameters compatible with the camera

data or by the RJ45 network socket using PoE technology (IEEE 802.3af). To power the camera via

PoE, use a network switch or PoE adapter compatible with the IEEE 802.3af standard.

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user’s

manual.

CAUTION:

Do not use power supplies and POE adapters not compatible with IEEE 802.3af standard!

Damage resulting from the use of improper power supply is not covered under warranty!

In order to provide protection against voltage surges/lightning strikes, usage of appropriate

surge protectors is advised. Any damages resulting from surges are not eligible for service

repairs.

2.6. Camera mounting

1. Remove dome cover by turning it counterclockwise

2. Put assembly template of the camera to the desired mounting

surface, and mark drilling holes.

3. Drill mounting, cable and heat removal holes (1) in

previously selected points.

4. Mount the camera base using included screws on smooth

surface

5. Adjust the position of the camera module.

6. Adjust focal length and focus using proper levers.

7. Put on the camera cover again, by turning it clockwise.

START-UP AND INITIAL CONFIGURATION

12 VDC +

GND

Inhaltsverzeichnis

Sprachen:

Andere Novus IP-Kamera Handbücher

Novus

Novus NVIP-2DN7020SD-2P Bedienungsanleitung

Novus

Novus NVIP-ATM200 Bedienungsanleitung

Novus

Novus NVIP-TDN3401H/IR/MPX2.0 Bedienungsanleitung

Novus

Novus NVIP-7000 series Bedienungsanleitung

Novus

Novus NVIP-2C5000ATM Bedienungsanleitung

Novus

Novus 2000 series Bedienungsanleitung

Novus

Novus NVIP-1DN3000H/IR-1P-II Bedienungsanleitung

Novus

Novus NVIP-5VE-6402M/F Bedienungsanleitung

Novus

Novus NVIP-5VE-4231 Bedienungsanleitung

Novus

Novus NVIP-4DN3060H/IR-1P Bedienungsanleitung

Novus

Novus VIP-12DN7023V/IR-1P Bedienungsanleitung

Novus

Novus NVIP-6DN7000C-1P Bedienungsanleitung

Novus

Novus NVIP-2DN7460H/IRH-2P Bedienungsanleitung

Novus

Novus NVIP-3DN7540D/IRH-2P Bedienungsanleitung

Novus

Novus NVIP-2DN5020SD/IRH-2 Bedienungsanleitung

Novus

Novus NVIP-5V-6502M/F Bedienungsanleitung

Novus

Novus NVIP-12DN7560V/IRH-2P Bedienungsanleitung

Novus

Novus NVIP-3000 Series Bedienungsanleitung

Novus

Novus NVIP-5000 series Bedienungsanleitung

Novus

Novus NVIP-5000 series Bedienungsanleitung

Novus

Novus NVIP-3000 Series Bedienungsanleitung

Novus

Novus NVAHD-2DN5104MH/IRH-2 Bedienungsanleitung

Novus

Novus NVIP-3DN3520SD/IRH-2 Bedienungsanleitung

Novus

Novus NVAHD-2DN3102SD/IR-1 Bedienungsanleitung

Beliebte IP-Kamera Handbücher anderer Marken

FLIR

FLIR Exx series Bedienungsanleitung

Avigilon

Avigilon H4A-BO1-IR Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWCA-C128-64 Bedienungsanleitung

ShareTech

ShareTech AV1 Bedienungsanleitung

Ezviz

Ezviz C6C Bedienungsanleitung

Melchioni

Melchioni UCAM 2015 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ESD-4630 Bedienungsanleitung

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Bedienungsanleitung

Mitel

Mitel 6800i Series Service-Handbuch

Vitek

Vitek VTC-IR403-212NP Bedienungsanleitung

THOMSON

THOMSON DSC - 323W Bedienungsanleitung

AVer

AVer FB2027 Bedienungsanleitung

ENFORCER

ENFORCER EV-T5105-N2SQ Bedienungsanleitung

Wansview

Wansview NC543 Bedienungsanleitung

Eneo

Eneo MCB-64A0003M0A Bedienungsanleitung

deView electronics

deView electronics CBDNI36F Bedienungsanleitung

Swann

Swann SwannEye Bedienungsanleitung

LevelOne

LevelOne IP CamSecure Bedienungsanleitung