Oce VarioPrint 6000 MICR series Bedienungsanleitung
-
o
Océ
VarioPrint® 6000
Ultra Line
Experience ultra speed
User manual
Safety information
Copyright
© 2009-2011, Océ
All rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted
in any form or by any means without written permission from Océ.
Océ makes no representation or warranties with respect to the contents hereof and specifi-
cally disclaims any implied warranties of merchantability or fitness for any particular purpose.
Furthermore, Océ reserves the right to revise this publication and to make changes from
time to time in the content hereof without obligation to notify any person of such revision
or changes.
Edition: 07-2011
Contents
Chapter 1
Safety information..............................................................................................5
Instructions for safe use............................................................................6
Chapter 2
Regulation notices............................................................................................11
Regulation notices (country dependent)................................................12
Chapter 3
General information.........................................................................................17
Caution labels and notations...................................................................18
Chapter 4
Safety information - iXDP................................................................................21
Instructions for safe use - iXDP (integrated eXchangeable Die Punch).22
Appendix A
Miscellaneous....................................................................................................27
Online support for your product.............................................................28
3
Contents
4
Contents
Chapter 1
Safety information
Instructions for safe use
Introduction
All the products have been tested in accordance with the strictest international safety
standards. Please read the following sections before you connect the machine to the
power supply. These sections contain important information with regard to the user
safety and the prevention of equipment problems. Make sure that you observe the safety
rules hereinafter. This helps to assure that you can work with the product safely. Make
sure that you observe all the precautions mentioned below.
Note:
Some parts of the contents of this section may not be applicable to your product.
Note:
Please refer to the corresponding Safety Data Sheets for specific safety information. You
can download the Safety Data Sheets from the support site of your product at
http://global.oce.com/support/.
Disassembly and Modification
Warning
•Do not remove covers and panels that are fixed to the machine. Some machines have
a high-voltage component or a laser beam source inside that could cause an electric
shock or blindness
•Do not modify this machine, since this could cause fire, electric shock, or breakdown.
If the machine contains a laser, the laser beam source could cause blindness.
Caution
•Do not carry out maintenance activities on components and maintenance materials
other than the components and materials that are mentioned in the user manual.
•Do not place any liquids on the machine.
•Do not open any door while the machine starts up or runs, unless the operator panel
displays a message asking you to open one or more doors.
•Only use maintenance materials or other materials for their intended purpose.
•To avoid any risk, only properly qualified and trained service technicians are allowed
to modify the machine.
•Do not bridge any mechanical or electrical circuit breakers.
Note
•Keep maintenance materials away from children.
Chapter 1 - Safety information6
Instructions for safe use
Power Cord
Warning
•Do not scratch, abrade, heat, twist, bend, place a heavy object on or cause any other
damage to the power cord. The use of a damaged power cord (exposed core wire,
broken wire, for example) could result in a fire or breakdown. If you discover any of
these conditions, turn OFF the power switch immediately and unplug the power cord
from the power outlet. Then call your authorized service representative.
•Do not use an extension cord to connect to the machine.
•Only use the mains connector cable that was supplied with the machine.
Power Supply
Warning
•Insert the power plug directly into a wall socket that has the same configuration as
the plug. The use of adapter leads can result in an inadequate power supply. If a suitable
wall outlet is not available, ask a qualified electrician to carry out the installation.
•Do not connect the machine to mains voltage that differs from the value stated on
the power marking label.
•Do not use a multiple outlet adapter or an extension lead. Contact your authorized
service representative if an extension lead is required.
Caution
•Consult your authorized service representative before you connect other equipment
to the same wall outlet.
Note
•If connection to a different mains voltage is required, contact your authorized service
representative.
•The input interface module is accessible at the front of the machine. This module
contains a power outlet that is intended for service purposes only. Do not connect
any electrical device to this power outlet.
Power plug
•For machines that are connected via a wall socket: Place the machine close to a wall
socket that is easily accessible. The power plug is intended to serve as a disconnect
device.
Grounding
Warning
•Connect the power cord to an electrical outlet (wall socket) that is equipped with a
grounding terminal.
•This equipment was not designed for connection to an IT power system. (An IT
power system is a voltage network in which the neutral wire is not grounded).
Chapter 1 - Safety information 7
Instructions for safe use
Installation
Warning
•Ensure that the machine is placed on a level, horizontal surface of sufficient strength.
•Do not place this machine on an unstable or tilted bench.
•Do not place this machine in a location that is subject to lots of vibrations and shocks.
•Do not use flammable sprays, liquids, or gases near this product, since this could cause
a fire.
Note
•It is recommended that you connect only those copy-control products (or other
products) which meet the (inter)national product safety and radio frequency interfer-
ence standards. Only use an attachment cable as specified by the manufacturer.
Ventilation
•The machine can produce odors of exhaust air when you:
- use this machine in a poorly ventilated room for a long time
- produce large amounts of copies or print
Therefore, make sure that you ventilate this room well.
•Do not block the machine's ventilation openings.
•Do not place the machine in rooms which are too small and insufficiently ventilated.
See the Product Safety Data Sheet of the machine for the ventilation requirements.
•Be sure to allow a clearance of 300 mm/11.81 inch or more at the back of this machine
for the ventilation duct.
Solving Problems
Warning
•When a piece of metal, water or any other similar foreign matter gets inside the ma-
chine, immediately turn OFF the power switch and unplug the power cord from the
power outlet. Then call your authorized service representative.
•Stop using the machine immediately if it becomes excessively hot, emits smoke, or
produces unusual odors or noises. Turn OFF the power switch immediately and unplug
the power cord from the power outlet. Then call your authorized service representative.
Caution
•Stop using the machine if it is dropped or a cover is damaged. Turn OFF the power
switch immediately and unplug the power cord from the power outlet. Then call your
authorized service representative.
•Some areas inside the machine may become hot. Touching these areas could cause
burns. When you check for malfunctions inside the machine such as a paper misfeed,
do not touch the locations which are labeled "Caution HOT". You can find these labels
around the fusing unit, for example.
Chapter 1 - Safety information8
Instructions for safe use
•LCD display. Do not rub, press, or touch the display surface with hard material, be-
cause the polarizer at the surface can be easily scratched. The LCD module consists
of glass. Therefore, the LCD module can be damaged when you drop, pinch strongly,
or punch the module. If glass breaks, be careful not to injure yourself on the glass
fragments. Call Océ Customer Service.
Consumables, Supplies and Maintenance Materials
Warning
•Do not throw toner cartridges or toner into an open flame.
Caution
•Do not leave a toner unit or drum unit within reach of children.
•Always use the materials recommended by the manufacturer that are developed for
this machine. Materials not approved by the manufacturer may result in damage to
your machine.
Moving the Machine
Caution
•Make sure that you disconnect the power cord and other cables before you move the
machine.
•Make sure that you check the documentation for the space requirements before you
move the machine.
Holidays
Caution
•Unplug the machine if you will be using it for a long period of time.
Key operator maintenance
A part of the key operator maintenance tasks can be performed in the hot area of the
machine. These are:
•Replace the spiral cleaner
•Replace the TTF belt
•Cutting the sheet cleaner
•Clean the glue cleaners
•Solve paper jams.
There are two ways to protect your hands against heat:
•Use the heat-resistant gloves that are supplied with the printer, or
•Work on the machine after it has cooled down. If you do not have a 24-hour work
shift, the printer will provide you with a schedule for replacing parts in the morning
before the machine warms up.
Chapter 1 - Safety information 9
Instructions for safe use
Chapter 1 - Safety information10
Instructions for safe use
Andere Handbücher für VarioPrint 6000 MICR series
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Oce Multifunktionsdrucker Handbücher
Oce
Oce OP1030 Bedienungsanleitung
Oce
Oce CM4520 Bedienungsanleitung
Oce
Oce CS175 Phase 3 Bedienungsanleitung
Oce
Oce VarioPrint 2062 NC Bedienungsanleitung
Oce
Oce cm5520 Bedienungsanleitung
Oce
Oce VarioLink 2222c Bedienungsanleitung
Oce
Oce CS655 Pro Gebrauchs- und Pflegehandbuch
Oce
Oce Color System 200 Bedienungsanleitung
Oce
Oce ColorWave 300 Bedienungsanleitung
Oce
Oce CM4520 Bedienungsanleitung
Oce
Oce VarioLink 4522c Bedienungsanleitung
Oce
Oce im7520 Bedienungsanleitung
Oce
Oce im5530 Montage- und Wartungsanleitung
Oce
Oce im7520 Bedienungsanleitung
Oce
Oce FX3000 SERIES Bedienungsanleitung
Oce
Oce fx2080 Bedienungsanleitung
Oce
Oce VarioLink 5022 Bedienungsanleitung
Oce
Oce OP1030 Bedienungsanleitung
Oce
Oce cx2100 Bedienungsanleitung
Oce
Oce VarioLink 4522c Bedienungsanleitung
Beliebte Multifunktionsdrucker Handbücher anderer Marken
Triumph Adler
Triumph Adler DC 2016 Handbuch
Epson
Epson WorkForce WF-2510 Benutzerhandbuch
Epson
Epson Stylus Scan 2000 Installations- und Betriebshandbuch
Epson
Epson PictureMate Snap PM 240 Bedienungsanleitung
Konica Minolta
Konica Minolta bizhub C35 Bedienungsanleitung
Brother
Brother MFC-J430w Bedienungsanleitung
