Numatic TGB 516 36V Bedienungsanleitung

Caution! Read instructions before using the machine

Original Instructions

TGB 516 36V

SCRUBBER DRYER

www.numatic.co.uk

1www.numatic.co.uk

Machine Overview ................................. Page 2

Control Panel Overview ................................. Page 3

Quick Set up Guide ................................. Page 4

Machine Set up Guide ................................. Page 5-6

Fitting the Brush / Pad ................................. Page 5

Fitting the Floor-tool ................................. Page 5

Filling the Clean Water Tank ........................... Page 6

Fill Level Indicator ............................... Page 6

Water Flow Adjustment .................................Page 6

Setting the Cleaning Controls ..................... Page 7

System Error Indicators ................................. Page 7

Machine Operation ................................. Page 8

Raising/Lowering Floor-tool.............................. Page 8

Emptying Top/Bottom Tanks ............................ Page 8

Machine in Use ................................. Page 8

Regular Maintenance ................................. Page 9-10

Emptying Top/Bottom Tank............................... Page 9

Separator ................................. Page 9

Changing Floor-tool Blades ............................. Page 10

Retting the Floor-tool Blades ......................... Page 10

Lifting the Machine ................................. Page 11

Specications ................................. Page 12

Trouble Shooting ................................. Page 12

About the Machine ................................. Page 13

Rating Label / PPE /

Recycling ................................. Page 13

Information for Scrubber Dryer .................... Page 14

Twintec Maintenance ................................. Page 15

Spare Parts ................................. Page 15

Recommended Spare Parts ............................. Page 15

Schematic Diagram ................................. Page 15

EU Declaration Document ........................... Page 16

Warranty ................................. Page 17

Company Address ................................. Page 19

SCRUBBER DRYER

Index

After the removal of all the packaging,

carefully open and check the contents

• Owner Manual

• Battery & Charger Manual

• Battery Charger & Lead

• Battery •Scrub Brush

• Squeegee Assembly

PLEASE READ

BEFORE COMMENCING

OPERATION

1Operator control panel ( see page 3 )

2Triggers

3Waste-water tank

4Clean-water tank

5Brush deck

6Squeegee blades

7Floor-tool retaining knobs

8Clean-water On / O󰀨 tap

9Clean-water emptying cap

10 Floor-tool vacuum hose

11 Vacuum hose

12 Separator

13 Clean-water ller cap

14 Clean-water level indicator

15 Clean-water tank ll point

16 Start Switch

17 Top tank (waste water) drainage hose

18 Battery compartment

19 Battery

20 Battery charger

TTB 1840 36V

T 01460 68600

Machine Overview

3www.numatic.co.uk

SCRUBBER DRYER

1Battery Charge Level Display

2Water Flow On / O󰀨 Button

3Water Flow Indicator

4Vacuum O󰀨/On Indicator

5Vacuum O󰀨/On Button

6Handle Position Lever

7Start Switch

8Triggers

Control Panel Overview

In the event of a breakdown contact

your Numatic dealer or the

Numatic Technical

help line +44 (0)1460 269268

TTB 1840 36V

T 01460 68600

Quick Set-up Guide

TTB 1840 36V CONTENTS

●Owner Manual

●Battery & Charger Manual

●Battery Charger & Lead

●Battery●Scrub Brush

●Squeegee Assembly

Using the handle position lever, (Fig.1) Move the handle into the upright position,

(Fig.2)

Slide the brush / pad under the brush

deck (Fig.3).

Fit the brush / pad onto the Nulock drive

chuck, twist to lock the brush / pad in

place (Fig.4).

Swing the oor-tool carrier from behind

the brush. Using the two locking knobs

tted to the oor-tool, secure the

oor-tool to the oor-tool carrier (Fig.5).

Fill the clear-water tank to Max of 18 litresSlide the battery into the

battery compartment (Fig.6)

Close the exible lid making sure it is

sealed correctly. (Fig.7)

PLEASE READ BEFORE COMMENCINGANY OPERATION.AFTER THE REMOVALOFALL

THE PACKAGING, CAREFULLY OPEN AND CHECK THE CONTENTS. !!

ALWAYS ENSURE THAT THE FLOOR IS PRE-SWEPT

AND RELEVANT SAFETY SIGNS ARE DISPLAYED.

! !

5www.numatic.co.uk

Swing the oor-tool carrier to the

side of the machine. (Fig.1).

Secure to the carrier using the two

knobs tted to the oor-tool carrier

(Fig.2) - (Fig.3).

Do not over tighten the retaining

knobs.

Ensure inspection cap is in place on

the uid pipe. (Fig.4) - (Fig.5)

For tting the oor-tool blades

(See Page 10).

Machine Set-up Guide

ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF

BEFORE MAKING ANY ADJUSTMENTS !!

400mm Brush / 360mm Pad.

Featuring the Nulock brush system.

The brush is simply pushed and twisted to lock, making tting and removal a simple process.

Slide the brush / pad under the brush deck.

Fit the brush / pad onto the Nulock drive chuck, twist to lock the brush / pad in place.

Safety gloves are recommended for the changing of used brushes.

Turn on the clean water tap.

Fitting the Brush / Pad / Turn on water

Fitting the Floor-tool

The oor-tool has been designed for quick tting, allowing easy squeegee blade replacement and a safety knock-o󰀨 feature if the

oor-tool gets snagged, whilst in transit.

NOTE:Itiseasiertottheoor-tooliftheweightofthemachineisrestingonthebrush.Ensurethebrushisttedrst.

T 01460 68600

Machine Set-up Guide

NOTE: Great care must be taken to ensure that contaminants (leaves, hair, dirt, etc.) are not allowed to enter the clean

watertankduringthellingprocess.Ifusingasuitablecontainer,ensureitisalwayscleanandfreefromdebris.

The TTB 1840 is equipped with a large 18 litre clean-water tank allowing large areas to be cleaned in a single ll.

Filling the Clean Water Tank

Fill Level Indicator

Water Flow Adjustment

To ll the clean-water tank, remove the ller cap (Fig.1). Fill using a hose or a suitable container (Fig.2).

Use the ll indicator (Fig.3).

Fill Indicator

Showing the clean-water tank full

(Fig.B)

Showing the clean-water tank empty

(Fig.A)

Located on the left of the machine is the On / O󰀨 water tap (Fig.1).

Set the tap to enable the cleaning solution .(Fig.2).

7www.numatic.co.uk

In the event of a fault the battery lights (F) will ash and the

unit will stop operating.

The lights will ash a number of times then pause.

The number of ashes can be used to identify the fault.

1) Battery Low

2) Battery over temperature

3) Battery communications error

4) Control board over temperature

5) System power exceeded

6) Vacuum overload

7) Brush overload

8) Control board failed

Setting the Cleaning Controls

System Error Indicators

To start the brush with the congured water and vacuum

settings pull either trigger and press the Start switch (A).

Note: that the start switch (A) must be pressed after the

trigger is pulled.

The running state of the vacuum and water can be adjusted

with or without the brush running. First pull one of the triggers

then press the vacuum and water buttons to set the desired

operation .These states will be stored for use when the

machine is restarted.

When the Triggers are released the brush motor and the

cleaning solution pump will switch o󰀨, the vacuum motor will

continue for 10 seconds.

To Enable /Disable Vacuum press button (D).

Note: that the vacuum can only be stopped by pressing the

vacuum button (D) pulling the triggers will have no e󰀨ect.

The panel if unused, will automatically turn o󰀨 after 60

seconds.

IMPORTANT

If the brush motor keeps overloading consider using a dierent type of brush.

Heavy brush load decreases the available battery run time. !!

To check the battery level pull one of the Triggers or press button (A).

Trigger Trigger

On / O󰀨

Releasing the handle triggers will allow the machine to reset.

T 01460 68600

To raise the oor-tool, ensure the oor-tool carrier is central to the machine.

Lift the lever near the base of the handle and lock into position.

Raising/Lowering the Floor-tool

Machine Operation

WHEN HANDLING CHEMICALS

Always ensure that chemical manufacturer’s safety guidelines are followed.

Only use chemicals recommended for use in auto scrubber-dryers. !!

IMPORTANT

Do not operate machine unless the Operator Manual has been read

and fully understood. !!

To operate, set water ow rate tap, lower the oor-tool, press the vacuum / water switches, pull

trigger(s).

The waste water is then retrieved by the suction oor-tool.

Overlap each scrubbing path by 10cm to ensure an even clean.

Do not operate the machine on slopes that exceed (2%),when full.

On heavily soiled oors use a ‘double scrub’ technique.

First pre-scrub the oor with the oor-tool in the raised position,

allow the chemical time to work then scrub the area a second

time with the oor-tool lowered.

If streaking occurs wipe oor-tool blades clean.

NOTE: Care must be taken to reduce speed when

cornering or when manoeuvring around obstacles

Machine In Use

9www.numatic.co.uk

Regular Maintenance

Remove the two hoses to disconnect the separator from the

machine (1 & 2).

Remove xing band holding separator in place (3).

Lift o󰀨 the separator. The separator has a sealing-rubber which

should be examined at every clean-down (4).

Rinse using clean water.

ALWAYS ENSURE THAT THE BATTERY IS REMOVED

PRIOR TO ANY MAINTENANCE OPERATION !!

After use, empty waste-water tank using

emptying hose and ush-out with clean

water. (g.A).

The clean-water tank can be drained via

the red cap tted to the left hand side

of the machine. There is a sealing bung

beneath the red cap (ensure the sealing

bung is clean) The cap should only be

done up by hand. (g.B).

Emptying Top Tank

Separator

Emptying Bottom Tank

Remove the lter and basket clipped into the separator and ush with clean water (5 & 6).

Replace the lter by rst tting the rear of the lter rst then clipping in the front to lock in place (5).

Inhaltsverzeichnis

Andere Numatic Schrubber Handbücher

Numatic

Numatic TTB 1840 36V Bedienungsanleitung

Numatic

Numatic TRO 650/200T Bedienungsanleitung

Numatic

Numatic TT 6650S Bedienungsanleitung

Numatic

Numatic TT-3450S Leitfaden

Numatic

Numatic NX300 Bedienungsanleitung

Numatic

Numatic TTB 4045/100 Bedienungsanleitung

Numatic

Numatic NUC244NX Bedienungsanleitung

Numatic

Numatic NUC244NX Bedienungsanleitung

Numatic

Numatic NX1K TBL4045 Bedienungsanleitung

Numatic

Numatic TTB6055/100 Bedienungsanleitung

Numatic

Numatic NTT 2003 Bedienungsanleitung

Numatic

Numatic NACECARE NX300 TTB3045NX Bedienungsanleitung

Numatic

Numatic TTV - 4555/100T Bedienungsanleitung

Numatic

Numatic TTV 678G/300T Bedienungsanleitung

Numatic

Numatic TT 516 Bedienungsanleitung

Numatic

Numatic TTB-4500/100S Leitfaden

Numatic

Numatic TTV 678G / 300T Bedienungsanleitung

Numatic

Numatic TTV 5565 Bedienungsanleitung

Numatic

Numatic TTV - 4555/100T Bedienungsanleitung

Numatic

Numatic TTV678G/400T Bedienungsanleitung

Numatic

Numatic TT6650G Bedienungsanleitung

Numatic

Numatic NX300 Bedienungsanleitung

Numatic

Numatic HT4045 Bedienungsanleitung

Numatic

Numatic TGB 6055 Bedienungsanleitung

Beliebte Schrubber Handbücher anderer Marken

Olympus

Olympus M200H Bedienungsanleitung

Clarke

Clarke BEXT 100H Installations- und Betriebsanleitung

JOHNY VAC

JOHNY VAC JVC70BCT Bedienungsanleitung

RCm

RCm Elan Series Handbuch

Kärcher

Kärcher B 120 W Bedienungsanleitung

Truvox

Truvox Orbis MotorScrubber 20 Bedienungsanleitung

U.S. Products

U.S. Products PEX 500-C-TICK Betriebsanleitung

Mclennan

Mclennan C510 Bedienungsanleitung

Tennant

Tennant T20 LPG Bedienungsanleitung

Columbus

Columbus ARA 66 BM 100 Bedienungsanleitung

American-Lincoln

American-Lincoln 505-945 Bedienungsanleitung

FIORENTINI

FIORENTINI ET 65-75 Bedienungsanleitung

Floorpul

Floorpul ruby 48 blt Benutzerhandbuch

Onyx

Onyx RX-34 Bedienungsanleitung

Dustbane

Dustbane Hurricane 400 Bedienungsanleitung

Sana

Sana EUJ-702 Bedienungsanleitung

REMS

REMS Twist Bedienungsanleitung

Tennant

Tennant 7200 Bedienungsanleitung