NXP Semiconductors MCIMX93-EVKCM Bedienungsanleitung

QUICK START GUIDE

MCIMX93-EVKCM

i.MX 93 APPLICATIONS PROCESSOR

i.MX i.MX 93 EVKCM

APPLICATIONS PROCESSOR QSG

ABOUT THE i.MX 93 EVKCM

The i.MX 93 applications processor is the latest member of the

i.MX 9 family. It excels in machine learning, vision, advanced multimedia

and industrial IoT applications. Elevating edge intelligence, i.MX 93

processors are the solid foundation for products built for smart homes,

smart cities, and industrial applications.

QUICK START GUIDE

MCIMX93-EVKCM

i.MX 93 APPLICATIONS PROCESSOR

FEATURES

SOM Module

• i.MX 93 applications processor

with:

–2x Arm®Cortex®-A55

–1× Arm®Cortex®-M33

–0.5 TOPS NPU

• LPDDR4X 16-bit 2GB

• eMMC 5.1, 32GB

• Power Management IC (PMIC)

• Power Measurement ADC

Base Board

• MicroSD 3.0 card slot

• Two USB 2.0 C connector

• One USB 2.0 C for Debug

• One USB C PD only

• M.2 Key-E for Wi-Fi/BT/802.15.4

• One MIPI-CSI connector

• One CAN port

• Four channels for ADC

• 6-axis IMU w/ I3C support

• I2C Expansion connector

• Two 1 Gbps Ethernet

–Port0 supports ETER

–Port1 supports TSN

• Multiple display interface:

–MIPI-DSI connector

–1x4 data lane LVDS w/ Backlight

• Audio Codec Support

• PDM MIC array support

• External RTC w/ coin cell

• 2X20 Pin Expansion I/O

GET TO KNOW THE i.MX 93 EVKCM

USB C PDUSB C PDUSB CUSB C

DebugDebug Audio JackAudio JackUSB2.0 C x2USB2.0 C x2 GbE RJ45 x2GbE RJ45 x2

II22C EXPC EXPMIPI CSIMIPI CSI

ADCADCMIPI DSIMIPI DSI LVDS / Back LightLVDS / Back Light

PDM MICPDM MIC

GPIO EXPGPIO EXP

MicroSDMicroSD

Figure 1: Top view i.MX 93 11x11 EVKCM board

CANCAN

RDPM I/FRDPM I/F

JTAGJTAG

M.2 slotM.2 slot

QUICK START GUIDE

MCIMX93-EVKCM

i.MX 93 APPLICATIONS PROCESSOR

GET TO KNOW THE i.MX 93 EVKCM CONTINUED

M.2 slot (E-KEY)M.2 slot (E-KEY)

Figure 2: Back view i.MX 93 11x11 EVKCM board

GETTING STARTED

Table 1 — Kit Contents

ITEM DESCRIPTION

MCIMX93-EVKCM i.MX 93 11X11 EVKCM board

Power Supply USB C PD 45W, 5V/3A; 9V/3A; 15V/3A; 20V/2.25A supported

USB Type-C Cable USB 2.0 C Male to USB 2.0 A Male

Software Linux BSP image programmed in eMMC

Documentation Quick Start Guide

Table 2 — Customer Supplied Accessories

ITEM DESCRIPTION

IMX-MIPI-HDMI MIPI-DSI to HDMI adapter board

LVDS LCD 12.1” TFT LCD, 1280x800 RGB

RPi-CAM-MIPI IAS camera to RPi camera adapter (AR0144 sensor)

Audio HAT Audio expansion board with most of audio features

M.2 Module PN: LBES5PL2EL; Wi-Fi 6 / BT 5.2 / 802.15.4 support

Contact [email protected] to obtain a free sample

Unpack the Kit

The MCIMX93-EVKCM is shipped with the items listed in Table 1.

Prepare Accessories

The following items in Table 2 are recommended to run the

MCIMX93-EVKCM.

