Novus NVIP-3DN3552H/IR-1P Bedienungsanleitung

U ser’s manual

( short form)

NVIP-3DN3552H/IR-1P

NVIP-3DN3552H/IR-1P - User’s manual (short form) ver 1.0.

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives

CE Marking

Our products are manufactured to comply with requirements of the following directives and national regulations

implementing the directives:

 Electromagnetic compatibility EMC 2004/108/EC.

 Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as

75VDC and 1500VDC.

WEEE Directive 2012/19/EU

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste Electrical and Electronic

Equipment (2012/19/EU) and further amendments. By ensuring this product is disposed of correctly, you will

help to prevent potential negative consequences for the environment and human health, which could otherwise

be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

RoHS Directive 2011/65/UE

Out of concern for human health protection and friendly environment, we assure that our products

falling under RoHS Directive regulations, regarding the restriction of the use of hazardous

substances in electrical and electronic equipment, have been designed and manufactured in

compliance with the above mentioned regulations. Simultaneously, we claim that our products have

been tested and do not contain hazardous substances whose exceeding limits could have negative

impact on human health or natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN

USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES

NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE

CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR

THE RESULTS OF SUCH AN ACTION.

NVIP-3DN3552H/IR-1P - User’s manual (short form) ver 1.0.

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO

USER-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE

PERSONNEL MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,

damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions

described in the manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual.

NVIP-3DN3552H/IR-1P - User’s manual (short form) ver 1.0.

TABLE OF CONTENTS.................................................................................................4

1. FOREWORD INFORMATION..................................................................................5

1.1. General characteristics .....................................................................................5

1.2. Technical specification ....................................................................................6

1.3. Camera dimension ...........................................................................................7

1.4. Package contents..............................................................................................7

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................8

2.1. Description of connectors and control tools ......................................................8

2.2. Cameras mounting ...........................................................................................9

2.3. Desiccant mounting guide ..............................................................................10

2.4. Starting the IP camera ....................................................................................12

3. NETWORK CONNECTION UTILIZING WEB BROSWER ...............................14

3.1. Recommended PC specification for web browser............................................14

3.2. Connection with IP camera via web browser...................................................14

4. USING AND CONFIGURING..................................................................................16

4.1. Remote Preview Interface. ..............................................................................16

5. ELECTRIC CONNECTORS AND ACCESORIES ...............................................17

5.1. Connecting power supply to the camera. ........................................................17

5.2. Camera control RS..........................................................................................17

5.3. Connecting alarm inputs/outputs.....................................................................17

5.4. SD card installation.........................................................................................18

6. RESTORING FACTORY DEFAULTS ..................................................................19

6.1. Restoring software factory defaults .................................................................19

6.2. Restoring factory defaults by hardware means ................................................19

TABLE OF CONTENTS

NVIP-3DN3552H/IR-1P - User’s manual (short form) ver 1.0.

1. FOREWORD INFORMATION

1.1. General Characteristics

 Imager resolution: 3 megapixels

 Mechanical IR cut filter ,IR operation capability

 Min. Illumination from 0 lx with IR LED on

 Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

 Digital Noise Reduction (DNR)

 Lens type: Varfocal, f=7- 22 mm/F=1.4

Built-in LED illuminator: 25 pcs LED (NVIP-3DN3052H/IR-1P)

 Compression: H.264/H.265

 Max video processing resolution: 2048 x 1536

 Multi streaming: compression, resolution, speed and quality defined individually for each video

stream

 RTP/RTSP protocol support for video transmission

 Post-alarm functions

 Hardware motion detection

 ROI Zones

 Built-in webserver: camera configuration through the website

 Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server

(all cameras) and triggering alarm output, saving file on SD/SDHC card

 Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,

playback and remote IP devices administration

 Power supply: 12VDC, PoE (Power over Ethernet)

FOREWORD INFORMATION

NVIP-3DN3552H/IR-1P - User’s manual (short form) ver 1.0.

1.2. Technical specification

FOREWORD INFORMATION

IMAGE

Image Sensor 3 MPX CMOS sensor 1/2.8” SONY

Number of Effective Pixels 2048 (H) x 1536 (V)

Min. Illumination 0.01 lx/F1.4 - color mode

0 lx (IR on) - B/W mode

Electronic Shutter auto/manual: 1/25 s ~ 1/100000 s

Wide Dynamic Range (WDR) yes

Digital Noise Reduction (DNR) 2D, 3D

LENS

Lens Type varifocal, f=7 ~ 22 mm/F1.4

DAY/NIGHT

Switching Type mechanical IR cut filter

Switching Mode auto, manual, time

Switching Schedule yes

Visible Light Sensor yes

NETWORK

Stream Resolution 2048 x 1536 (QXGA), 1920 x 1080 (Full HD), 1280 x 720 (HD), 704 x 576, 640 x 480

(VGA), 480 x 270, 352 x 288 (CIF)

Frame Rate 30 fps for each resolution

Multistreaming Mode 3 streams

Video/Audio Compression H.264, H.265, MJPEG/G.711

Number of Simultaneous Connections max. 10

Bandwidth 40 Mb/s in total

Network Protocols Support HTTP, TCP/IP, IPv4, FTP, DHCP, DDNS, NTP, RTSP, PPPoE, SMTP

ONVIF Protocol Support Profile S (ONVIF 2.3

Camera Configuration from Internet Explorer, Firefox, Chrome, Opera browser

languages: Polish, English, Russian, and others

Compatible Software NMS

OTHER FUNCTIONS

Privacy Zones 4

Motion Detection yes

Region of interest (ROI) 8

Image Processing 90˚ image rotation, 180˚ image rotation, sharpening, mirror effect

