OAKWORKS Clodagh Libra Bedienungsanleitung

Libra™

INSTRUCTION MANUAL

www.oakworks.com · 717.235.6807

Oakworks®, Inc.

Manual Part # MMMNST0020

1st Edition, May 2010

Printed in U.S.A.

All rights are reserved. No

part of this document may be

photocopied, reproduced or

translated to another language

without prior written consent

of Oakworks®, Inc.

Oakworks®is a registered

trademark of Oakworks®, Inc.

Notice

The information contained in this document is

subject to change without notice and should not

be construed as a commitment by Oakworks®, Inc.

Oakworks®, Inc. assumes no responsibility for

any errors that may appear in this document nor

does it make expressed or implied warranty of

any kind with regard to this material, including,

but not limited to, the implied warranties of

merchantability and fitness for a particular purpose.

Oakworks®, Inc. shall not be liable for incidental

or consequential damages in connection with

or arising out of the furnishing, performance, or

use of this document and the program material

which it describes.

warnings / symbols

TABLE OF CONTENTS

Symbol Identification ............................................................................................ pg 2

Warnings & Safety Instructions ..................................................................... ....... pg 3

Grounding Instructions .................................................................................. ....... pg 6

Product Description & Table Specs .................................................................... pg 7

Installation & Leveling Instructions ............................................................... ....... pg 8

Directions for Use

Adjusting Height................................................................................. pg 9

Adjusting the Top............................................................................... pg 10

Important Safety Note.......................................................................................... pg 11

Side Arm Rests.................................................................................................. ..... pg 12

QuickLock Face Rest............................................................................................ pg 14

Foot Bath ....................................................................................................... pg 15

Foot Rest ....................................................................................................... pg 16

How to drain Foot Bath ........................................................................................ pg 16

Moving your Table .............................................................................................. pg 17

Care & Cleaning ................................................................................................. pg 18

How to clean the Foot Bath ................................................................................ pg 19

Power Lead Plugs ........................................................................................... ..... pg 20

Electrical Specifications.................................................................................. ..... pg 21

Warranty information ........................................................................................... pg 21

Contact Information .................................................................................. back cover

SYMBOL IDENTIFICATION

This symbol, when used in this manual and on product labels, represents a caution. Be

sure to read and comply with all precautions and warnings.

This symbol, when used in documentation on this product, indicates danger and warns

against an electrical shock hazard. Be sure to observe and comply with all warnings and

instructions.

This symbol, when used in documentation on this product, indicates a Protective

Earth (Ground) Terminal.

This symbol when used in documentation on this product, warns that during transport

there should be no stacking of containers.

This symbol, when used in documentation on this product, indicates that the product

should be protected from moisture. The humidity specifications for Transport &

Storage are listed in the back of this manual.

This symbol, when used in documentation on this product, indicates that information

is given regarding the recommended temperature limits during transport and storing.

The specifications for these limits are listed in the back of this manual.

This symbol, when used in documentation on this product, indicates the date of

manufacture of the device.

This symbol, when used in documentation on this product, indicates alternating

current (AC).

This symbol, when used in documentation on this product, indicates direct current

(DC).

This symbol, when used in documentation on this product, indicates that

instructional information is included. All instructions should be read carefully and

completely before using the equipment.

----

WARNINGS / SAFETY

Improper use of this device can cause injury. Be sure to read all

operating instructions prior to use to prevent injury to operator or client.

Electrical Shock Hazard.

• To reduce the risk of electric shock, always disconnect the

table from the electrical outlet before moving the table or doing

any maintenance or troubleshooting procedures. Never use this

equipment if it has a damaged cord or plug. Use this equipment

only for its intended use as described in these instructions. Do not

use any attachment or accessories not recommended by the manufacturer.

• The table MUST be connected to a Ground Fault Portected Outlet

with the detector in the main circuit breaker box (not on the outlet).

The GFCI included with the table is not sufficient for full protection.

• If a floor outlet is used, the outlet must not be recessed in the floor

(to prevent water entering the outlet in the event of an overflow).

To reduce the risk of burns, fire, electrical shock or injury:

• The power supply/control module is located under the top. Refer

servicing to qualified personnel and follow manual instructions

when doing any authorized troubleshooting.

• Before cleaning with any liquid cleaner be sure to un-plug the power cord

from the power outlet. Do not operate the table in standing water.

• Before moving the table, disconnect the power cord from the power outlet

and secure the electrical cord and foot control out of the way for moving.

• Never operate this table if it has a damaged cord or plug, if it is not working

properly, if it has been dropped or damaged, or dropped into water. Return

the table to a service center for examination and repair.

• Connect this appliance only to a properly grounded outlet. (See grounding

instructions below). Do not remove, modify or immerse the integral GFCI on

the power cord.

• DO NOT permit electric appliances (e.g. hair dryer, lamp, telephone, radio,

television, etc.) to be within 5 feet (1.5m) of this appliance.

• DO NOT reach for any electrical object that has fallen into the water.

Unplug immediately.

• Keep the cord away from heated surfaces.

• Do not use outdoors.

• Do not operate where aerosol (spray) products are being used or where

oxygen is being administered.

IMPORTANT WARNINGS & SAFETY INSTRUCTIONS

WARNINGS & SAFETY INSTRUCTIONS

READ AND

SAVE THESE

INSTRUCTIONS

DANGER

WARNING

READ WARNINGS CONTINUED ON NEXT PAGE

WARNINGS / SAFETY

WARNINGS & SAFETY INSTRUCTIONS

WARNINGS

CONTINUED

• This product is equipped with an interior accessory outlet (110V only).

The total electrical load plugged into this set of outlets is not to exceed

1000 watts.

• Risk of Injury – Children should never be near the table when in use.

Remove ON-Off key when not in use. (if applicable)

• Never drop or insert any object into any opening.

• Risk of accidental injury or drowning. Exercise care when entering or

exiting the foot bath. Invalid or disabled persons should not use a hydro

foot bath without trained supervision. Children are not allowed in the

vicinity of the equipment.

• Risk of scalding and possible drowning: Water temperature in excess of 104º F

(38º C) may be injurious to your health. Check and adjust water temperature

before use.

• Hydrotherapy should be pleasant and comfortable. Should you experience

any pain or discomfort while using the foot bath, discontinue use immedi-

ately and consult your physician.

• Consult your physician if you are diabetic, have poor circulation, if any area

of you feet or legs is inflamed, has an open wound or if you have any other

questions about whether you should be using hydro massage equipment.

• Unless thoroughly cleaned after each use, bath residue will buildup within

the jets and on the surface area of any whirlpool foot bath, which can pro-

mote the growth of bacteria.

• DO NOT operate water jets unless completely installed or without water

filled to the water level indicator above the jets.

• DO NOT over fill

• DO NOT stand on or in the foot bath. Use only while seated.

• Use the Foot Bath only for its intended purpose - to provide foot and ankle

hydro massage.

• DO NOT use attachments not recommended by the manufacturer.

• DO NOT sit on moveable leg rest. Max weight limit 125 lbs. (57 kg)

READ AND

SAVE THESE

INSTRUCTIONS IMPORTANT WARNINGS & SAFETY INSTRUCTIONS

WARNINGS / SAFETY

WARNINGS

WARNINGS & SAFETY INSTRUCTIONS

• Be certain that the table is completely lowered prior to

discharging an ambulatory patient. The patient may lose

balance and fall. Do not leave clients unattended when table is

set at its highest level.

• The table weighs as much as 225 lbs. (102 kg.) DO NOT lift

or move the unit without using proper safely procedures or

equipment. DO NOT turn the table on its side for any reason.

To do so could cause damage to the base and will void the warranty.

There are no serviceable items that require this action. Never

lift the table by grasping the table top as the table top is not

designed to hold the weight of the base and you could damage

the table.

• When operating the controls and making any and all adjustments

to the table, move hands and feet away from the working mechanism

of the table.

• The optional arm rests can be repositioned to allow a client to get

on and off the table easily. When making adjustments to the arm

rests, make certain that the client’s arms are away from the working

mechanism.

• DO NOT sit on arm rests, the elevated backrest or leg rest. DO

NOT put excessive weight on the side arm rests. DO NOT use

them in assisting the client on and off the table.

• DO NOT put excessive weight or pressure on the QuickLock™

Face Rest. Excessive pressure can cause premature failure of the

QuickLock™Face Rest. Do Not extend the dowels of the Face Rest

further than 3” from the table edge to ensure a stable connection.

• DO NOT store or place anything on the cabinet hood under the

backrest as this can cause damage to the top and or hood and will

void the warranty.

• Maximum Working Load Rating (client and accessories): 500 lbs.

(226 kg.)

• Every 3 months check nuts & bolts and physical connection points

for any loose parts. Tighten as needed.

• Maximum Shelf load weight: 225 lbs. (102 kg.)

READ AND

SAVE THESE

INSTRUCTIONS

CAUTIONS

GROUNDING & FOOT BATH CERTIFICATION

GROUND FAULT & GROUNDING INSTRUCTIONS

WARNINGS & SAFETY INSTRUCTIONS (CONTINUED)

GROUNDING INSTRUCTIONS

• The integral GFCI should be tested on a routine basis. To test the GFCI,

push the test button. The GFCI should interrupt power. Push the reset

button. Power should be restored. If the GFCI fails to operate in this

manner, DO NOT USE THE UNIT. Disconnect the unit and have the

problem corrected by a qualified service representative or an electrician

before using.

• This product must also be connected to a Ground Fault protected outlet

with the detector in the main circuit breaker box (not on the circuit).

(NOTE: GFCI ON THE TABLE ALONE IS NOT SUFFICIENT FOR

YOUR SAFETY.) The Ground fault detector in the main circuit box

should also be tested on a routine basis.

• This product is manufactured for use on a nominal 120-volt circuit for

North America and a nominal 220-volt circuit for use in Europe. The

plug has a grounding pin in a pattern that varies by country as shown

in the Product Identification section of this manual. Make sure that the

product is connected to an outlet having the same configuration as the plug.

No adapter should be used with this product.

• THIS PRODUCT MUST BE GROUNDED -Improper connection

of the equipment-grounding conductor can result in a risk of electric

shock. Check with a qualified electrician or service man if you are in

doubt as to whether the product is properly grounded. Do not modify

the plug provided with the product - if it will not fit the outlet, have a

proper outlet installed by a qualified electrician.

READ AND

SAVE THESE

INSTRUCTIONS

GROUNDING

INSTRUCTIONS

CAUTIONS

WHIRLPOOL FOOT BATH

The whirlpool foot bath provides excellent hydrotherapy, quiet operation

and the ability for quick, easy and certified cleanliness.

SANITATION CERTIFICATION: The National Sanitation Foundation (nsf.org)

has confirmed that the whirlpool foot bath can be completely cleaned and

disinfected, even if the system cleaning has been neglected.

PRODUCT DESCRIPTION

Backrest top

TABLE SPECIFICATIONS

 • LiftCapacity: 500lbs.(226kg.)

 • Weight: 200lbs.(91kg.)

 • ShippingWeight: 250lbs.(114kg.)

 • ShippingBoxDimensions:81”Lx37”Wx31”H

 • HeightRange: 25”-33”(64-84cm)

 • Width: 30”(76cm)

 • Length: 77”(195cm)

 • Top: ElectronicallyControlledBackrestTop

 • Base: MetalFrameBasewithshelfandelectricheightadjustment

 • Electronics: 1HandControl&1FootControl

 • Padding: 4”Aero·Cel™(standard),6”Aero·Cel™available

 • Upholstery: TerraTouch™(standard),UltraTouch™available

 • Shelf: 24”x37”(opening=113/4”x32”)

Forelectricalspecs,seeSpecificationsChart

* measurements are determined from floor to top of seat pad using standard padding; these measurements

can be affected by natural material variations in padding

 ** publishedweightmaydifferduetooptionschosen,naturalmaterialvariationsandpaddingdensity

PRODUCT DESCRIPTION

Storage shelf

PRODUCT DESCRIPTION

Hydraulic Lift

Columns (4)

Powder

Coated

Steel Base

Manicure

Arm rests (2)

PediBath

INSTALLATION

ASSEMBLY & INSTALLATION

INSTALLATION

The table comes completely assembled and ready to use. Plug the cord into

a functioning GFCI outlet that is rated for the table.

Arrange the power cord and foot switch so that they will not create a tripping

hazard. Place the controls in a safe location where they are convenient and

accessible. Keep the controls out of the way of all table mechanisms.

If your table was ordered with the optional faucet & drain, please review

typical installation instructions in document CSI-0077.

INSTALLATION

If Table Will Not Sit Flat on the Floor:

The table is equipped with Leveler Feet that adjust to level the table on

uneven floors. To adjust the Leveler Feet to suit common floor dif-

ferences you will need to use a 1

/2” open-end wrench or an adjustable

wrench. Adjust each leg individually in turn by adjusting the height of

each leveler foot until the unit rests level and steady. This adjustment

will not effect the function of the table.

LEVELING INSTRUCTIONS

The table weighs as much

as 200 lbs. DO NOT lift or

move the unit without using

proper safely procedures

or equipment. DO NOT turn

the table on its side for any

reason. To do so could

cause damage to the base

and will void the warranty.

There are no serviceable

items that require this action.

Never lift the table by grasp-

ing the table top as the

table top is not designed to

hold the weight of the base

and you could damage the

table.

IMPORTANT

1/2”Open-endWrench

When operating the table’s

controls be sure to observe

all cautions and warnings

given in the manual to pre-

vent injury to both operator

and client.

CAUTION

Andere Handbücher für Clodagh Libra

Inhaltsverzeichnis

Andere OAKWORKS Pediküre Spa Handbücher

OAKWORKS

OAKWORKS Clodagh Libra Bedienungsanleitung

Beliebte Pediküre Spa Handbücher anderer Marken

hadewe

hadewe Xantos-BT Bedienungsanleitung

Terraillon

Terraillon TONIC 2 Bedienungsanleitung

XENOX

XENOX Nail 35K Bedienungsanleitung

Continuum

Continuum Echo Bedienungsanleitung

DIR

DIR DRAGON Bedienungsanleitung

UFESA

UFESA BH5624 Bedienungsanleitung

Peter Bausch

Peter Bausch 0300 Bedienungsanleitung

Remington

Remington PFS-600 Bedienungsanleitung

hadewe

hadewe Veloria MD Bedienungsanleitung

j&a

j&a Cleo AX Bedienungsanleitung

European Touch

European Touch RINATO XL SPA Bedienungsanleitung

HoMedics

HoMedics BubbleBliss FB-30 Leitfaden

HoMedics

HoMedics JetSpa Elite FB-300 Leitfaden

HoMedics

HoMedics BubbleSpa BL-150 Leitfaden

Lexor

Lexor ELITE Bedienungsanleitung

Scarlett

Scarlett VitaSpa SC-CA304PS11 Bedienungsanleitung

Lexor

Lexor LIBERTE Bedienungsanleitung

DIR

DIR Gragon 5820 Bedienungsanleitung