QUICK START GUIDE

MCIMX93-EVKCM

i.MX 93 APPLICATIONS PROCESSOR

GETTING STARTED

CONTINUED

Download Software and Tools

Installation software and documentation are available

at www.nxp.com/imx93evkcm. The following are available

on the website:

Table 3 — Software and Tools

ITEM DESCRIPTION

Documentation

• Schematics, layout and Gerber files

• Quick Start Guide

• Hardware Design Guide

• i.MX 93 EVKCM Board User Manual

• Power Consumption Measurement

Software Development • Linux BSPs

Demo Images

• SCopy of the latest Linux®images that are available to program

on to the eMMC

• MCIMX93-EVKCM software can be found at nxp.com/imxsw

1Confirm Boot

Switches

The boot switches should be set to boot

from “eMMC”, SW1301[1-4] (Figure 1) are used

for boot, See table below:

2Connect USB

Debug Cable

Connect the UART cable into the port JP1401

(Figure 1). Connect the other end of the cable to

a PC acting as a host terminal. UART connections

will appear on the PC, this will be used as A55

and M33 core system debugging.

Open the terminal window (i.e., Hyper Terminal

or Tera Term), choose the right COM port number

and apply the following configuration.

• Baud rate: 115200bps

• Data bits: 8

• Parity: None

• Stop bits: 1

3Connect LVDS

panel Display

Connect an LVDS panel with J702 2x20 PIN header

through cable. Make sure jumpers on J703 (P2-P3)

and J704 (P2-P1) have been installed.

4Connect

Mouse

Connect the mouse to the USB2 C port connector

J302 through USB C OTG cable.

SETTING UP THE SYSTEM

The following will describe how to

run the pre-loaded Linux image on

the MCIMX93-EVKCM (i.MX 93).

BOOT DEVICE SW1301[1-4]

eMMC/uSDHC1 0000

5Connect

Power Supply

Connect the USB C PD power supply to J301,

then power up the board by SW301 switch.

QUICK START GUIDE

MCIMX93-EVKCM

i.MX 93 APPLICATIONS PROCESSOR

SETTING UP THE SYSTEM

CONTINUED

6Board

Boot Up

As the board boots up, you will see 4 penguins

appear in the upper left-hand corner of the

monitor, and then you will see the Linux terminal

Icon on the top left and timer on right top corner .

Congratulations, you are up and running.

J301J301

J704J704 J703J703 J702J702

J1401J1401 J302J302

JW301JW301

ADDITIONAL INFORMATION

Boot Switches

SW1301[1-4] is the boot configuration switch, the default boot device

is eMMC/uSDHC1, as shown in Table 4. If you want to try other boot

devices, you need to change the boot switches to corresponding

values as listed in Table 4.

Note: 1 = ON 0 = OFF

Inhaltsverzeichnis

Andere NXP Semiconductors Computerhardware Handbücher

NXP Semiconductors

NXP Semiconductors UM10694 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors KW45B41Z-EVK Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors winbond MCX-N9 BRK Series Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors OM13489 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors HRPNUG Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors UM11653 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MCU-Link Pro Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors SABRE i.MX 6 Series Montageanleitung

NXP Semiconductors

NXP Semiconductors MCIMX7SABRE Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors freescale MPC837xE-RDS Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors QN908 series Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors OM15080-JN5189 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors i.MX 8M Mini LPDDR4 EVK Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MCF5272 ColdFire Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors S32G-VNP-EVB Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors SLN-VIZNLC-IOT Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors freescale MC92604 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors TWR-PXS2010 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors OM15080-K32W Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors freescale MC9S12G128 MCU Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors AN11211 Fehlerbehebungshandbuch

NXP Semiconductors

NXP Semiconductors IMXRT500HDG Leitfaden

NXP Semiconductors

NXP Semiconductors freescale MED-GLU Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors i.MX RT1170 Montage- und Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung