Novus NVIP-3SD-6300/30/F Bedienungsanleitung

User’s ma n ual

(sh o r t form)

NVIP-3SD-6300/30/F

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2014/30/EU) and LVD (2014/35/UE) Directives

CE Marking

Our products are manufactured to comply with requirements of the following directives and national

regulations implementing the directives:

• Electromagnetic compatibility EMC 2014/30/EU.

• Low voltage LVD 2014/35/UE with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as

75VDC and 1500VDC.

WEEE Directive 2012/19/EU

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste Electrical and

Electronic Equipment (2012/19/EU) and further amendments. By ensuring this product is disposed of

correctly, you will help to prevent potential negative consequences for the environment and human health, which

could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

RoHS Directive 2011/65/EU

Out of concern for human health protection and friendly environment, we assure that our products falling under

RoHS Directive regulations, regarding the restriction of the use of hazardous substances in electrical and

electronic equipment, have been designed and manufactured in compliance with the above mentioned

regulations. Simultaneously, we claim that our products have been tested and do not contain

hazardous substances whose exceeding limits could have negative impact on human health or natural

environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN

USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES

NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE

CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR

THE RESULTS OF SUCH AN ACTION.

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER

-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL

MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,

damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual;

10. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions

described in the manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual.

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

TABLE OF CONTENTS.....................................................................................................4

1. FOREWORD INFORMATION .....................................................................................5

1.1. General characteristics.........................................................................................5

1.2. Technical specification .......................................................................................6

1.3. Camera dimension ..............................................................................................7

1.4. Package contents..................................................................................................7

2. START-UP AND INITIAL IP CAMERA CONFIGURATION .................................8

2.1. Description of connectors and control tools ........................................................8

2.2. Connecting ethernet cable ...................................................................................9

2.3. Camera mounting ..............................................................................................10

2.4. Starting the IP camera........................................................................................11

2.5. Initial configuration via the web browser..........................................................12

2.6 Security recommendations for network architecture and configuration ...........13

3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................14

3.1. Recommended PC specification for web browser .............................................14

3.2. Connection with IP camera via web browser.....................................................14

4. WWW INTERFACE - WORKING WITH IP CAMERA.........................................16

4.1. Displaying live video..........................................................................................16

4.2. PTZ camera control . ..........................................................................................17

5. ELECTRIC CONNECTORS AND ACCESORIES .................................................18

5.1. SD card installation ...........................................................................................18

5.2. Alarm input and output connection ....................................................................18

6. RESTORING FACTORY DEFAULTS .....................................................................19

6.1. Restoring software factory defaults via web browser ........................................19

6.2. Restoring software factory defaults via NMS IPTool……… ..………………..19

6.3 Restoring hardware factory defaults by hardware..………………..…………...20

TABLE OF CONTENTS

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

1. FOREWORD INFORMATION

1.1. General Characteristics

• Integrated speed dome camera day/night

• Mechanical IR cut filter

• Ability to work in the infrared-built-in IR LED

• Resolution of the sensor: 3.0 megapiksels

• Sensitivity: from 0,01 Lux with IR Off

• Lens type: motor-zoom with automatic Iris and auto-focus f=4.5-135mm/F1.6-F4.4

• 8 patrols (16 presets)

• 4 patterns (up to 180 seconds )

• Time tasks: 8

• 2 scanning modes

• 360 presets

• Optical Zoom: 30x

• 7 alarm input

• 1 alarm output (NO/NC)

• MicroSD card up to 128GB

• OSD menu

• Auto-flip

• Compression method H.264, H.265 or MJPEG

• Dual audio

• Vide resolution: 2048 x 1536

• Support RTP/RTSP standard

• Support up to 3 streams

• Network connection control

• Build in web server - possibility to configure camera trough web browser

• Ability to broadly define the system's response to alarm events: email with attachments, save file

to FTP server, trigger alarm output, HTTP notification, PTZ function call

• Full PTZ operational via internet browser or NMS software (NOVUS MANAGEMENT

SYSTEM)

• Protocol support: ONVIF Profile S/R, TCP/IP, UDP, DHCP, DDNS, NTP, RTSP, SMTP, FTP,

PPPoE

• Software: NMS (NOVUS MANAGEMENT SYSTEM - recording, live preview, playback of

recording and much more)

• Wall bracket included

• Power Supply: 24 VDC or 24VAC

• Face recognition - advanced analytic function, available only with selected models of the NVR

6000 series.

FOREWORD INFORMATION

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

1.2. Technical specification

FOREWORD INFORMATION

IMAGE

Image Sensor 3 MPX CMOS sensor 1/2.8” SONY Exmor R STARVIS

Number of Effective Pixels 2065 (H) x 1553 (V)

Min. Illumination 0.03 lx/F1.6 - color mode,

0.01 lx/F1.6 - B/W mode,

0 lx (IR on) - B/W mode

Electronic Shutter auto: 1/25 s ~ 1/100000 s

Wide Dynamic Range (WDR) yes (double scan sensor), 120dB

Digital Noise Reduction (DNR) 3D

Defog Function (F-DNR) yes

Highlight Compensation (HLC) yes

Back Light Compensation (BLC) yes

LENS

Optical Zoom 30x

Lens Type motor-zoom, auto-iris function, f=4.5 ~ 135 mm/F1.6 ~ F4.4

Auto-focus zoom trigger, day/night mode trigger

DAY/NIGHT

Switching Type mechanical IR cut filter

Switching Mode auto, manual, time

Visible Light Sensor yes

NETWORK

Stream Resolution 2048 x 1536 (QXGA), 1920 x 1080 (Full HD), 1280 x 720 (HD), 640 x

480 (VGA), 320 x 240 (QVGA)

Frame Rate 30 fps for 2048 x 1536 (QXGA) and lower resolutions

Multistreaming Mode 3 streams

Video/Audio Compression H.264, H.265, MJPEG/G.711

Number of Simultaneous

Connections max. 6

Bandwidth 70 Mb/s in total

Network Protocols Support HTTP, TCP/IP, IPv4/v6, Multicast, FTP, DHCP, DNS, DDNS, NTP, RTSP,

RTP, UPnP, SNMP, QoS, IEEE 802.1X, PPPoE, SMTP, SSL, ICMP, Unicast

ONVIF Protocol Support Profile S/G

Camera Configuration from Internet Explorer browser

languages: Polish, English

Compatible Software NMS, NVR-6000 Viewer

Mobile applications SuperLive Plus (iPhone, Android)

PTZ

Preset Commands 360

Tours 8 (up to 16 presets per tour)

Auto-Scans 2

Patterns 4 (max. 180 s for each pattern)

Tilt/Pan Range 0° ~ 93°/360° (continuous)

Pan/Tilt Speed up to 80°/s (proportional to zoom)

Preset Speed up to 150°/s

Protocols Pelco-D, Pelco-P

OTHER FUNCTIONS

Access Password number of characters: 4 numbers

Privacy Zones 4

Motion Detection yes

Video Content Analysis (VCA) face detection

Image Processing 180˚ image rotation, sharpening, mirror effect

System Reaction to Alarm Events e-mail with attachment, saving file on SD card, alarm output

activation, HTTP notification, PTZ

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

FOREWORD INFORMATION

1.3. Camera dimensions (mm)

Camera NVIP-3SD-6300/30/F

1.4. Package contents

After you open the package make sure that the following elements are inside:

• IP camera

• Accessories bag

• Short version of user’s manual

• Wall bracket

• 24VAC Power supply

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

It is forbidden to use – as the camera signal source – PoE equipment (adapters, etc.) not

compatible with IEEE 802.3at/af standard (items called “passive PoE power supply”). Damages

that results from the usage of improper power supply source are not covered by the warranty.

IR LED

LED Number 10

Range up to 180 m (depends on current optical zoom value)

Angle up to 45° (depends on current optical zoom value)

INTERFACES

Audio Input/Output 1 x Jack (3.5 mm)/1 x Jack (3.5 mm)

Alarm Input/Output 7 (NO/NC)/1 relay type

RS-485 yes

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot microSD - capacity up to 128GB

INSTALLATION PARAMETERS

Dimensions (mm) 216 (Ф) x 348 (H) with bracket: 216 (W) x 385 (H) x 350 (L)

Weight 5.4 kg with bracket: 6.1 kg

Degree of Protection IP 66 (details in the user’s manual)

Enclosure aluminium, white, IK10 impact rating, in set: outdoor housing

(integrated with the camera), wall mount bracket

Power Supply 24 VDC/24 VAC

Power Consumption 15 W, 35 W (IR on), 65 W (IR and heater on)

Surge protection TVS 6000 V

Operating Temperature -30°C ~ 60°C

Built-in Heater/Fan yes/no

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

START-UP AND INITIAL IP CAMERA CONFIGURATION

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

2.1 Description of connectors and control tools

1. 100 Mb/s Ethernet port (PoE RJ-45 connector)

2. Audio input (Jack 3.5mm)

3. Audio output (Jack 3.5mm)

4. BNC CVBS video output

5. Alarm input/output terminal block

6. RS485 terminal block

7. Power supply 24VAC/24VDC

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

START-UP AND INITIAL IP CAMERA CONFIGURATION

2.2. Connecting ethernet cable

To maintain tightness of ethernet cable connection, please follow instruction below:

1. Unscrew the nut (2) from the connector cover (1), mount the sealing ring on the socket (3).

2. Route the network cable through the components (1) and (2). Plug the RJ-45 connector into the

socket (3).

3. Screw the connector cover (1) on the socket (3). Inside the upper part of the connector cover (1) push

in to the stop the seal of the cable (4) - the seal is cut to insert on the network cable.

4. Tighten up to the stop nut (2).

CAUTION!

The declared degree of protection of the camera relates to its housing and does not take into

account the possibility of moisture infiltration into the interior of the camera by connecting

cables. Connection cables protection through i.e. sealing up is the responsibility of the camera

installer. The manufacturer is not liable for any damages to the camera caused as a result of

failing in performing that activity by installer, which also means that camera damaged in that

way is not subject to warranty repairs.

Camera power supply connector is not hermetic. User should seal this connector by himself.

Camera can be supplied using external power supply unit corresponding with the camera parameters

CAUTION!

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

Schema of 12VDC power supply connector

NVIP-3SD-6300/30/F - User’s manual (short form) ver 1.0

2.3. Camera mounting

To mount a camera please follow the instructions below:

• Unscrew the top camera part and unplug wires (1).

• Put the bracket to the wall in a desired mounting place (with cable hole). Take the drill pattern

and mark future drilling holes for screws and wires.

• Drill holes in accordance with previously done markings and base hole placement.

• Mount the camera bracket using the supplied plugs and screws.

• Mount the muff to the bracket (2).

• Mount top camera part to the muff (3).

• Mount camera to the bracket (mount to hinge) and plug in wires. Move camera to bracket and

tighten to the stop counter screws (4).

CAUTION!

Please note that the wall or ceiling must have enough strength to support the IP Camera.

CAUTION!

In order to obtain declared degree of protection please seal the camera bracket to prevent water

getting inside. Furthermore, when installing the bracket on rough/uneven surfaces, please

additionally seal the junction with appropriate sealing mass. Please pay special attention to any

mounting holes and if they are a loop-through ones, seal them too.

START-UP AND INITIAL CAMERA CONFIGURATION

Inhaltsverzeichnis

Sprachen:

Andere Novus Sicherheitskamera Handbücher

Novus

Novus NVC-401D-black Bedienungsanleitung

Novus

Novus NVIP-2VE-4231/WL Bedienungsanleitung

Novus

Novus NVIP-5DN2021D/IR-2P Bedienungsanleitung

Novus

Novus NVIP-2D-6402 Bedienungsanleitung

Novus

Novus NVIP-2V-6501/F-II Bedienungsanleitung

Novus

Novus NVAHD-2DN5202MH/IR-1 Bedienungsanleitung

Novus

Novus NVIP-2DN3133V/IR-1P Bedienungsanleitung

Novus

Novus NVIP-2VE-4201/PIR Bedienungsanleitung

Novus

Novus NVIP-2DN3134V/IR-1P Bedienungsanleitung

Novus

Novus NVIP-12DN7021V/IR-1P Bedienungsanleitung

Novus

Novus NVIP-4DN3517V/IR-1P Bedienungsanleitung

Novus

Novus NVIP-4VE-6501/F Bedienungsanleitung

Novus

Novus NVIP-2C2001D-P/GO Bedienungsanleitung

Novus

Novus NVC-60CH Bedienungsanleitung

Novus

Novus NVIP-5VE-4402/F Bedienungsanleitung

Novus

Novus NVAHD-1DN3101D/IR-1 Bedienungsanleitung

Novus

Novus 5000 VSS MULTI HD Bedienungsanleitung

Novus

Novus NVIP-2DN3131H/IR-1P Bedienungsanleitung

Novus

Novus NVIP-8VE-6202M-II Bedienungsanleitung

Novus

Novus NVIP-2DN2101H/IR-1P Bedienungsanleitung

Novus

Novus NVIP-2DN5040V/IR-1P Bedienungsanleitung

Novus

Novus NVIP-5H-6412M/F Bedienungsanleitung

Novus

Novus NVIP-2H-4231/PIR Bedienungsanleitung

Novus

Novus NVDN-801D Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung