NXP Semiconductors PD3DB1548 PD3.0 type-C Bedienungsanleitung

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: [email protected]

Doc. ID: USB-PD/QC4.0_DevKit Date of release: 30 March 2018

NXP Semiconductors

USB-PD/QC4.0 Development Kit A

Quick Start Guide for USB-PD/QC4.0 Development Kit

1. Introduction

This document describes how to use the QC4pDB1532 Portway adapter and the

TEA1936xDB1530 demo board with the SP05127-05 demonstration kit.

1.1 Contents

Fig 1. SP05127-05 demonstration kit

This kit contains:

•PD3DB1548 PD3.0 type-C tester.

•Portway 27W Global Travel Charger

•1 × type-C cable, 1 m

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: [email protected]

Doc. ID: USB-PD/QC4.0_DevKit Date of release: 30 March 2018

NXP Semiconductors

USB-PD/QC4.0 Development Kit A

Quick Start Guide for USB-PD/QC4.0 Development Kit

2. Safety requirements

This kit is to be used in combination with a QC4pDB1532 Portway adapter and a

TEA1936xDB1530 demo board. For supplying this application AC power with galvanic

isolation from the mains is strongly advised, as the TEA1936xDB1530 demo board is

connected to AC power. For supplying the TEA1936xDB1530 demo board a mains

isolated transformer/variac or an AC power source can be used.

Use a protective shield over the TEA1936xDB1530 demo board and never touch the

board when testing, i.e. with mains power on. After switching off the mains power, do not

touch the primary part of the board (red area), because the electrolytic buffer capacitors

will remain charged for several minutes. Only handle the board at the secondary side

(green) after testing, see Fig 2.

Fig 2. Beware of the primary circuit!

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: [email protected]

Doc. ID: USB-PD/QC4.0_DevKit Date of release: 30 March 2018

NXP Semiconductors

USB-PD/QC4.0 Development Kit A

Quick Start Guide for USB-PD/QC4.0 Development Kit

3. How to use

3.1 PD 3.0 Type-C tester

The PD3DB1548 PD 3.0 Type-C tester is shown in Fig 3.

Fig 3. PD3DB1548 PD 3.0 Type-C tester

This board is used for PD 3.0 and 4.0(+) evaluation. A load and/or a voltage meter can

be connected to T2 and T3 to measure the output voltage and to draw current from the

USB-PD application with a resistive or electronic load.

The board is connected to the demo board via the Type-C port. The board can be

supplied by the Type-C application under test, but also via an external +5 V supply that is

connected to the micro USB port CN1.

The supply select switch needs to be set in the correct position. In the photograph the

switch is set for supply via the Type-C connection.

The board is connected to a charger application via the Type-C port.

For USB-PD 3.0 the board can be used to select the desired PDO by pressing the

corresponding switches. The on-board display shows the value of the output voltage

V(bus).

For USB-PD 4.0(+) this version of the Type-C tester will also work. Pressing V_Up or

V_down will increase or decrease the output voltage respectively with 20 mV steps.

Holding V_Up or V_Down pressed down will result in the maximum or minimum voltage

of the selected PDO respectively when PPS is enabled for that particular PDO.

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: [email protected]

Doc. ID: USB-PD/QC4.0_DevKit Date of release: 30 March 2018

NXP Semiconductors

USB-PD/QC4.0 Development Kit A

Quick Start Guide for USB-PD/QC4.0 Development Kit

3.2 Testing the Portway 27 Watt adapter

The diagram in Fig 4 shows how the Portway adapter can be tested with the Type-C

tester.

Fig 3

Fig 4. Testing the NXP powered Portway 27 Watt adapter.

Table 1. Portway PDO settings

Portway 27 Watt adapter

PDO #

V(out) [V]

I(out,max) [A]

PPS [y/n]

2.25

3.3 .. 5.9

3.3 .. 11.0

2.45

All PDO’s in the Portway adapter are now easily accessible with the Type-C tester,

although it is recommended to use the PD3QC4DB1547 which is equipped with a 4 digit

display which shows the voltage as intended for QC4/PPS when V(out) ≥ 10 V.

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: [email protected]

Doc. ID: USB-PD/QC4.0_DevKit Date of release: 30 March 2018

NXP Semiconductors

USB-PD/QC4.0 Development Kit A

Quick Start Guide for USB-PD/QC4.0 Development Kit

3.3 Testing the TEA1936xDB1530 demo board

The diagram in Fig 5 shows how the TEA1936xDB1530 demo board can be tested with

the Type-C tester.

Fig 5. Testing the TEA1936xDB1530 demo board

Table 2. Demo board PDO settings

TEA1936xDB1530 27 Watt adapter

PDO #

V(out) [V]

I(out,max) [A]

PPS [y/n]

2.25

3.3 .. 5.9

3.3 .. 11.0

Also here all PDO’s in the demo board are easily accessible with the Type-C tester,

although it is recommended to use the PD3QC4DB1547 which is equipped with a 4 digit

display which shows the voltage as intended for QC4/PPS when V(out) ≥ 10 V.

Inhaltsverzeichnis

Andere NXP Semiconductors Controller Handbücher

NXP Semiconductors

NXP Semiconductors K22F series Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PN7120 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PN7150 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MK30DX64VMC7 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors freescale 56F8014 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors LPC2917 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PXN2020 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PN7150X Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MC9S12ZVH64 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PCA9665 Betriebshandbuch

NXP Semiconductors

NXP Semiconductors 56800E Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors 56F803 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PT2001 Betriebsanleitung

NXP Semiconductors

NXP Semiconductors MPC5644A Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MC13224V Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PN7150 Leitfaden

NXP Semiconductors

NXP Semiconductors ISP1183 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors LPC1768 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors TWR-VF65GS10-PRO Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors DSP56800E Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors LPC1311 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors UM10204 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors OM5579 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PN5331B3HN Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung