Numatic TTB1840NX Bedienungsanleitung
1
Caution! Read instructions before using the machine
Original Instructions
TTB 1840 36V
SCRUBBER DRYER
numatic.com
GB
2www.numatic.co.uk
Machine Overview ................................. Page 2
Control Panel Overview ................................. Page 3
Quick Set up Guide ................................. Page 4
Machine Set up Guide ................................. Page 5-6
Fitting the Brush / Pad ................................. Page 5
Fitting the Floor-tool ................................. Page 5
Filling the Clean Water Tank ........................... Page 6
Fill Level Indicator ............................... Page 6
Water Flow Adjustment .................................Page 6
Setting the Cleaning Controls ..................... Page 7
System Error Indicators ................................. Page 7
Machine Operation ................................. Page 8
Raising/Lowering Floor-tool.............................. Page 8
Emptying Top/Bottom Tanks ............................ Page 8
Machine in Use ................................. Page 8
Regular Maintenance ................................. Page 9-10
Emptying Top/Bottom Tank............................... Page 9
Separator ................................. Page 9
Changing Floor-tool Blades ............................. Page 10
Retting the Floor-tool Blades ......................... Page 10
Lifting the Machine ................................. Page 11
Specications ................................. Page 12
Trouble Shooting ................................. Page 12
About the Machine ................................. Page 13
Rating Label / PPE /
Recycling ................................. Page 13
Information for Scrubber Dryer .................... Page 14
Twintec Maintenance ................................. Page 15
Spare Parts ................................. Page 15
Recommended Spare Parts ............................. Page 15
Schematic Diagram ................................. Page 15
EU Declaration Document ........................... Page 16
Warranty ................................. Page 17
Company Address ................................. Page 19
SCRUBBER DRYER
Index
After the removal of all the packaging,
carefully open and check the contents
• Owner Manual
• Battery & Charger Manual
• Battery Charger & Lead
• Battery •Scrub Brush
• Squeegee Assembly
PLEASE READ
BEFORE COMMENCING
OPERATION
1Operator control panel ( see page 3 )
2Triggers
3Waste-water tank
4Clean-water tank
5Brush deck
6Squeegee blades
7Floor-tool retaining knobs
8Clean-water On / O tap
9Clean-water emptying cap
10 Floor-tool vacuum hose
11 Vacuum hose
12 Separator
13 Clean-water ller cap
14 Clean-water level indicator
15 Clean-water tank ll point
16 Start Switch
17 Top tank (waste water) drainage hose
18 Battery compartment
19 Battery
20 Battery charger
TTB 1840 36V
3
T 01460 68600
Machine Overview
1
6
4
2
3
9
8
7
5
13
14
15
16
12
18
19
20
17
11
10
4www.numatic.co.uk
SCRUBBER DRYER
1Battery Charge Level Display
2Water Flow On / O Button
3Water Flow Indicator
4Vacuum O/On Indicator
5Vacuum O/On Button
6Handle Position Lever
7Start Switch
8Triggers
Control Panel Overview
In the event of a breakdown contact
your Numatic dealer or the
Numatic Technical
help line +44 (0)1460 269268
1
4
3
5
8
8
6
7
2
TTB 1840 36V
5
T 01460 68600
Quick Set-up Guide
TTB 1840 36V CONTENTS
●Owner Manual
●Battery & Charger Manual
●Battery Charger & Lead
●Battery●Scrub Brush
●Squeegee Assembly
Using the handle position lever, (Fig.1) Move the handle into the upright position,
(Fig.2)
Slide the brush / pad under the brush
deck (Fig.3).
Fit the brush / pad onto the Nulock drive
chuck, twist to lock the brush / pad in
place (Fig.4).
Swing the oor-tool carrier from behind
the brush. Using the two locking knobs
tted to the oor-tool, secure the
oor-tool to the oor-tool carrier (Fig.5).