Prealarm/Postalarm -/up to 120 s

System Reaction to Alarm Events e-mail with attachment, saving file on FTP server, saving file on SD card, alarm output

activation

IR LED

LED Number 25

Range 70 m

Angle 60°

INTERFACES

Video Output BNC, 1.0 Vp-p, 75 Ohm - maintenance only

Audio Input/Output 1 x Jack (3.5 mm)/1 x Jack (3.5 mm)

Alarm Input/Output 1 (NO/NC)/1

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot SD

INSTALLATION PARAMETERS

Dimensions (mm) with bracket: 109 (Ф) x 360 (L)

Weight 1.7 kg

Degree of Protection IP 66

Enclosure aluminium, white, fully cable manged wall mount bracket in-set included

Power Supply PoE, 12 VDC

Power Consumption 2.5 W

6 W (IR on)

Operating Temperature -20°C ~ 50°C

NVIP-3DN3552H/IR-1P - User’s manual (short form) ver 1.0.

FOREWORD INFORMATION

1.3. Camera dimensions

1.4. Package contents

After you open the package make sure that the following elements are inside:

 IP camera

 Accessories bag

 Short version of user’s manual

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

NVIP-3DN3552H/IR-1P - User’s manual (short form) ver 1.0.

1.4. Package contents

After you open the package make sure that the following elements are inside:

 IP camera

 230 VAC / 12 VDC power supply

 Accessories bag

 Short version of user’s manual

 CD containing manual and software

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

2. START-UP AND INITIAL CAMERA CONFIGURATION

2.1 Description of connectors and control tools

1. BNC video output

2. Audio output

3. Audio input

4. Power supply 12VDC

5. 100 Mb/s Ethernet port (RJ-45 connector)

6. Alarm COM - Alarm output

7. Alarm NO - Alarm output

8. Alarm IN - Alarm input

9. Alarm GND - Alarm input

10. RS485 T+

11. RS485 T-

START-UP AND INITIAL CAMERA CONFIGURATION

5 6

NVIP-3DN3552H/IR-1P - User’s manual (short form) ver 1.0.

WARNING! To get access to above ports it is required to open service compartment.

1. 3 pin connector. Video output and power supply - maintenance only

2. Reset button

3. Network indicator

4. SD card slot

2.2 Zoom and focus adjustment

User can adjust camera zoom and focus. It is recommended to check focus settings in infrared

illumination and make correction in color mode to have proper focus in both modes.

START-UP AND INITIAL CAMERA CONFIGURATION

1 2

Zoom adjustment Focus adjustment

NVIP-3DN3552H/IR-1P - User’s manual (short form) ver 1.0.

2.3 Camera mountain

WARNING! In order to obtain declared degree of protection please seal the camera bracket to prevent

water getting inside. Furthermore, when installing the bracket on rough/uneven surfaces, please

additionally seal the junction with appropriate sealing mass. Please pay special attention to any

mounting holes and if they are a loop-through ones, seal them too.

To mount a camera please follow the instructions below:

1. Drill the screw holes and the cable hole on the wall according to the drill template.

2. Route the cables to the cable hole and connect the cables.

3. Using included screws mounting base on smooth surface providing declared degree of IP protection.

4. Optionally open service compartment to insert SD card and connect monitor through DCIN/CVBS

cables.

5. Using allen key loosen screws 1, 2 and 3. Then adjust camera position and tight lock screws.

6. Adjust zoom and focus screw until you get the optimum image (after starting IP Camera, details in

chapter 2.4).

START-UP AND INITIAL CAMERA CONFIGURATION

1 2 3

Service compartment

Inhaltsverzeichnis

Sprachen:

Andere Novus Sicherheitskamera Handbücher

Novus

Novus NVIP-2DN3000C-1P Bedienungsanleitung

Novus

Novus NVIP-3DN3012V/IR-1P Bedienungsanleitung

Novus

Novus NVIP-5H-4202 Bedienungsanleitung

Novus

Novus NVB-6030FMB Bedienungsanleitung

Novus

Novus NVIP-2DN2101H/IR-1P Bedienungsanleitung

Novus

Novus NVH-160H/12/24 Bedienungsanleitung

Novus

Novus NVIP-2H-6511/F Bedienungsanleitung

Novus

Novus NVIP-1DN3000H/IR-1P Bedienungsanleitung

Novus

Novus NVDN-201D/IR Bedienungsanleitung

Novus

Novus NVIP-5V-6401/F Bedienungsanleitung

Novus

Novus NVIP-8H-6202M-II Bedienungsanleitung

Novus

Novus NVDN-402V/IR Bedienungsanleitung

Novus

Novus NVIP-8DN7560H/IRH-2P Bedienungsanleitung

Novus

Novus NVIP-4H-6502M/F-II Bedienungsanleitung

Novus

Novus NVIP-4DN3062V/IR-1P Bedienungsanleitung

Novus

Novus NVIP-4VE-6502M/F Bedienungsanleitung

Novus

Novus NVIP-4DN3552AH/IR-1P Bedienungsanleitung

Novus

Novus NVIP-3DN3050H/IR-1P Bedienungsanleitung

Novus

Novus NVIP-2DN5040V/IR-1P Bedienungsanleitung

Novus

Novus NVAHD-2DN5100MC-3 Bedienungsanleitung

Novus

Novus NVIP-2DN5000H/IR-1P Bedienungsanleitung

Novus

Novus NVIP-2DN5120SD/IRH-2 Bedienungsanleitung

Novus

Novus NVIP-5VE-6202 Bedienungsanleitung

Novus

Novus NVIP-6F-6301-II Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung