NXP Semiconductors ISP1183 Bedienungsanleitung

UM10044

ISP1183 Low-Power USB Peripheral Controller PC Eval Kit

Rev. 04 — 6 February 2007 User manual

Document information

Info Content

Keywords isp1183, universal serial bus, usb

Abstract This document explains the ISP1183 PC eval kit.

NXP Semiconductors UM10044

ISP1183 Low-Power USB Peripheral Controller PC Eval Kit

Revision history

Contact information

For additional information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Rev Date Description

04 20070206 Third release; updated Section 8.

03 20041021 Third release; updated the schematics.

02 20041018 Second release; updated Table 1. Updated terminology from “device PC” to “peripheral

PC”, and “interface device” to peripheral controller”.

01 20030930 First release.

User manual Rev. 04 — 6 February 2007 2 of 18

NXP Semiconductors UM10044

ISP1183 Low-Power USB Peripheral Controller PC Eval Kit

1. Introduction

The ISP1183 is a cost- and feature-optimized Universal Serial Bus (USB) peripheral. It is

typically used in any microcontroller- or microprocessor-based system. The ISP1183 is a

full-speed USB Peripheral Controller with up to 14 configurable endpoints. It has a fast

general-purpose parallel interface to communicate with many types of microcontrollers or

microprocessors.

The ISP1183 has 2462 bytes of internal First In, First Out (FIFO) memory, which is

shared among enabled USB endpoints. The type and FIFO size of each endpoint can be

individually configured, depending on the required packet size. For increased data

throughput, isochronous and bulk endpoints are double-buffered.

To a microcontroller, the ISP1183 appears as a memory device with an 8-bit data bus

and a 1-bit address bus. The ISP1183 only supports a nonmultiplexed address and data

bus.

The ISP1183 PC evaluation (eval) kit uses two PCs as a complete USB development

environment, a host PC with USB host capability and a peripheral PC running the

ISP1183 firmware. The ISP1183 eval board is plugged in the peripheral PC as a USB

peripheral.

With this set up, you can easily evaluate the features of the ISP1183, and develop

firmware and product prototype, without being limited by the choice of a microcontroller.

The firmware is written in C, that supports Borland Turbo C for x86.

Fig 1 shows the ISP1183 eval board.

Fig 1. ISP1183 eval board

2. System requirements

For the host PC:

• PC with USB motherboard or add-on card.

• Microsoft Windows 98 and Windows 2000.

For the peripheral PC:

• PC with Microsoft DOS 6.x.

• ISP1183 eval board, as shown in Fig 2.

User manual Rev. 04 — 6 February 2007 3 of 18

NXP Semiconductors UM10044

ISP1183 Low-Power USB Peripheral Controller PC Eval Kit

For the firmware development:

• x86 CPU platform: Borland Turbo C++ 3.0 or above.

• ISP1183 eval diskette.

Fig 2. System structure of the ISP1183 PC eval kit

3. Jumper settings on the ISP1183 eval board

The ISP1183 eval board is plugged into the peripheral PC. It will occupy I/O and IRQ

resources of the peripheral PC. To avoid possible conflicts in settings, remove all

unnecessary cards from the peripheral PC. Sound cards and network cards may cause

IRQ conflicts.

Jumper JP1 enables and disables the level-shift module.

Table 1. JP1

Isolate data bus Disable Enable (default)

Short pins 1 - 2 2 - 3

JP2 sets the I/O power supply of the eval board. Default setting is 1.8 V.

Table 2. JP2

I/O voltage select 1.8 V (default) 3.3 V

Short pins 1 - 2 2 - 3

User manual Rev. 04 — 6 February 2007 4 of 18

NXP Semiconductors UM10044

ISP1183 Low-Power USB Peripheral Controller PC Eval Kit

JP4 sets the IRQ number for the ISP1183 eval board. Default setting is IRQ5 as shown

in Table 3. Short Intx_IRQ and pin 5.

Table 3. JP4

IRQ number IRQ5 (default) IRQ3 IRQ4 IRQ6 IRQ7

Short pins 5 - Intx_IRQ 3 - Intx_IRQ 4 - Intx_IRQ 6 - Intx_IRQ 7 - Intx_IRQ

Jumper JP5 is reserved (left open).

Table 4. S2

Microcontroller power supply 5 V (default) 3.3 V

Short pins 1 - 2 2 - 3

Table 5. S4

Board power supply Bus-powered Self-powered (default)

Short pins 1 - 2 2 - 3

Table 6. S5

VBUS power supply Bus-powered (default) Self-powered

Short pins 1 - 2 2 - 3

Table 7. Possible conflict settings

IRQ number Possible conflict

IRQ5 Creative SoundBlaster and compatible sound cards always occupy this IRQ, by

default. If this type of sound card is installed, check its settings or remove it.

Some network cards may also use this IRQ.

IRQ7 Used by parallel port, by default. May cause printing problem on peripheral PC.

4. I/O mapping

The ISP1183 eval board occupies eight I/O locations. The base address is 368h.

Table 8. I/O mapping

Offset Usage

0 ISP1183 data register, read or write

1 Write command register, read data bus state

2 Board control and read chip I/O state

3 Reserved

4 to 7 Reserved for expansion board

User manual Rev. 04 — 6 February 2007 5 of 18

NXP Semiconductors UM10044

ISP1183 Low-Power USB Peripheral Controller PC Eval Kit

5. Installing hardware, firmware, INF and driver

The procedure to install hardware, firmware, INF and driver is as follows:

1. Switch off the peripheral PC.

2. Remove all unnecessary cards on the peripheral PC.

3. Plug the ISP1183 eval board in the ISA slot of the peripheral PC.

4. Switch on the peripheral PC.

5. On the peripheral PC, under the DOS mode, run firmware 1183FW.EXE.

If it is the first time that the eval board is connected to the host PC, the host OS Device

Manager will prompt for the installation of INF and drivers.

6. Select the location of D13TEST.INF and D13TEST.SYS from the ISP1183 evaluation

diskette and complete the installation procedure.

6. Using the host applet

Test applet D13TEST.EXE exercises all the ISP1183 endpoints as shown in Fig 3.

Fig 3. D13Test applet

Table 9 shows a description of endpoints operation on the ISP1183 eval board.

User manual Rev. 04 — 6 February 2007 6 of 18

NXP Semiconductors UM10044

ISP1183 Low-Power USB Peripheral Controller PC Eval Kit

Table 9. Description of endpoints operation

The test applet and the ISP1183 eval board support three test modes: loopback, print

and scan. The firmware uses I/O accesses on this endpoint.

Endpoint number Endpoint type Operations

5 ISO-OUT This pipe is defined as an isochronous OUT pipe.

6 ISO-IN This pipe is defined as an isochronous IN pipe.

3 Bulk-OUT This pipe is defined as a bulk OUT pipe. Supports DMA.

4 Bulk-IN This pipe is defined as a bulk IN pipe. Supports DMA.

Three test modes:

• Scan mode: In this mode, the ISP1183 eval board acts like a scanner. It sends data

packets to the host PC as fast as possible. Use this mode to evaluate the

isochronous IN and bulk IN transfer rates.

• Print mode: In this mode, the ISP1183 eval board acts like a printer. It receives data

packets from the host PC as fast as possible. Use this mode to evaluate the

isochronous OUT and bulk OUT transfer rates.

• Loopback mode: In this mode, the ISP1183 eval board receives data packets on the

isochronous OUT (or bulk OUT) endpoint and sends them back to the host PC on

isochronous IN (or bulk IN) endpoint. Use this mode to test the data integrity of

transfers.

The Buffer Size setting of the test applet is determined by firmware and hardware ability

of the eval board. For ISA mode, the maximum size is limited to 64000 bytes for the bulk

transfer and 256 bytes for the ISO transfer. For ISO scan mode, if you need to change

the buffer size, print a buffer of the same data size first. By default, Buffer Size is set to

64000 when the test applet is launched. Change Buffer Size to 64 before starting the

test.

Repeat Times for the loopback test controls the numbers of iterations of loopback, which

is useful for debugging. By default, Repeat Times is set to 0 when the test applet is

launched. To run the test infinite times, set Repeat Times to –1.

7. Testing control endpoints using standard USB compliance tool

To test control endpoints using the standard USB compliance tool:

1. Run the USB compliance tool.

The USB Compliance Tool1window appears, as in Fig 4.

2. Connect a USB peripheral.

1. In this document, names of windows and dialog boxes are indicated in italic.

User manual Rev. 04 — 6 February 2007 7 of 18

NXP Semiconductors UM10044

ISP1183 Low-Power USB Peripheral Controller PC Eval Kit

Fig 4. USB Compliance Tool window

3. In the USB Compliance Tool window, click the Full Test2 button.

Fig 5. Device Framework Tests dialog box

2. In this document, items that you click or type are indicated in bold.

User manual Rev. 04 — 6 February 2007 8 of 18

NXP Semiconductors UM10044

ISP1183 Low-Power USB Peripheral Controller PC Eval Kit

4. In dialog box Device Framework Tests, as seen in Fig 5, deselect Perform Remote

Wakeup and select In A Continuous Loop.

5. Click the Start Automated Testing button.

The Full Test Results dialog box appears, as seen in Fig 6.

6. To stop the loop test, click Stop Testing.

Fig 6. Full Test Results dialog box

The USBCV testing tool can be downloaded from the USB website. Check the website

for the latest version of the tool.

User manual Rev. 04 — 6 February 2007 9 of 18

NXP Semiconductors UM10044

ISP1183 Low-Power USB Peripheral Controller PC Eval Kit

8. Schematics

C13

bus-power

BLM21P221SG

0.47 μF

0.04 Ω, 1%

1/2W

RSENSE1

MMSF3PO2HD

CDRH125-220

MBRS340T3

220 μF/10 V

DC1

1 kΩ

0.04 Ω, 1% 1/2W

RSENSE2

MMSF3PO2HD

CDRH125-220

MBRS340T3

100 μF/10 V

DC2

10 kΩ,1%

26 kΩ,1%

220 pF

V(1V8)

VCC(3V3)

OUT

FB3/5 EXT

REF

4V+ 5

CS 6

GND 8

SHDN

MAX1626

OUT

FB3/5 EXT

REF

4V+ 5

CS 6

GND 8

SHDN

MAX1627

S5 VBUS_N

VCC

self-power

IN5401

ISA-5V

22 μF/10 V

DC4

100 μF/10 V

DC3

V(1V8)

VCC VCC

100 Ω

R28

100 Ω

R29

JP2

VCC(3V3)

100 μF/10 V

DC5 47 μF/10 V

DC6

IN5401

VDD 1

DGND 2

DGND 3

8~15V DC IN

CON6

Vin

GND

+5 V 2

LM7805

220 μF/50 V

C35

C34

IN5401

self-power

100 μF

C36 VBUS L3

Power supply module

0.1 μF

0.1 μ

Fig 7. Power supply module

RDX

WRX

CSX

RSTX

INTX

VBUSONX

SUSPEND

WAKEUP

UD7

UD6

UD5

UD4

UD3

UD2

UD1

UD0

DB5

BRD

DB3

DB2

BA0

DB6

DB7

DB1

BWR

BWAKEUP

DB4

DB0

BCS

BRST

BVBUSON

BSUSPEND

BINTX

VCC(3V3) VCC(3V3)

C23 C24

C19

C20

C21

C22

V(1V8)

OE OE

JP1

4.7 kΩ

R18

RDWR

VCC(3V3) DIR 1

1B1 2

1B2 3

GND 4

1B3 5

1B4 6

VCCB 7

1B5 8

1B6 9

GND 10

1B7 11

1B8 12

2B1 13

2B2 14

GND 15

2B3 16

2B4 17

VCCB 18

2B5 19

2B6 20

GND 21

2B7 22

2B8 23

2DIR 24

1OE

48 1A1

47 1A2

46 GND

45 1A3

44 1A4

43 VCCA

42 1A5

41 1A6

40 GND

39 1A7

38 1A8

37 2A1

36 2A2

35 GND

34 2A3

33 2A4

32 VCCA

31 2A5

30 2A6

29 GND

28 2A7

27 2A8

26 2OE

P174AVC164245

DIR 1

1B1 2

1B2 3

GND 4

1B3 5

1B4 6

VCCB 7

1B5 8

1B6 9

GND 10

1B7 11

1B8 12

2B1 13

2B2 14

GND 15

2B3 16

2B4 17

VCCB 18

2B5 19

2B6 20

GND 21

2B7 22

2B8 23

2DIR 24

1OE

48 1A1

47 1A2

46 GND

45 1A3

44 1A4

43 VCCA

42 1A5

41 1A6

40 GND

39 1A7

38 1A8

37 2A1

36 2A2

35 GND

34 2A3

33 2A4

32 VCCA

31 2A5

30 2A6

29 GND

28 2A7

27 2A8

26 2OE

P174AVC164245

TEST30 TEST31

DACK DACK'

DREQ'DREQ

Level shift module

0.1 μF

0.1 μF0.1 μF

Fig 8. Level shifter module

User manual Rev. 04 — 6 February 2007 10 of 18

Inhaltsverzeichnis

Andere NXP Semiconductors Controller Handbücher

NXP Semiconductors

NXP Semiconductors MPC560xB Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PD3DB1548 PD3.0 type-C Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MC13224V Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors OM5577 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors OM5579 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors 56800E Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors BLDC Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MPC5644A Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MPC560xP Leitfaden

NXP Semiconductors

NXP Semiconductors K22F series Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MC9S12ZVH64 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors TWR-VF65GS10-PRO Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PN7150X Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors LPC2917 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MK30DX64VMC7 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PN5331B3HN Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PXN2020 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors DSP56800E Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors 56F8300 Series Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PCA9665 Betriebshandbuch

NXP Semiconductors

NXP Semiconductors PN7150 Leitfaden

NXP Semiconductors

NXP Semiconductors freescale 56F8014 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PN7150 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MC9328MX1 Handbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung