NXP Semiconductors TWR-KL25Z Bedienungsanleitung

TWR-KL25Z Tower Module

Revision C ERRATA

TWR-KL25Z-ERRATA

Rev. 1.1

TWRKL25Z Tower Module Errata Page 2 of 4

1ERRATA

This document describes errata on the TWR-KL25Z rev. C board as well as their workarounds.

1.1 External jtag usage

1.1.1 Issue description

The usage of level shifters in the communication between the integrated debugger (OpenSDA) and the target MCU

(KL25) is needed because the OpenSDA debugger runs at 3.3 volts while the KL25 can run at 3.3 or 1.8 volts. One of

the level shifters that is used in the circuit is configured for a fixed direction of communication, which means that

when not in use by the OpenSDA, the pin is kept in a fixed state. This fixed state inhibits external debuggers to work

when the OpenSDA is powered (by connecting the mini USB connector).

The problematic signal is highlighted below.

1.1.2 Workaround

To avoid the OpenSDA keeping this signal fixed so that an external debugger can be used, the OpenSDA needs to be

unpowered. There are two available ways to power the board without powering the OpenSDA:

-Power through elevators: use the tower elevators and power the board through them.

-Stand-alone through the micro USB: the TWR-KL25Z includes a micro USB connector that is connected to the

USB port in the KL25 device. The power input from this USB port is connected to the internal KL25 USB

regulator and this regulator output can be routed to power the board by placing to jumpers (J6 and J18) in

TWRKL25Z Tower Module Errata Page 3 of 4

the board.

Care should be taken to avoid connecting the OpenSDA mini USB at the same time, because this may cause

a short circuit!

1.2 Reset button

When the OpenSDA is not powered the reset button does not work. This is because the reset button has

been placed in the OpenSDA side of the level shifter for the reset signal.

To be able to use the reset button, it is needed to power the OpenSDA circuit. This issue does not inhibit

the POR or the external debugger reset.

1.3 Pull-ups missing from the TWRPI connector IIC

1.3.1 Issue description

The IIC signals connected to the TWRPI connector (J4, pins 1 and 2) are missing their pull-ups. These signals

are also connected to the elevator IIC signals (I2C0_SCL and I2C0_SDA) so they are also missing pull-ups if

IIC communication is needed for peripheral boards.

1.3.2 Workaround

Pull-ups can be connected to these signals externally by using the tower elevator lateral connectors. Using

through-hole resistors, connect a 2.2 k to 10 k ohm resistor. Connect between pins 7 and 3 and pins 8 and 3

of the primary elevator top lateral connector as showed in the figure below.

TWRKL25Z Tower Module Errata Page 4 of 4

Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.

All other product or service names are the property of their respective owners.

Inhaltsverzeichnis

Andere NXP Semiconductors Mikrocontroller Handbücher

NXP Semiconductors

NXP Semiconductors UM11527 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors LPC55S0x Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors LPC5411 Series Betriebshandbuch

NXP Semiconductors

NXP Semiconductors UG10068 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors Freescale Xtrinsic LFSTBEB865X Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors LPC5500 Series Referenzhandbuch

NXP Semiconductors

NXP Semiconductors NTAG I2C plus Gebrauchs- und Pflegehandbuch

NXP Semiconductors

NXP Semiconductors ASUG Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors KITMPXA6115AEVB Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors SAFE ASSURE Qorivva MPC5602P Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors i.MX 8M Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors UM10883 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors EdgeLock A5000 Montage- und Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors JN517x-DK005 Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors OM-SE051ARD Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors KE1xF Series Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors FRDM-KW41Z Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors AN10815 Montage- und Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors S12ZVML-MINIKIT Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MPC5606BK Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors A71CLARD-BA Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors Freescale 56800TDC Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors MTRCKTSPS5744P Bedienungsanleitung

NXP Semiconductors

NXP Semiconductors PN7462 series Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F800 Bedienungsanleitung

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Bedienungsanleitung