Observint NB8 Bedienungsanleitung

1www.observint.com RS_NB8_CQ

181226

Installation

Before installation:

• Make sure that the device is in good condition and all the assembly parts are included.

• Check the specication of the products for the installation environment.

• Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.

• To avoid re or shock hazard, use only UL listed power supplies. Verify that the power supply will

provide the rated voltage and wattage for the camera. See the Specications section.

Step 1. Mounting the camera

A NB8 camera can be mounted directly to a wall or ceiling. The surface should support at least three times

the weight of the camera and junction box (if used). The LAN/power drop cable from the camera can be

routed either through mounting surface or through a cable channel in the mounting base.

• Mounting the camera directly to a wall or ceiling

Typical ceiling mounting

NOTE

If mounting the camera on a wall, ensure that the cable channel in the mounting base is down.

If mounting the camera on a ceiling, orient the mounting base so that the cable channel is pointing

away from any source of water, dust, and other contaminates.

1. Using the drill template provided, mark the location of the screws that anchor the mounting base

to the mounting surface. See the note above. If you are routing the drop cable through mounting

surface, also mark the position of the hole for the drop cable.

2. Drill holes for the screws that anchor the base to the mounting surface. The mounting hardware

provided is appropriate for most surfaces. However, depending on the surface materials, more

appropriate fasteners may be required.

3. If routing the drop cable through the mounting surface, drill a 5/8” hole in the middle of the drill

template.

4. Route the drop cable through the hole in the mounting surface, or through the cable channel in the

mounting base, then attach the camera assembly to the surface using the appropriate fasteners.

5. Connect the network LAN and power extension cables to the camera drop cables:

a. Connect the Ethernet LAN cable to the camera LAN drop cable. Protect the connection from

moisture and other contamination, if necessary. A Weatherproof Ethernet Fitting is provided.

Installation instructions for the tting are included later in this document.

Network drop cable

from camera Network cable from

router or switch

Weatherproof Ethernet Fitting installed

WARNING

Drop cable connectors are not waterproof. Failure of the power or Ethernet connector

due to moisture or another contaminant is considered an installation error,

which voids the warranty. If installing this camera in a location such as an

overhang, shop, garage, kitchen, etc. where high humidity or dust is present,

seal these connections adequately.

b. If the camera is not powered using PoE (Power over Ethernet injector), connect the 12 Vdc

power cable to the camera drop cable. The polarity of the drop cable connector is shown in

the drop cable photo above.

NB8 8MP PIR Bullet IP Camera

Quick Installation Guide

The NB8 bullet camera include passive IR (PIR) technology for better motion sensing. It features a high

resolution, low image distortion and low noise features which makes it suitable for surveillance and image

processing systems.

Features

• 8 MP 3840 (H) × 2160 (V) pixel resolution

• H.265 / H.264 video compression

• 2.8 mm lens

• Flip, Rotation and Corridor modes

• 95 feet IR range

• 23 ft PIR range with 120° detection angle

• BLC, ROI and Privacy Mask

• 3D-DNR, D-WDR and IR cut lter

• IP66 weatherproof

Cable channel

Camera body

Mounting base

Lens

PIR sensor

Adjustable

mounting

bracket

12 Vdc Power connector

Ethernet connector -

PoE capable

Camera drop cables

What’s in the box

• Camera assembly

• Mounting hardware

• Waterproof Ethernet connector

• This instruction guide

• Drill template

Tools you need

To install the camera, you will need:

• 12 Vdc power source or Ethernet PoE injector. See Specications for wattage requirement.

• Tools and additional fasteners (may be required) for mounting the camera

• Ethernet drop cable

• 12 Vdc power extension cable (if powering with 12 Vdc supply)

2www.observint.com

CAUTION

Do not apply power to the camera at this time. Before applying power to the camera, ensure that

the polarity is correct. An incorrect connection may cause a malfunction and can damage the

camera.

6. For outdoor installations, seal holes drilled in the mounting surface to block moisture and other

contaminants, if necessary.

7. Secure the camera to the mounting surface using appropriate screws.

8. Apply power to the camera through the 12 Vdc power cable or PoE injector, as congured.

Step 2. Using the Device Configuration Tool software

NOTE: Skip this Step if you are adding your camera directly to the Ethernet connectors on the backpanel if an NVR.

Installation

The Device Conguration Tool is a PC-based network utility for discovery of NTx or NBx cameras for your

N-Series recorder. It provides an easy way to congure the camera’s network settings and reset the camera.

It can be installed on a Microsoft® Windows® (Windows 7 or newer) operating system that has access to

the network where your the cameras are installed. The Device Conguration Tool is available from your

vendor.

1. Acquire the Device Conguration Tool from your vendor. At the time when this document was

published, the le is named: Device Cong Tool_<version>.exe.

2. Run the .exe le on a Windows computer that is connected to the LAN where your cameras are

installed. Follow the on-screen instructions to complete the installation. You may have to open

ports in your rewall. The software automatically opens after it is installed and then searches for

cameras on the LAN. See below.

Click here to view network settings

Modify network settings

Modify the network settings of the camera you are installing to avoid IP address conicts on the LAN. Verify

that the your new settings will be compatible with other devices on the network before continuing. Consult

with your network administrator for specic recommendations, if necessary.

3. Click the entry in the search results list for the camera you are installing. The frame at the bottom of

the window shows User Info (UserName and Password) and Device Info (network settings).

4. Enter the new and compatible network settings in the Device Info eld (see below). Here, the IP

address was changed to 192.168.0.68, and the Gateway was changed to 192.168.0.1.

5. Click Modify, and then slide the Shift Bar to the right. The Status of the modify operation is

shown in the right-most column.

Modify status

Shift bar

6. Slide the Shift Bar to the left to see the new settings in the Search list.

Click here to login

Step 3. Perform the initial setup of the camera

NOTE: Skip this Step if you are adding your camera directly to the Ethernet connectors on the backpanel if an NVR.

1. To log into the camera and setup a password, click on the IP address of the camera in the list you

want to log into (see above). If SurveillancePlugin was not previously installed on your computer, the

following window will appear. You must install the plugin to access the camera.

2. In the screen above, click the download hyperlink.

3. In the following window, click Run in the footer menu, and then close your browser.

4. Follow the on-screen instructions to complete the installation o SurveillancePlugin.exe.

5. Return to the Device Conguration Tool menu, and then click on the IP address of the camera

you want to log into.

6. If the follow screen appears, click (select) Allow in the footer query.

7. Next, the browser will appear with a Password popup window. Use this feature to setup a unique

password for your camera. Enter a password in the Password and Conrm elds that indicates a

High security level as shown below, and then click OK. Copy the new password for the camera and

save it in a safe place.

8. In the Login screen shown below using the new password you created previously.

Following a successful login, the camera live view window will appear. Notice that SubStream is

shown by default. Click MainStream to see a better image.

Click here to LogoutScreen selectLive view imageStream select

Step 4. Using the NVR Live View screen - add camera

NOTE: Skip this Step if you are adding your camera to an IP network.

If you are adding your camera directly to the NVR backpanel Ethernet connectors, use this step.

Click to add camera

1. To add a camera to a frame, click the +icon in the upper right corner.

2. In the Quick Add menu that opens, a list of cameras that can be added appears at the top. Click on

the one you want to add to the viewing frame.

3. Check the parameters in the menu to ensure they are correct (see above), and then click the Add

button. Video from the camera will appear in the viewing frame.

Status Icons

Refer to the User Manual for your NVR for additional information about using your camera.

Camera adjustments

1. Apply power to the camera.

2. Verify that video from the camera can be seen on the monitor.

3. While observing video from the camera, loosen the mounting bracket pan lock screw, and tilt and

rotation adjustment lock screws, point the camera at your surveillance target, and then tighten

adjustment lock screws to hold the camera in position.

0° ~ 90°

0° ~ 360°

Rotation: Use for horizon

line adjustment

Pan: Use

for pan

adjustment

Tilt: Use for

elevation

adjustment

Mounting bracket adjustment

Step 5. Additional Setup procedures

Refer to the User Manual for your camera for procedures to customize your camera for your surveillance

application.

Specications

Model NB8

Resolution 8 MP: 3840 (H) × 2160 (V)

Image Sensor 1/2.3” Progressive CMOS

Min. Illumination Color 0.1 lux @ F1.2 (AGC ON); B/W 0 lux @ IR ON

Shutter 1/5 ~ 1/20000s

Slow shutter Supported

Lens 2.8 mm

F No. F 2.0 ±5%

Day & Night IR cut lter with auto switch (Day/Night/Auto/Schedule)

Digital noise reduction: 3D DNR

WDR Digital

Video Compression H.265 / H.264

Video bit rate 8 Kbps ~ 8 Mbps

Triple Stream Yes

Resolution Main Stream: 8 MP (3840 × 2160), 5 MP (3072 × 1728) (5292 × 1944), 4 MP (2592 × 1520),

3 MP (2304 × 1296), 1080P (1920 × 1080), 720P (1280 × 720),

Sub Steam 1080P (1920 × 1080), 720P (1280 × 720), VGA (640 × 480), QVGA (320 × 240)

Mobile Stream VGA (640 × 480), QVGA (320 × 240)

Image Settings: Flip, Rotation, Corridor mode, Saturation, Brightness, Contrast, Hue, Sharpness adjustable

SD card slot Yes, for microSD up to 128GB (For cameras provided individually only. Not for cameras in kits.)

BLC Supported

ROI Supported

Privacy Mask Supported

Video Analytics NA

Protocols TCP/IP, HTTP, DHCP, DNS, DDNS, RTP/RTSP, PPPoE, SMTP, NTP, UPnP, SNMP, HTTPS, FTP

System Compatibility ONVIF (Ver 2.6, Prole S, Prole G)

Interface RJ45 10M / 100M Ethernet interface × 1

Led 18 pcs (SMD)

IR Range Up to 95 ft (30 m)

Alarm Trigger No

Audio No

Video Output: No

Reset Button No

PoE Yes

Water Proof IP 66

Power Supply 12 Vdc / PoE

Consumption ≤ 7 W

Weight .77 lb (349 g) approx.

Storage Temperature -22° + 140°F (-30° + 60° C)

Operating Temperature -22° + 131° F (-30° + 55° C)

PIR Detection Angle 120°

PIR Detection Distance 23 ft (7 m)

Cleaning

Clean the camera dome with an approved glass cleaning solution and a lint free cloth.

• Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub

the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a

soft cloth. Do not use benzene, thinner or other chemical products on the camera assembly; these

may dissolve the paint and promote damage of the surfaces.

• Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.

These may cause damage to the surface over time.

Using the Waterproof Ethernet Fitting

Install the Waterproof Ethernet Fitting on the Ethernet cable end at the camera when moisture or

contamination exists in the area near the camera. The tting includes several parts that must be installed in

a specic order. To install the tting:

1. Place the rubber O-ring over the camera drop cable end cap.

Push the O-ring up to the connector cap.

2. If the network cable from the switch or router has a connector

on the end, cut o the connector.

3. Place the Lock Nut onto the network cable from the router

or switch as shown in the drawing to the right. The inside

threads must be toward the camera end.

4. Place the rubber basket onto the network cable above the lock

nut as shown.

5. Place the end cap onto the network cable above the rubber

gasket as shown. The ngered end must be toward the router

or switch.

6. Install an RJ-45 connector onto the network cable.

7. Plug the RJ-45 connector with the network cable into the

camera network drop cable.

8. Fit the end cap on the network cable onto the camera drop

cable end cap. Rotate the network cable end cap to lock it in

place.

9. Push the rubber gasket fully into the end of the network cable

end cap.

10. Screw the lock nut onto the network cable end cap until it is

fully seated.

Network drop

cable from

camera

Network cable from

router or switch

Ethernet Fitting installed

Waterproof Ethernet Fitting assembled and connected

Drop cable

end cap

Network drop

cable from

camera

Rubber

O-ring

seal

RJ-45

connector

End cap

Rubber

gasket

Network

cable

from

router or

switch

Lock nut

Inhaltsverzeichnis

Andere Observint IP-Kamera Handbücher

Observint

Observint BLK-CPD227VH Bedienungsanleitung

Beliebte IP-Kamera Handbücher anderer Marken

FLIR

FLIR Exx series Bedienungsanleitung

Avigilon

Avigilon H4A-BO1-IR Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWCA-C128-64 Bedienungsanleitung

ShareTech

ShareTech AV1 Bedienungsanleitung

Ezviz

Ezviz C6C Bedienungsanleitung

Melchioni

Melchioni UCAM 2015 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ESD-4630 Bedienungsanleitung

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Bedienungsanleitung

Mitel

Mitel 6800i Series Service-Handbuch

Vitek

Vitek VTC-IR403-212NP Bedienungsanleitung

THOMSON

THOMSON DSC - 323W Bedienungsanleitung

AVer

AVer FB2027 Bedienungsanleitung

ENFORCER

ENFORCER EV-T5105-N2SQ Bedienungsanleitung

Wansview

Wansview NC543 Bedienungsanleitung

Eneo

Eneo MCB-64A0003M0A Bedienungsanleitung

deView electronics

deView electronics CBDNI36F Bedienungsanleitung

Swann

Swann SwannEye Bedienungsanleitung

LevelOne

LevelOne IP CamSecure Bedienungsanleitung