Numatic NX300 Bedienungsanleitung

TTB 3045NX 36V

SCRUBBER DRYER

numatic.com

CAUTION, Read instructions before using the machine

Original Instructions

2www.numatic.co.uk

Machine Overview .................................Pages 2-3

Control Panel Overview .................................Page 4

Machine Set up Guide .................................Page 5

Fitting the Brush / Pad......................................Page 5

Fitting the Floor Tool .................................Page 5

Fitting the Hose Guide .................................Page 6

Filling the Clean Water Tank.............................Page 6

Handle Height Adjustment ..............................Page 7

Fitting the Batteries...........................................Page 7

Lowering the Floor Tool .................................Page 8

Raise / Lower Brush Deck................................Page 8

Setting the Cleaning Controls .........................Page 8-9

System error indicators .................................. Page 9

Brush Pressure / Load Adjustment.................. Page 9-10

Breakaway Floor Tool .................................Page 10

Machine in Use .................................Page 11

Machine Maintenance .................................Page 11

Changing Floor tool Blades ..............................Page 12

Rating Label / Personal Protective Equipment /

Recycling .................................Page 13

Safety Precautions .................................Page 14

Schematic Diagram .................................Page 15

Recommended Spare Parts ...........................Page 15

Trouble Shooting .................................Page 15

Battery Information....................... ....................Page 16-19

 .................................Page 19

EU Declaration Document ..............................Page 17

Warranty .................................Page 23

Company Address .................................Page 24

SCRUBBER DRYER

Index

After the removal of all the packaging,

carefully open and check the contents

Owner Manual











PLEASE READ

BEFORE COMMENCING

OPERATION

TTB 3045NX 36V

Deck Pressure Weights

Location

2 Top Tank (Waste Water)

3 Bottom Tank (Clean Water)

4 Brush Deck

5 Clean Water Tank Filter

6 Rear Wheels

7󰀨

8 Separator

9 Clean-Water Emptying Hose

10 Top Tank (Waste-Water) Drainage Hose

11 Clean-Water Filler Cap and Hose

12 Floor Tool Vacuum Hose

13 Vacuum Hose

14 Battery Compartment

15 Floor-Tool Lifting Lever

16 Control Panel

17 Clean Water Level Indicator / Drainage Hose

18 Floor-Tool Retaining Knobs

19 Floor Tool

20 Deck Locking Mechanism

Deck Pressure Weights

22 Dual Charger + Batteries

T 01460 68600

TTB 3045NX 36V

Machine Overview

4www.numatic.co.uk

SCRUBBER DRYER

1Battery Charge Level Display

2󰀨

3Water Flow Indicator

4󰀨

5󰀨

6Handle Position Lever

7Start Switch

8Triggers

Control Panel Overview

In the event of a breakdown contact

your Numatic dealer or the

Numatic Technical

help line +44 (0)1460 269268

TTB 3045NX 36V

T 01460 68600



detent pins.

Push waste collection pipe onto the





lower for cleaning operation using



of the machine.



(See Page 12).

Machine Set-up Guide

ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF

BEFORE MAKING ANY ADJUSTMENTS !!

450mm Brush or 400mm Pad.

Featuring the Nulock brush system.



Slide the brush / pad under the brush deck.

Fit the brush / pad onto the Nulock drive chuck, twist to lock the brush / pad in place.

Safety gloves are recommended for the changing of used brushes.

Turn on the clean water tap.

Fitting the Brush / Pad / Turn on water

Fitting the Floor Tool

󰀨



Note: It is easier to t the oor tool if the weight of the machine is resting on the brush. Ensure the brush is tted rst.

6www.numatic.co.uk

The vacuum hose has a U-bend clip which creates a U-bend in the hose preventing water spillage when the vacuum is switched

󰀨

Fitting the Hose Guide

Note: DO NOT push the vacuum hose

onto the oor tool with the oor tool in

the raised position.

Machine Set-up Guide





Note: Great care must be taken to ensure that contaminants (leaves, hair, dirt,

etc.) are not allowed to enter the clean water tank during the lling process. If

using a bucket or similar, ensure it is always clean and free from debris.

Filling the Clean Water Tank







Fill the clean-water tank to MAX line indication on tank, including cleaning chemicals if

required. Follow chemical manufacturing guide lines.

The clear dump hose at the rear of the machine can be used to see the level of the

clean-water. (Fig.D).

Control of Substances Hazardous to Health (COSHH)

For best results use a non-foaming type of chemical recommended for use in auto



hazardous substances refer to health and safety instructions online.

WHEN HANDLING AND MIXING CHEMICALS

Always ensure that chemical manufacturer’s safety guidelines are followed.

Only use chemicals recommended for use in auto scrubber-dryers. !!

T 01460 68600

Using the handle position lever, lower the handle to a comfortable working position.

Machine Set-up Guide

Handle Height Adjustment

The machine is now ready to be moved to

the cleaning site.

Before performing the cleaning operation,

place out appropriate warning signs and



IMPORTANT

Do not operate machine unless the Operator Manual has been read and fully understood. !!

Fitting the Batteries

Open the battery door (A).

Make sure Battery locks are open (B) and

insert both fully charged batteries (C).

Secure the batteries into the machine

using the battery locks (D) before closing

the battery door

Note: it is important to make sure

battery locks are fully engaged before

operating or moving your TTB.3045.NX

Fitting and Locking the

Batteries

8www.numatic.co.uk

To tip the deck into the down position (Operating mode). Press in the brush deck locking pin (Fig.A)



(Transit mode) simply lift the deck and the spring loaded locking pin will activate to hold the deck up.



section), we are now ready to set the

controls to suit the cleaning conditions.

Before any settings can be applied,

ensure the brush deck is lowered.



lower position.

Note: Do not pull the machine

backwards with the oor tool in the

lowered position, this could possibly

damage the blades.

Raising/Lowering

the Floor Tool

Machine Operation

Raising/Lowering the Brush Deck

Setting the Cleaning Controls

To check the battery level pull one of the Triggers

or press button (A).

Trigger Trigger

󰀨



T 01460 68600



unit will stop operating.





System Error Indicators



settings pull either trigger and press the Start switch (A).

The running state of the vacuum (D) and water (C) can be

adjusted whilst the brushes are running.

To cancel vac overrun press any switch (vac/water/handle/start)

IMPORTANT

If the brush motor keeps overloading consider using a dierent type of brush.

Heavy brush load decreases the available battery run time. !!

*Releasing the handle triggers, or remove the batteries will allow the machine to reset.

Number of Flashes Priority Description Solution

1 Low Low Battery Replace, Charge Batteries

2 Low Start sequence error, both trigger and handle must be

active within 2 seconds of each

other. If one is held for longer while the

machine is idle the unit will enter this error state

*Reset Machine

4 High Battery over temp *Reset Machine

5 High Battery communications fail *Reset Machine

6 High Battery over current *Reset Machine

7 High Control board over temp *Reset Machine

8 High Vacuum over current *Reset Machine

9 High Brush over current *Reset Machine

10 High Control board failure Renew (contact service dept)

The errors are split into two groups, low and high priority. Low priority errors are to be expected in normal operation and are





In normal operation the battery display will show the state of charge of the battery with the least charge, there is no indication which

battery this is.

The error display can indicate battery related errors, there is no indication which battery has the fault.

10 www.numatic.co.uk

TTB.3045.NX comes with one11kg weight (3). Place the Deck Pressure Weight into the machine before using (4).

󰀩TTB.3045.NX has been designed to use extra

weight if needed (available as an optional extra).

Machine Operation



Allowing it to safely disengage from its mounting should it become caught on an obstruction, during forward machine movement.





Break-away Floor Tool

Brush Pressure / Load Adjustment

NOTE* Additional weight will decrease run time. The TTB.3045.NX has been designed to have no more then a Maximum of two weights.

Brush (gCM2) Pad (gCM2)

Pressure 1 (Light) 1 x 11kg in weight location B 24.52 25.28

Pressure 2 (Medium) 1 x 11kg in weight location A 29.14 30.05

* Additional 11kg weight available as an optional extra.

Pressure 3 (Heavy) 2 x 11kg weights one location A and one in location B 31.63 32.61

Pressure 4 (Extra Heavy) 2 x 11kg weights in position A (Stacked) 35.54 36.64

Remove the Top (Waste Water) tank (1). Set

in the lower tank are location pillars (2) to

locate the Deck Pressure Weights (5).

To obtain the best out of your TTB.3045.NX

Numatic have supplied a ‘Deck

Pressure Weight’ allowing the operator to

add or remove pressure on the brush or pad



Using the Deck Pressure

Weights.

Andere Handbücher für NX300

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Numatic Schrubber Handbücher

Numatic

Numatic TTV 678G / 300T Bedienungsanleitung

Numatic

Numatic TGB 516 Bedienungsanleitung

Numatic

Numatic TRG 720/200T Bedienungsanleitung

Numatic

Numatic TRO 650G Bedienungsanleitung

Numatic

Numatic TT 516 Bedienungsanleitung

Numatic

Numatic TT-3450S Leitfaden

Numatic

Numatic NX 1K Bedienungsanleitung

Numatic

Numatic TTB 1840 Bedienungsanleitung

Numatic

Numatic TT-4550S Leitfaden

Numatic

Numatic CRO 8055 Bedienungsanleitung

Numatic

Numatic TGB 516 36V Bedienungsanleitung

Numatic

Numatic NX300 Bedienungsanleitung

Numatic

Numatic TT 1840 Bedienungsanleitung

Numatic

Numatic HTB 1840 Bedienungsanleitung

Numatic

Numatic TGB 8572/200T Bedienungsanleitung

Numatic

Numatic TTV 678G/300T Bedienungsanleitung

Numatic

Numatic CRO 8072 Bedienungsanleitung

Numatic

Numatic TGB2120 Bedienungsanleitung

Numatic

Numatic TTB 6055/100T Bedienungsanleitung

Numatic

Numatic TTB 1840 36V Bedienungsanleitung

Numatic

Numatic TTV 5565 Bedienungsanleitung

Numatic

Numatic CRO 8055/100T Bedienungsanleitung

Numatic

Numatic TT6650G Bedienungsanleitung

Numatic

Numatic NX300 Bedienungsanleitung

Beliebte Schrubber Handbücher anderer Marken

Olympus

Olympus M200H Bedienungsanleitung

Clarke

Clarke BEXT 100H Installations- und Betriebsanleitung

JOHNY VAC

JOHNY VAC JVC70BCT Bedienungsanleitung

RCm

RCm Elan Series Handbuch

Kärcher

Kärcher B 120 W Bedienungsanleitung

Truvox

Truvox Orbis MotorScrubber 20 Bedienungsanleitung

U.S. Products

U.S. Products PEX 500-C-TICK Betriebsanleitung

Mclennan

Mclennan C510 Bedienungsanleitung

Tennant

Tennant T20 LPG Bedienungsanleitung

Columbus

Columbus ARA 66 BM 100 Bedienungsanleitung

American-Lincoln

American-Lincoln 505-945 Bedienungsanleitung

FIORENTINI

FIORENTINI ET 65-75 Bedienungsanleitung

Floorpul

Floorpul ruby 48 blt Benutzerhandbuch

Onyx

Onyx RX-34 Bedienungsanleitung

Dustbane

Dustbane Hurricane 400 Bedienungsanleitung

Sana

Sana EUJ-702 Bedienungsanleitung

REMS

REMS Twist Bedienungsanleitung

Tennant

Tennant 7200 Bedienungsanleitung