Numatic HT4045 Bedienungsanleitung
Warning! Read instructions before using the machine
Owner Instructions
HT4045
TT4045G
TT4055G
SCRUBBER DRYER
www.numatic.co.uk
SCRUBBER DRYER
Index
HT 4045, TT 4045, TT 4055
Machine Overview ................................ Pages 2-3
Machine Set up Guide ................................ Page 4-7
Tilting the Handle ................................ Page 4
Fitting the Top Tank ................................ Page 4
Fitting the Brush ................................ Page 4
Tipping the Brush Deck ................................ Page 5
Fitting the Floor-tool .............................. Page 5
Fitting the hose guide ................................ Page 6
Fill the Clean-water tank ................................ Page 6
Clean Water Level ................................ Page 7
Control of Cleaning substances (COSHH) ...... Page 7
Clean Water Tap On / O ................................ Page 7
Pre Cleaning ................................ Page 7
Pre Scrubbing ................................ Page 8
Lowering the oor-tool ................................ Page 8
Breakaway oor-tool feature ........................... Page 8
Setting the cleaning controls ....................... Page 9
Regular Maintenance ................................ Page 10
Tanks and Filters ................................ Page 10
Changing the Floor-tool Blades ................... Page 11
O-Aisle Cleaning Kit ................................ Page 12
Specications ................................ Page 12
HT 4045 Face Fitting ................................ Page 13-14
Trouble Shooting ................................ Page 15
Recommended Spare Parts .......................... Page 15
Schematic Diagram ................................ Page 16
Rating Label / Personal Protective Equipment /
Recycling ................................ Page 17
Safety Precautions ................................ Page 18
EU Declaration Document ............................. Page 19
Warranty ................................ Page 19
Company Address ................................ Page 20
1Operator Control Panel
2Separator
3Top Tank (waste-water)
4Waste-water Emptying Hose
5Bottom Tank (clean-water)
6Deck Locking Pin
7Brush Deck
8Handle Position Lever
9Vacuum Switch
10 Pump Switch
11 Power Light
12 On / Off Switch
13 Triggers
14 Clean-water Tank Fill Point / Filler Hose
15 Floor-tool Vacuum Hose
16 Vacuum Hose
17 Clean-water Tank Emptying Hose & Fill Level
18 Floor-tool Lifting Lever
19 Floor-tool Retaining Knobs
20 Semi Parabolic Floor-tool
21 Clean Water Filter
22 Brush
PLEASE READ
BEFORE COMMENCING
OPERATION
After the removal of all the
packaging, carefully open
and check the contents
● Owner Manual
● Scrub Brush
●Semi Parabolic Floor-tool
●Floor-tool Hose
Machine Overview
1
3
4
5
6
7
8
10
13
14 14
15
16
17
18
19
20
21
11
2
22
9
12
13
19
8
Machine Set Up
4
www.numatic.co.uk
Tilting the handle
Using the handle position lever (Fig.1).
Fit the top tank to the machine (Fig.3).
Fitting top tank
1
2
3
4
PLEASE READ BEFORE COMMENCING ANY OPERATION AFTER THE REMOVAL OF ALL
THE PACKAGING, CAREFULLY OPEN AND CHECK THE CONTENTS. !!
Move the handle into the upright position (Fig.2).
Fit both vacuum and oor-tool hose to the separator (Fig.4).
Vacuum hose
Floor-tool hose
Fitting the brush - Safety gloves are recommended for the changing of used brushes.
Featuring the Nulock brush system. The brush is simply pushed and twisted to lock, making tting and removal a simple
process. The Pad is retained using Numatic’s own PadLoc system (ask your supplier for details).
Only use manufacturer supplied brushes / pads. TT 4045G requires a 450mm brush or a 400mm pad. TT 4055G requires a 550mm
brush or a 500mm pad. Fit the brush / pad to the drive chuck, twist to lock the brush (Fig.5) / pad in place (Fig.6).
5
6
Machine Set Up
5
T 01460 68600
Tipping the Brush Deck
Fitting the Floor-tool
The oor-tool has been designed for quick tting, allowing easy squeegee blade replacement and a safety knock-o feature if the oor-
tool gets snagged, whilst in transit.
Note: It is easier to t the oor-tool if the weight of the machine is resting on the brush. Ensure the brush is tted rst.
Raise the oor-tool for transit or lower for cleaning opera-
tion using the lifting handle tted to the back of the machine
(Fig.11).
For tting the oor-tool blades (See Page 13).
11
To tip the deck into the down position (Operating mode). Press
in the brush deck locking pin (Fig.7) and rotate the brush deck
(Fig.8).
7
8
To change to brush deck up position, (Transit mode) simply
lift the deck and the sprung loaded locking pin will activate to
hold the deck up.
!! ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF
BEFORE MAKING ANY ADJUSTMENTS
Fit the oor-tool and retain using the detent pin (Fig.9).
9
10
The lifting strap is held by a detent pin (Fig.10).
Machine Set Up
6
www.numatic.co.uk
The TT Range are all equipped with a 40 litre clean-water tank allowing large areas to be cleaning in a single ll.
Filling the clean-water tank
Ret vacuum hose to the Floor-tool when nished.
The vacuum hose has a U-bend clip which creates a U-bend in the hose preventing water spillage when the vacuum is switched o. If
you need to remove the U-bend clip for any reason always ensure it is retted correctly before you resume operation (Fig 36-39).
30mm
MAX
Fitting the Hose Guide
Note:
DO NOT push the vacuum hose onto the Floor-tool with the Floor-tool in the raised position.
Raise oor-tool again before driving to the cleaning area. !!
Note:
Great care must be taken to ensure that contaminants (leaves,hair, dirt, etc) are not
allowed to enter the clean-water tank during the lling process. If using a bucket or
similar, ensure it is always clean and free from debris.
!!
12
13
The large cap on the left can be
removed for lling from a bucket or
suitable container (Fig.13).
To ll the clean-water tank, use the
FLEXI - FILL pipe from either a tap or
hose pipe (Fig.12).
Fill the clean-water tank
to a maximum of 40 litres,
including cleaning chemicals
if required. Follow chemical
manufactures guide lines.
Machine Set Up
7
T 01460 68600
Control of Substances Hazardous to Health (COSHH)
For best results use a non-foaming type of chemical, dilute to the manufacturer’s specication.
For further guidance on hazardous substances refer to health and safety instructions online.
Visit http://www.hse.gov.uk/ for UK information.
Turn on the clean-water tap. On
Off
Clean water tap
The water level in the clean-water tank
can be seen using the clean-water
clear dump hose tted to the rear of the
machine.
The clean-water bottom tank holds 40 litres.
Clean water level
MAX
WHEN HANDLING AND MIXING CHEMICALS
Always ensure that chemical manufacturer’s safety guidelines are followed.
Only use chemicals recommended for use in auto scrubber-dryers.
IMPORTANT
Do not operate machine unless the Operator Manual has been read and fully understood.
!!
Numatic part (629044) Wet Floor sign
(available if required)
Before performing the cleaning operation, place out
appropriate warning signs and sweep or dust-mop the oor (Fig.14).
14
Pre-cleaning advice
!! ALWAYS ENSURE THAT THE FLOOR IS PRE-SWEPT
AND RELEVANT SAFETY SIGNS ARE DISPLAYED
Machine Operation
8
www.numatic.co.uk
Lowering the floor-tool
Pre-scrub mode
The TT Range have been designed to cope with a variety of oor types and dierent levels of soiling.
On heavily soiled oors use a ‘double scrub’ technique.
First pre-scrub the oor with the oor-tool in the raised position, allow the chemical time to work, then scrub the area a second time
with the oor-tool lowered.
Floor-tool in use
Breakaway floor-tool
The clean-water / chemical mix is
dispersed via the ‘THRU-FEED’
system.
The waste water is then retrieved
by the oor-tool.
Overlap the scrubbing path by
10cm to ensure an even clean
(Fig.15).
If streaking occurs, wipe the oor-
tool blades clean (Fig.16).
15
16
After preparing the oor (see previous
section), we are now ready to set the
controls to suit the cleaning conditions.
Before any settings can be applied,
ensure the brush deck is lowered.
Move the oor-tool lever (see Fig.17),
to it’s lower position (see Fig.18).
Note: The machine will still reverse
withthe oor-tool in the lowered
position, this could possibly damage
the blades. Raise the oor-tool before
reversing.
17
18
The oor-tool design incorporates a safety knock-o feature.
Allowing it to safely disengage from its mounting should it
become caught on an obstruction, during forward machine
movement.
To re-attach the oor-tool blade to its holder, rst loosen the retaining
knobs on the oor-tool body and slide onto the
holding bracket.
Tighten retaining knobs to nger tight (See Fig.19).
19
Note:
Care must be taken to reduce speed when cornering or when
manoeuvring around obstacles.
Setting The Cleaning Controls
9
T 01460 68600
Ensure your TT machine has been plugged into a suitable power supply.
Select the desired function using the on / o switches tted to the handle.
To start: hold down either trigger and
press the yellow On / O Switch once
Regular Maintenance
10
www.numatic.co.uk
Remove the two hoses to disconnect the separator from the machine (Fig.21).
Lift o the separator. The separator has a sealing-rubber which should be
examined at every clean-down (Fig.22).
Rinse using clean-water.
Remove the lter tted into the separator and ush with clean-water (Fig.23)
(Fig.24).
Placed into the top tank is grey lter basket, clean and ush with clean-water
(Fig.25) (Fig.26).
21
22
25
26
23
24
The bottom (clean-water) tank is attached to the chassis and should only be removed by a competent service engineer (Fig.27).
Clean by ushing with clean-water if required.
Excess water can be drained using the clear dump hose tted to the rear of the machine.
Located under the left hand side is a clean-water lter, ensure the clean water tap is turned o
before removing this lter (Fig.28).
Clean and ush with clean-water if required.
27
28
ALWAYS ENSURE THAT THE BATTERY IS DISCONNECTED
PRIOR TO ANY MAINTENANCE OPERATION !!
The TT Range has been designed with ease of use in mind, this included easy stripping-
down and cleaning. After use, empty
waste-water tank using emptying hose and ush out with clean-water (Fig.20).
20
Andere Handbücher für HT4045
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Numatic Schrubber Handbücher
Numatic
Numatic TRG 720/200T Bedienungsanleitung
Numatic
Numatic TTB 6055 Bedienungsanleitung
Numatic
Numatic TTV 5565 Bedienungsanleitung
Numatic
Numatic TTV 5565 Bedienungsanleitung
Numatic
Numatic TGB1620T Bedienungsanleitung
Numatic
Numatic TTB 4045/100 Bedienungsanleitung
Numatic
Numatic TTB1840NX Bedienungsanleitung
Numatic
Numatic TGB 8572/200T Bedienungsanleitung
Numatic
Numatic TTV 678G / 300T Bedienungsanleitung
Numatic
Numatic NX300 Bedienungsanleitung
Numatic
Numatic TTB 1840G Bedienungsanleitung
Numatic
Numatic NX300 Bedienungsanleitung
Numatic
Numatic TGB2120 Bedienungsanleitung
Numatic
Numatic TRG 720/200T Bedienungsanleitung
Numatic
Numatic TT 6650S Bedienungsanleitung
Numatic
Numatic TTB6055/100 Bedienungsanleitung
Numatic
Numatic TRO 650G Bedienungsanleitung
Numatic
Numatic TT 1840 Bedienungsanleitung
Numatic
Numatic TTV 678 Bedienungsanleitung
Numatic
Numatic TRO 650/200T Bedienungsanleitung
Beliebte Schrubber Handbücher anderer Marken
U.S. Products
U.S. Products PEX 500-C-TICK Betriebsanleitung
Mclennan
Mclennan C510 Bedienungsanleitung
Tennant
Tennant T20 LPG Bedienungsanleitung
Columbus
Columbus ARA 66 BM 100 Bedienungsanleitung
American-Lincoln
American-Lincoln 505-945 Bedienungsanleitung
FIORENTINI
FIORENTINI ET 65-75 Bedienungsanleitung