Fill the clear-water tank to Max of 18 litresSlide the battery into the
battery compartment (Fig.6)
Close the exible lid making sure it is
sealed correctly. (Fig.7)
PLEASE READ BEFORE COMMENCINGANY OPERATION.AFTER THE REMOVAL OFALL
THE PACKAGING, CAREFULLY OPEN AND CHECK THE CONTENTS. !!
3
6
8
7
1
4
2
5
ALWAYS ENSURE THAT THE FLOOR IS PRE-SWEPT
AND RELEVANT SAFETY SIGNS ARE DISPLAYED.
! !
6www.numatic.co.uk
Swing the oor-tool carrier to the
side of the machine. (Fig.1).
Secure to the carrier using the two
knobs tted to the oor-tool carrier
(Fig.2) - (Fig.3).
Do not over tighten the retaining
knobs.
Ensure inspection cap is in place on
the uid pipe. (Fig.4) - (Fig.5)
For tting the oor-tool blades
(See Page 10).
Machine Set-up Guide
ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF
BEFORE MAKING ANY ADJUSTMENTS !!
400mm Brush / 360mm Pad.
Featuring the Nulock brush system.
The brush is simply pushed and twisted to lock, making tting and removal a simple process.
Slide the brush / pad under the brush deck.
Fit the brush / pad onto the Nulock drive chuck, twist to lock the brush / pad in place.
Safety gloves are recommended for the changing of used brushes.
Turn on the clean water tap.
Fitting the Brush / Pad / Turn on water
Fitting the Floor-tool
The oor-tool has been designed for quick tting, allowing easy squeegee blade replacement and a safety knock-o feature if the
oor-tool gets snagged, whilst in transit.
NOTE:Itiseasiertottheoor-tooliftheweightofthemachineisrestingonthebrush.Ensurethebrushisttedrst.
1
2
3
4
5
7
T 01460 68600
Machine Set-up Guide
NOTE: Great care must be taken to ensure that contaminants (leaves, hair, dirt, etc.) are not allowed to enter the clean
watertankduringthellingprocess.Ifusingasuitablecontainer,ensureitisalwayscleanandfreefromdebris.
The TTB 1840 is equipped with a large 18 litre clean-water tank allowing large areas to be cleaned in a single ll.
Filling the Clean Water Tank
Fill Level Indicator
Water Flow Adjustment
To ll the clean-water tank, remove the ller cap (Fig.1). Fill using a hose or a suitable container (Fig.2).
Use the ll indicator (Fig.3).
1
2
3
Fill Indicator
A
1
2
B
Showing the clean-water tank full
(Fig.B)
Showing the clean-water tank empty
(Fig.A)
Located on the left of the machine is the On / O water tap (Fig.1).
Set the tap to enable the cleaning solution .(Fig.2).
8www.numatic.co.uk
In the event of a fault the battery lights (F) will ash and the
unit will stop operating.
The lights will ash a number of times then pause.
The number of ashes can be used to identify the fault.
1) Battery Low
2) Battery over temperature
3) Battery communications error
4) Control board over temperature
5) System power exceeded
6) Vacuum overload
7) Brush overload
8) Control board failed
Setting the Cleaning Controls
System Error Indicators
To start the brush with the congured water and vacuum
settings pull either trigger and press the Start switch (A).
Note: that the start switch (A) must be pressed after the
trigger is pulled.
The running state of the vacuum and water can be adjusted
with or without the brush running. First pull one of the triggers
then press the vacuum and water buttons to set the desired
operation .These states will be stored for use when the
machine is restarted.
When the Triggers are released the brush motor and the
cleaning solution pump will switch o, the vacuum motor will
continue for 10 seconds.
To Enable /Disable Vacuum press button (D).
Note: that the vacuum can only be stopped by pressing the
vacuum button (D) pulling the triggers will have no eect.
The panel if unused, will automatically turn o after 60
seconds.
IMPORTANT
If the brush motor keeps overloading consider using a dierent type of brush.
Heavy brush load decreases the available battery run time. !!
To check the battery level pull one of the Triggers or press button (A).
A
C
D
F
B
Trigger Trigger
On / O
Releasing the handle triggers will allow the machine to reset.
9
T 01460 68600
To raise the oor-tool, ensure the oor-tool carrier is central to the machine.
Lift the lever near the base of the handle and lock into position.
Raising/Lowering the Floor-tool
Machine Operation
WHEN HANDLING CHEMICALS
Always ensure that chemical manufacturer’s safety guidelines are followed.
Only use chemicals recommended for use in auto scrubber-dryers. !!
IMPORTANT
Do not operate machine unless the Operator Manual has been read
and fully understood. !!
To operate, set water ow rate tap, lower the oor-tool, press the vacuum / water switches, pull
trigger(s).
The waste water is then retrieved by the suction oor-tool.
Overlap each scrubbing path by 10cm to ensure an even clean.
Do not operate the machine on slopes that exceed (2%),when full.
On heavily soiled oors use a ‘double scrub’ technique.
First pre-scrub the oor with the oor-tool in the raised position,
allow the chemical time to work then scrub the area a second
time with the oor-tool lowered.
If streaking occurs wipe oor-tool blades clean.
NOTE: Care must be taken to reduce speed when
cornering or when manoeuvring around obstacles
Machine In Use
10 www.numatic.co.uk
Regular Maintenance
Remove the two hoses to disconnect the separator from the
machine (1 & 2).
Remove xing band holding separator in place (3).
Lift o the separator. The separator has a sealing-rubber which
should be examined at every clean-down (4).
Rinse using clean water.
ALWAYS ENSURE THAT THE BATTERY IS REMOVED
PRIOR TO ANY MAINTENANCE OPERATION !!
After use, empty waste-water tank using
emptying hose and ush-out with clean
water. (g.A).
The clean-water tank can be drained via
the red cap tted to the left hand side
of the machine. There is a sealing bung
beneath the red cap (ensure the sealing
bung is clean) The cap should only be
done up by hand. (g.B).
Emptying Top Tank
Separator
Emptying Bottom Tank
A
1
2
3
6
5
4
B
Remove the lter and basket clipped into the separator and ush with clean water (5 & 6).
Replace the lter by rst tting the rear of the lter rst then clipping in the front to lock in place (5).
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Numatic Schrubber Handbücher
Numatic
Numatic TTB 4045/100 Bedienungsanleitung
Numatic
Numatic TGB 6055 Bedienungsanleitung
Numatic
Numatic TTB 4045/100 Bedienungsanleitung
Numatic
Numatic NUC244NX Bedienungsanleitung
Numatic
Numatic HGB 3045/55 Bedienungsanleitung
Numatic
Numatic HT4045 Bedienungsanleitung
Numatic
Numatic TT 1535G Bedienungsanleitung
Numatic
Numatic HTB 1840 Bedienungsanleitung
Numatic
Numatic NX1K TBL4045 Bedienungsanleitung
Numatic
Numatic TTV 678 Bedienungsanleitung
Numatic
Numatic TTV 678G/300T Bedienungsanleitung
Numatic
Numatic TTV 5565 Bedienungsanleitung
Numatic
Numatic TGB1620T Bedienungsanleitung
Numatic
Numatic TTB 1840 Bedienungsanleitung
Numatic
Numatic NX300 Bedienungsanleitung
Numatic
Numatic HGB 3045 Bedienungsanleitung
Numatic
Numatic CRO 8055/100T Bedienungsanleitung
Numatic
Numatic TRO 650G Bedienungsanleitung
Numatic
Numatic TGB 8572/200T Bedienungsanleitung
Numatic
Numatic TTB 6055/100T Bedienungsanleitung
Beliebte Schrubber Handbücher anderer Marken
U.S. Products
U.S. Products PEX 500-C-TICK Betriebsanleitung
Mclennan
Mclennan C510 Bedienungsanleitung
Tennant
Tennant T20 LPG Bedienungsanleitung
Columbus
Columbus ARA 66 BM 100 Bedienungsanleitung
American-Lincoln
American-Lincoln 505-945 Bedienungsanleitung
FIORENTINI
FIORENTINI ET 65-75 Bedienungsanleitung
