Ntron 100-POE4-MDR Montage- und Bedienungsanleitung
(Revised 2011-09-02)
1
100-POE4
Unmanaged Industrial 4-Port
Mid-Span POE PSE
User Manual &
Installation
Guide
(Revised 2011-09-02)
2
Industrial 4-Port Mid-Span POE PSE Installation Guide
100-POE4
(Revised 2011-09-02)
3
Copyright, © N-TRON Corp., 2008
820 S. University Blvd., Suite 4E
Mobile, AL USA 36609
All rights reserved. Reproduction, adaptation, or translation without prior written permission from N-TRON
Corp. is prohibited, except as allowed under copyright laws.
Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos
or other designations mentioned herein are trademarks of their respective owners.
The information contained in this document is subject to change without notice. N-TRON Corp. makes no
warranty of any kind with regard to this material, including, but not limited to, the implied warranties of
merchantability or fitness for a particular purpose. In no event shall N-TRON Corp. be liable for any
incidental, special, indirect or consequential damages whatsoever included but not limited to lost profits
arising out of errors or omissions in this manual or the information contained herein.
Contact Information :
N-TRON Corp.
820 South University Blvd.
Suite 4E
Mobile, AL 36609
TEL: (251) 342-2164
FAX: (251) 342-6353
Website: www.n-tron.com
Email: [email protected]
(Revised 2011-09-02)
4
GENERAL SAFETY WARNINGS
WARNING: Do not operate the equipment in the presence of flammable gasses or fumes. Operating
electrical equipment in such an environment constitutes a definite safety hazard.
WARNING: If the equipment is used in the manner not specified by N-TRON Corp., the protection provided
by the equipment may be impaired.
WARNING: Do not perform any services on the unit unless qualified to do so. Do not substitute
unauthorized parts or make unauthorized modifications to the unit.
WARNING: Do not operate the unit with the end plates removed, as this could create a shock or fire
hazard.
WARNING: Properly ground the unit before connecting anything else to the unit. Units not properly grounded
may result in a safety risk and could be hazardous and may void the warranty. See the grounding technique
section of this user manual for proper ways to ground the unit.
WARNING: Do not operate the equipment in a manner not specified by this manual.
ENVIRONMENTAL SAFETY WARNINGS
WARNING: Disconnect the power and allow to cool 5 minutes before touching.
ELECTRICAL SAFETY WARNINGS
WARNING: Disconnect the power cable before removing the end plates.
WARNING: Do not operate the unit with the end plates removed.
WARNING: Do not work on equipment or cables during periods of lightning activity.
WARNING: Do not perform any services on the unit unless qualified to do so.
WARNING: Observe proper DC Voltage polarity when installing power input cables. Reversing voltage
polarity can cause permanent damage to the unit and void the warranty.
(Revised 2011-09-02)
5
HAZARDOUS LOCATION INSTALLATION REQUIREMENTS
1. This equipment is suitable for use in Class I, Div 2, Groups A, B, C, and D, or unclassified or non-
hazardous locations only.
2. WARNING: Explosion Hazard - Substitution of components may impair suitability for Class I,
Division 2.
3. WARNING: Explosion hazard, do not disconnect while the circuit is live or unless the area is known to be
non-hazardous.
4. WARNING: Explosion Hazard - Do not remove or replace the device unless power has been switched off
or the area is known to be non-hazardous.
5. Use 60/75ºC rated Copper wire, (0.22Nm) 2 inch-lbs Tightening torque for field installed connectors.
6. WARNING: Install only in accordance with Local & National Codes of Authorities Having Jurisdiction.
7. Class I, Div 2 installations require that all devices connected to this product must be UL listed for the area in
which it is installed.
8. WARNING: Damage may occur to the RJ-45 port of the powered device (PD), if the 100-POE4 is not
powered down before disconnecting the Cat5E cable.
(Revised 2011-09-02)
6
Functional Overview
The 100-POE4 industrial 4-port Mid-Span POE PSE is designed to provide power over Ethernet for POE
capable devices where running a power line is either not possible or not cost effective. This feature allows
an end user to power a POE camera, wireless access point, or any other POE capable device without the
need for running separate wires for power. This also allows the ability for a centralized battery backup for
all these devices.
Key Features
Compact, space saving package
IEEE 802.3af Compliant
Four 10/100Base-TX RJ-45 Ports (DATA IN)
Four 10/100Base-TX RJ-45 POE Ports (DATA & POWER OUT)
Unmanaged operation
Extended Environmental Specifications
-40°C to 85°C Operating and Storage Temperature
Operating Humidity: 10% to 90% (Non Condensing)
Full Wire Speed Communications
LED POE Status Indication
Power Fault Status LEDs
Up to 0.8 Gb/s Maximum Throughput
Industry Standard 35mm DIN Rail Mounted Enclosure
Redundant power inputs (46-49 VDC)
Supports up to 15.4Watts per channel (13 Watts at the Powered Device (PD ))
Hardened metal DIN Rail Enclosure
(Revised 2011-09-02)
7
PACKAGE CONTENTS
Please make sure the package contains the following items:
1. 100-POE4
2. Instruction Sheet
Contact your carrier if any items are damaged.
UNPACKING
Remove all the equipment from the packaging, and store the packaging in a safe place. File any damage
claims with the carrier.
CLEANING
Clean only with a damp cloth.
INSTALLATION
Read the following warnings before beginning the installation:
WARNING
Never install or work on electrical equipment or cabling during periods of lightning activity. Never connect
or disconnect power when hazardous gasses are present.
(Revised 2011-09-02)
8
DIN-Rail Mounting
Install the unit in a standard DIN rail. Recess the unit to allow at least 2” of horizontal clearance for CAT5e
cable bend radius.
To install the unit to 35mm industrial DIN rail,
place the top edge of the included mounting
bracket on the back of the unit against the DIN
rail at a 15° angle as shown. Rotate the bottom of
the unit to the back (away from you) until it
snaps into place.
To remove the unit from the 35mm industrial
DIN rail, place a flat head screwdriver into the
release clip found at the bottom of the unit, and
apply downward force on the clip until it
disengages from the bottom of the unit from the
DIN rail. Rotate the bottom of the unit towards
you and up at an approximate 15° upward angle
to completely remove the unit.
Most N-Tron™ products are
designed to be mounted on industry
standard 35mm DIN rail. However,
DIN rail mounting may not be
suitable for all applications. Our
Universal Rack Mount Kit (P/N:
URMK) may be used to mount the
100-POE4 enclosures to standard 19"
racks as an option.
(Revised 2011-09-02)
9
FRONT PANEL
From Top to Bottom:
Power LED
V1 POE POE is being applied on the respective port with V1 as a valid source of power.
V2 POE is being applied on the respective port with V2 as a valid source of power.
LEDs: The table below describes the operating modes (Port LEDs are for power supply status only and
do NOT indicate link or activity):
Note: Redundant power inputs will not balance the power load. Only load from one power supply is used
at a time.
(Revised 2011-09-02)
10
APPLYING POWER (Top View)
Unscrew & Remove the DC Voltage Input Plug from the top header.
Install the DC Power Cables into the Plug (observing polarity on unit).
Plug the Voltage Input Plug back into the top header.
Tightening torque for the terminal block power plug is 0.22 Nm/0.162 Pound Foot.
Turn the power on the wire.
Note: It is only safe to turn the power on the wires after the wires have been secured to the
100-POE4.
WARNING: Inserting the input plug while the 48VDC is applied may cause arcing, and damage
the input connector permanently.
Verify the Power LED stays ON (GREEN).
Note: Either V1or V2can be connected to power for minimal operation. For redundant power
operation, V1and V2plugs must be connected to separate DC Voltage sources. Use wire sizes of 20-10
gauge. The power cord should be limited to less than 10 meters in order to ensure optimum
performance.
Recommended 48V DC Power Supplies, similar to:
100-240VAC:
N-Tron NTPS-48-5, DC 48V/5A or N-Tron NTPS-48-2, DC 48V/2A
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Ntron Schalten Handbücher
Ntron
Ntron 302MC-XX Bedienungsanleitung
Ntron
Ntron 600 Series Bedienungsanleitung
Ntron
Ntron 105FX-POE Montage- und Bedienungsanleitung
Ntron
Ntron 7014 Series Kurzanleitung
Ntron
Ntron 500 Series Bedienungsanleitung
Ntron
Ntron 400 Series Bedienungsanleitung
Ntron
Ntron 100 Series Montage- und Bedienungsanleitung
Ntron
Ntron 508TX Bedienungsanleitung
Ntron
Ntron 608MFX-ST Handbuch
Ntron
Ntron NT24k Bedienungsanleitung
Ntron
Ntron 7018TX Montage- und Bedienungsanleitung
Ntron
Ntron 7014TX Montage- und Bedienungsanleitung
Ntron
Ntron 708M12 Montage- und Bedienungsanleitung
Ntron
Ntron 105TX-SL Bedienungsanleitung
Ntron
Ntron 709FX Series Montage- und Bedienungsanleitung
Ntron
Ntron 526FX2 Bedienungsanleitung
Ntron
Ntron 100-POE-SPL Montage- und Bedienungsanleitung
Ntron
Ntron 7010TX Series Montage- und Bedienungsanleitung
Ntron
Ntron 405FX-SC Bedienungsanleitung
Ntron
Ntron 7900 Series Montage- und Bedienungsanleitung
