Nvidia SN2700 Bedienungsanleitung

Installation
System Installation and Initialization
Installation and initialization of the system require attention to the normal mechanical, power, and thermal precautions for rack-mounted equipment.
The installation procedure for the system involves the following phases:
Step Procedure See
1 Follow the safety warnings Safety Warnings
2 Pay attention to the air flow consideration within the system and rack Air Flow
3 Make sure that none of the package contents is missing or damaged Package Contents
4 Mount the system into a rack enclosure 19" System Mounting Options
5 Power on the system Initial Power On
6 Perform system bring-up System Bring-Up
7 [Optional] FRU replacements FRU Replacements
Safety Warnings
Prior to the installation, please review the safety warnings. Note that not all warnings may apply to all models.
Safety Warnings (English)
Installation Instructions
Read all installation instructions before connecting the equipment to the power source.
Bodily Injury Due to Weight
Use enough people to safely lift this product. 
Heavy Equipment
This equipment is heavy and should be moved using a mechanical lift to avoid injuries.
The rack mounting holes conform to the EIA-310 standard for 19-inch racks. Take precautions to guarantee proper ventilation in order to 
maintain good airflow at ambient temperature.
Unless otherwise specified, NVIDIA products are designed to work in an environmentally controlled data center with low levels of gaseous and 
dust (particulate) contamination.
The operation environment should meet severity level G1 as per ISA 71.04 for gaseous contamination and ISO 14644-1 class 8 for cleanliness 
level.
Safety warnings are provided here in the English language. For safety warnings in other languages, refer to the 1U Switch Installation Safety 
 document available on mellanox.com.Instructions

Risk of Electric Shock!

With the fan module removed power pins are accessible within the module cavity.

Do not insert tools or body parts into the fan module cavity.

For AC powered switch systems: Disconnecting one power supply only disconnects one module. To isolate the unit completely, all connected

power supplies must be disconnected.

Over-temperature

This equipment should not be operated in an area with an ambient temperature exceeding the maximum recommended: 45°C (113°F). Moreover, to

guarantee proper ventilation, allow at least 8 cm (3 inches) of clearance around the ventilation openings.

Stacking the Chassis

The chassis should not be stacked on any other equipment. If the chassis falls, it can cause bodily injury and equipment damage.

Redundant Power Supply Connection—Electrical Hazard

This product includes a redundant power or a blank in its place. In case of a blank power supply, do not operate the product with the blank cover

removed or not securely fastened.

Double Pole/Neutral Fusing

This system has double pole/neutral fusing. Remove all power cords before opening the cover of this product or touching any internal parts.

Multiple Power Inlets

Risk of electric shock and energy hazard. The PSUs are all independent. Disconnect all power supplies to ensure a powered down state inside of

the switch platform.

During Lightning—Electrical Hazard

During periods of lightning activity, do not work on the equipment or connect or disconnect cables.

Copper Cable Connecting/Disconnecting

Copper cables are heavy and not flexible, as such they should be carefully attached to or detached from the connectors. Refer to the cable

manufacturer for special warnings/instructions.

Rack Mounting and Servicing

When this product is mounted or serviced in a rack, special precautions must be taken to ensure that the system remains stable. In general, the

rack should be filled with equipment starting from the bottom to the top.

Equipment Installation

This equipment should be installed, replaced, and/or serviced only by trained and qualified personnel.

Equipment Disposal

Disposal of this equipment should be in accordance to all national laws and regulations.

Local and National Electrical Codes

This equipment should be installed in compliance with local and national electrical codes.

Installation Codes

This device must be installed according to the latest version of the country national electrical codes. For North America, equipment must be installed

in accordance to the applicable requirements in the US National Electrical Code and the Canadian Electrical Code.

Battery Replacement

Warning: Replace only with UL Recognized battery, certified for maximum abnormal charging current not less than 4mA. There is a risk of explosion

should the battery be replaced with a battery of an incorrect type. Dispose of used batteries according to the instructions.

UL Listed and CSA Certified Power Supply Cord

For North American power connection, select a power supply cord that is UL Listed and CSA Certified, 3 - conductor, [16 AWG], terminated with a

molded plug rated at 125 V, [13 A], with a minimum length of 1.5m [six feet] but no longer than 4.5m.

For European connection, select a power supply cord that is internationally harmonized and marked “<HAR>”, 3 - conductor, minimum 1.0 mm2

wire, rated at 300 V, with a PVC insulated jacket. The cord must have a molded plug rated at 250 V, 10 A.

Installation Codes

This device must be installed according to the latest version of the country's national electrical codes. For North America, equipment must be

installed in accordance to the applicable requirements in the US National Electrical Code and the Canadian Electrical Code.

Interconnection of Units

Cables for connecting to the unit RS232 and Ethernet Interfaces must be UL certified type DP-1 or DP-2. (Note: when residing in non LPS circuit.)

Overcurrent Protection

A readily accessible Listed branch circuit overcurrent protective device rated 20 A must be incorporated in the building wiring.

Do Not Use the Switch as a Shelf or Work Space

Caution: Slide/rail mounted equipment is not to be used as a shelf or a work space. The rails are not intended for sliding the unit away from

the rack. It is for permanent installation at final resting place only, not used for service and maintenance.

WEEE Directive

According to the WEEE Directive 2002/96/EC, all waste electrical and electronic equipment (EEE) should be collected separately and not

disposed of with regular household waste. Dispose of this product and all of its parts in a responsible and environmentally-friendly way.

Country of Norway Power Restrictions

This unit is intended for connection to a TN power system and an IT power system of Norway only.

Air Flow

systems are offered with two air flow patterns:

The following information does not apply to SN2100/SN2010. In the SN2100/SN2010 systems, the fan units are non-replaceable.

Power (rear) side inlet to connector side outlet - marked with blue power supplies/fans FRUs’ handles.

Air Flow Direction Marking - Power Side Inlet to Connector Side Outlet

Connector (front) side inlet to power side outlet - marked with red power supplies/fans FRUs’ handles.

Air Flow Direction Marking - Connector Side Inlet to Power Side Outlet

The table below provides an air flow color legend and respective OPN designation.

Direction Description and OPN Designation

Connector side inlet to power side outlet. Red latches are placed on the power inlet side.

“-R”.OPN designation is

Power side inlet to connector side outlet. Blue latches are placed on the power inlet side.

“-F”.OPN designation is

Package Contents

Before installing your new system, unpack it and check against the parts list below that all the parts have been sent. Check the parts for visible damage

that may have occurred during shipping.

The SN2700 and SN2410 package content is as follows:

1 – System

1 – Rail kit

1 – Power cable for each power supply unit – Type C13-C14

1 – Cable retainer for each power supply unit

1 – DB9 to RJ-45 2m harness

1 - RJ-45 to RJ-45 2m harness

The SN2100/SN2010 package content is as follows:

1 – System

1 – Power cable for each power supply unit – Type C13-C14

1 – DB9 to RJ-45 2m harness

All servers and systems in the same rack should be planned with the same airflow direction.

All FRU components need to have the same air flow direction. A mismatch in the air flow will affect the heat dissipation.

19” System Mounting Options

By default, the SN2700 systems are shipped with the static rail kit described .SN2700 Static Rail Kit

The SN2410 and SN2740 systems are shipped with the static rail kit described in . SN2740/SN2410 Static Rail Kit

For the telescopic rail kit installation instructions (can be used with SN2700 only), see . SN2700 Telescopic Rail Kit

The SN2100/SN2010 system is shipped without a rail kit and a designated rail kit can be purchased separately. For installation instructions, see S

.N2100/SN2010 Side by Side Mounting Rail Kit

SN2100/SN2010 Static Single Switch Rail Kit

A designated rail kit for the SN2100/SN2010 systems can be purchased separately.

If anything is damaged or missing, contact your sales representative at .[email protected]

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nvidia Computerhardware Handbücher

Nvidia

Nvidia DGX H100 Bedienungsanleitung

Nvidia

Nvidia Mellanox ConnectX-6 Dx Series Bedienungsanleitung

Nvidia

Nvidia Mellanox ConnectX-5 Bedienungsanleitung

Nvidia

Nvidia TESLA M2090 Bedienungsanleitung

Nvidia

Nvidia SP5200BLT Bedienungsanleitung

Nvidia

Nvidia Mellanox ConnectX-5 Bedienungsanleitung

Nvidia

Nvidia Tegra 250 Referenzhandbuch

Nvidia

Nvidia Jetson AGX Orin Series Installations- und Betriebsanleitung

Nvidia

Nvidia PCI Express Series Bedienungsanleitung

Nvidia

Nvidia nForce 680I LT SLI Gebrauchsanweisung

Nvidia

Nvidia DGX-2 SYSTEM Bedienungsanleitung

Nvidia

Nvidia JETSON TX2 Bedienungsanleitung

Nvidia

Nvidia FX4500 - Apple MAC Pro QUADRO FX 4500 Video Card... Kurzanleitung

Nvidia

Nvidia DGX A100 Bedienungsanleitung

Nvidia

Nvidia AVerMedia D133 Series Bedienungsanleitung

Nvidia

Nvidia Quadro M6000 Sync Bedienungsanleitung

Nvidia

Nvidia RTX 6000 Bedienungsanleitung

Nvidia

Nvidia TESLA K20 Bedienungsanleitung

Nvidia

Nvidia Jetson Orin NX Leitfaden

Nvidia

Nvidia ConnectX-6 Dx MCX623432AE-ADAB Bedienungsanleitung

Nvidia

Nvidia Tesla C870 Bedienungsanleitung

Nvidia

Nvidia Mellanox ConnectX-5 Handbuch

Nvidia

Nvidia GeForce2 Ti SP6600Ti Bedienungsanleitung

Nvidia

Nvidia MCP 78S Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung