OBSIDIAN CONTROL SYSTEMS Netron RDM10 Bedienungsanleitung

images, and instructions herein are subject to change without notice. Obsidian Control Systems logo

and identifying product names and numbers herein are trademarks of ADJ PRODUCTS LLC. Copyright

protection claimed includes all forms and matters of copyrightable materials and information now

allowed by statutory or judicial law or hereinafter granted. Product names used in this document may

be trademarks or registered trademarks of their respective companies and are hereby acknowledged.

All non – ADJ brands and product names are trademarks or registered trademarks of their respective

companies.

OBSIDIAN CONTROL SYSTEMS and all affiliated companies hereby disclaim any and all liabilities for

property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect

economic loss associated with the use or reliance of any information contained within this document,

and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and

operation of this product.

OBSIDIAN CONTROL SYSTEMS B.V.

Junostraat 2 | 6468 EW Kerkrade, The Netherlands

+31 45 546 85 66

Art-Net

This device incorporates Art-Net™, Designed by and Copyright Artistic License Holdings Ltd

Document Version: An updated version of this document may be available online. Please check

www.obsidiancontrol.com for the latest revision/update of this document before beginning installation

and use.

Date

Document Version

Note

01/29/20

1.0

INITIAL RELEASE

CONTENTS

GENERAL INFORMATION

OVERVIEW

CONNECTIONS

MENU:

NAVIGATION

HOME SCREEN

PRESETS

DMX INPUTS

DMX PORTS

CUES

VIEW AND TEST

IP ADDRESS

SYSTEM

INFORMATION

WEB REMOTE CONFIGURATION

WEB REMOTE: HOMEPAGE

FIRMWARE UPDATES

GENERAL INFORMATION

INTRODUCTION

Please read and understand the instructions in this manual carefully and thoroughly before

attempting to operate this device. These instructions contain important safety and use

information.

CUSTOMER SUPPORT

Contact your local Obsidian Controls Systems dealer or distributor for any product related

service and support needs. Also visit forums.obsidiancontrol.com with questions, comments

or suggestions.

OBSIDIAN CONTROL SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET

+31 45 546 85 63 | [email protected]

OBSIDIAN CONTROL SERVICE USA – Monday – Friday 08:30 to 17:00 PST

(866) 245 – 6726 | [email protected]

OVERVIEW

KEY FEATURES

The NETRON RDM10 is a first of its kind hybrid splitter. Dual DMX input, 10 port RDM

Splitter, Merger and EthernetDMX Gateway are unified into the RDM10, with an advanced

feature set to cover a wide variety of applications. 99 internal cues, factory and user presets,

plus external contact closures provide a unique combination of multiple devices to solve

many required tasks in one powerful unit.

- 2x Input, 10x Output ports

- RDM Splitter, HTP / LTP DMX Merge

- 2 Universe sACN and Artnet to DMX conversion

- Premade NETRON presets for instant setup

- 10 User Presets

- 99 Cues with Fade Time, Hold Time and Cue linking

- External contact closures to trigger cues and preset recall

- DMX Monitor

- DMX and Ethernet Test Generator

ETHERNET CONNECTION

The RDM10 provides two Gigabit RJ45 connections for data input. One port supports POE

802.3af power input and is marked with POE on the back of the device. Both ports are

connected to an internal highspeed network switch, allowing daisy chaining of multiple

devices. To avoid synchronization delays it is not recommended to chain more than 10

devices together. The ports are auto-crossing, eliminating the need for RJ45 crossover

cables.

SOFTWARE

The software for RDM10 is available from the support website http://obsidiancontrol.com.

Update your device to the latest software, and periodically check the website for updates.

CONNECTIONS

DMX CONNECTIONS

All DMX Output connections are 5pin female XLR; however, the pin – out on all sockets is pin 1 to

shield, pin 2 to cold ( – ), and pin 3 to hot (+). Pins 4 and 5 are not used.

Carefully connect DMX cables to the respective ports.

To prevent damaging the DMX ports, provide strain relief and support. Avoid connecting FOH

Snakes to the ports directly.

Connection

Com

Data -

Data +

Not connected

ETHERNET DATA CONNECTION

The Ethernet cable is connected on the back of the gateway into the port labeled A or B. Devices

can be daisy chained, but it is recommended not to exceed 10 Netron devices in one chain.

Because these devices use locking RJ45 connectors, and the use of locking RJ45 ethernet cables

is recommended, any RJ45 connector is suitable.

To connect multiple devices to an EtherDMX Source, an Ethernet switch is required to split the data

into the desired number of streams.

The Ethernet connection is also used to connect a computer to the Netron device for remote

configuration via a web browser. To access the web interface, simply enter the IP address shown

in the display in any web browser connected to the device. Information about the web access can

be found in the manual.

CONNECTIONS: FRONT & REAR PANELS

FRONT CONNECTIONS

- (10) 5pin DMX/RDM optically isolated ports

- Full color OLED display

- Encoder with Push-to-Select / Exit Button

DMX PORTS STATUS INDICATOR LEDs

Ports

LED Color

Solid

Slow Blink

Flashing/Strobing

RJ45

LINK Green

Link established

RJ45

ACT Yellow

Network Traffic

DMX

Red

Error

DMX

White

active RDM communication

DMX

Blue

Assigned to A

No DMX Signal

DMX

Amber

Assigned to B

No DMX Signal

DMX

Cyan

Assigned to Merger

No DMX Signal

DMX

Purple

Set to Send Static DMX Value

The LEDs are dimmable from the System – Display menu, and can be turned off completely

if desired.

REAR CONNECTIONS

- (2) 5pin DMX Input

- (2) 5pin DMX Through

- (2) RJ45 network connections (1x POE)

- (10) Contact Closures (Terminal Block)

- Power In/Thru

Turn to scroll,

push-to-select

OLED Display

(2) 5-Pin

DMX Input

Menu return

button

Power Out

Power In

Fuse

RJ45 Network

connection w/POE

DMX Port Status

Indicator LED

Contact Closures

(Terminal Block)

(10) 5-Pin Opto-Isolated

DMX Outputs

5pin DMX Through

5pin DMX In

Terminate button

(120 Ohm) for DMX In

RJ45 Network

connection

CONNECTIONS: CONTACT CLOSURES

DO NOT APPLY VOLTAGE TO THE CONTACT! DOING SO WILL DAMAGE THE

INPUT AND IS NOT COVERED UNDER WARRANTY.

The RDM10 is shipped with two terminal blocks that connect to the back ports. Lost or missing blocks

can be purchased from authorized Obsidian Dealers.

10 Inputs are provided that can be mapped to various functions of the

RDM10. The inputs are simple dry contact closures and are provided

in ten pairs of trigger and ground connections.

MENU: NAVIGATION

The Netron RDM10 uses a small OLED display for feedback and setup. The encoder dials up

and down through the menu, a push of the encoder selects an item or saves an entry. Revert

back to a previous menu or cancel an entry with a single push of the back arrow.

Wheel Right

Scroll down in menu list / increase values

Wheel Left

Scroll up in menu list / decrease values

Wheel Push

Enter Menu, Select menu item, go down one level in menu, confirm

values.

Back Arrow

Go up one level in menu tree, cancel change of values, hold for 2

seconds to return to home screen

As you scroll up or down the menu, the arrows indicate that more items are available above or below

that which is displayed, and only show when needed.

MENU: HOME SCREEN

This is the default screen, which provides quick status feedback and indicates IP and DMX traffic. Turn the

encoder wheel to the right to show Page 2 (clockwise), or turn it left to show Page 1 (counterclockwise). The

page defaults to Page 1 after a timeout (the same timeout duration as with the menu).

Page 1

The home page shows the A and B input status. Valid traffic and the source are indicated with a full colored box.

The current merge mode and active source are displayed in the bottom half for immediate overview of the merge

activity. Certain Merge statuses like an active Backup will yield a red background, indicating that the unit

triggered its backup source.

Page 2

Ports: The port numbers show the assigned input source. A and B source assignments are displayed on top.

IP Address: shows the

current IP address of the

device. Use this address

inside a web browser for

remote access.

IP A / B: White text with a check mark indicates if a network port is

connected. Red indicated the port is not connected.

Andere Handbücher für Netron RDM10

Inhaltsverzeichnis

Andere OBSIDIAN CONTROL SYSTEMS Medienkonverter Handbücher

OBSIDIAN CONTROL SYSTEMS

OBSIDIAN CONTROL SYSTEMS Netron RDM6XL Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung