OKIDATA B6300 Montage- und Wartungsanleitung
AbsoluteCOLOR • AbsoluteBLACK • UniDrums • UniRollers • UniParts • UniCoatings
OKIDATA®B6300 REMANUFACTURING INSTRUCTIONS
AbsoluteCOLOR®• AbsoluteBLACK®• UniDrums • UniRollers • UniParts • UniCoatings
OKIDATA B6300 PRINTER
TONER CARTRIDGE
WITH OEM CHIP SHOWN
REMOVING THE CHIP
1. Using a small screwdriver, push in one of
the tabs located beneath the base to
release the chip that is held in place.
2. The chip can now be lifted from the top
or pushed out through the tab holes
beneath the chip base.
3. Chip removed with tab holes shown. It
will be replaced later with a new
Smartchip.
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2005 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4574-3706
+54-11-4574-3706
www.uninetimaging.com
UNINET IMAGING INC. •OKIDATA®B6300 REMANUFACTURING INSTRUCTIONS
4. Remove the shutter-door arm from the
slot on the gear-side of the toner cartridge
as shown.
5. Using a hook tool, remove the shutter-
door arm on the gearless side. Remember
the spring position for re-installation.
6. Remove the shutter-door and set it
aside.
ARM
ARM
SPRING
7. Remove the plastic pin on one end by
first drilling a hole in the center of it. This
will make it more accessible.
8. Use a 2.4 mm screwdriver to turn the pin
to the “release” setting (turn counter-clock-
wise sensitively until it stops).
9. Use a 2-angle hook to access and pull
the pin from the hole.
10. Remove the plastic pin on the opposite
end by drilling a hole in the center.
11. Turn the pin counter-clockwise to the
“release” setting as usual.
12. Pull the pin out through the hole.
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2005 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4574-3706
+54-11-4574-3706
www.uninetimaging.com
UNINET IMAGING INC. •OKIDATA®B6300 REMANUFACTURING INSTRUCTIONS
14. Lift evenly to separate the drum unit
from the cartridge.
13. Use a hook tool to release the spring
from the gear-less side.
15. Drum unit removed.
16. You are now ready to disassemble the
drum unit.
17. Remove the top screw of the drum gear
holder.
18. Remove the bottom screw of the drum
gear holder.
19. Remove the drum gear holder by
pulling it out.
20. Remove the two drum pin screws on
the other side.
21. Remove the drum pin by pulling it out.
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2005 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4574-3706
+54-11-4574-3706
www.uninetimaging.com
UNINET IMAGING INC. •OKIDATA®B6300 REMANUFACTURING INSTRUCTIONS
22. Carefully remove the drum. 23. You are now ready to remove the PCR. 24. Remove the PCR by un-clipping it from
the white and black holders.
25. Remove the wiper blade by unscrewing the two gold-colored screws at each end that
hold it in place as shown.
26. Lift the wiper blade evenly from the
waste hopper.
28. Use air pressure to blow out any
remaining toner.
27. You are now ready to clean the wiper
blade and waste hopper.
29. Once clean, you are now ready to
reassemble t he wiper blade.
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2005 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4574-3706
+54-11-4574-3706
www.uninetimaging.com
UNINET IMAGING INC. •OKIDATA®B6300 REMANUFACTURING INSTRUCTIONS
30. Reinstall the wiper blade back into position with the two gold-colored screws as shown. 31. Reinsert the PCR into the clips by using
slight force.
36. Remove the end-cap on the gear-side of the toner cartridge by first removing two gold-
colored screws as shown.
35. You are now ready to disassemble the
toner cartridge
33. Reinstall the remaining drum holder on
the opposite side.
32. Reinsert the OPC gear side first. 34. Line up the drum pin and screw back
into place.
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2005 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4574-3706
+54-11-4574-3706
www.uninetimaging.com
UNINET IMAGING INC. •OKIDATA®B6300 REMANUFACTURING INSTRUCTIONS
37. The end-cap should then slide out. 38. Remove all gears from the cartridge as shown in the following photos.
These gears are designed to fit one way, so reinstalling won’t become too difficult. 39. Unlock the MAG roller by lifting the
lever up as shown.
41. Continue with the other side until the
MAG is completely removed.
40. When the lever has been flipped up, lift
that side of the roller first.
42. Now you are ready to remove the
Doctor Blade.
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2005 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4574-3706
+54-11-4574-3706
www.uninetimaging.com
UNINET IMAGING INC. •OKIDATA®B6300 REMANUFACTURING INSTRUCTIONS
43. Unscrew the two gold-colored screws that hold the the Doctor
Blade in place as shown.
44. Doctor Blade removed.
45. Using a pair of needle-nose pliers, remove the two toner fill plugs located on the gear
side.
46. Empty the toner before removing the hopper.
47. REMOVING THE TONER HOPPER
Remove all four corner screws (as shown in
the following photos) that hold the toner
hopper and cartridge together.
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2005 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4574-3706
+54-11-4574-3706
www.uninetimaging.com
UNINET IMAGING INC. •OKIDATA®B6300 REMANUFACTURING INSTRUCTIONS
49. These foam seals surround holes
where toner passes through to the develop-
er roller. Residual toner can build up in
these areas, so it is important to clean
thoroughly before reinstalling the hopper.
48. Toner hopper removed. Note the two
foam seals located at the bottom of the
hopper.
NOTES:
50. Clean the hopper and toner cartridge
using compressed air or a vacuum. Refill,
and reassemble the cartridge following the
previous steps in reverse.
NOTE: A new Smartchip must be fitted
after reassembly of the toner cartridge.
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2005 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. Uninet Imaging does not guarantee or warrant downloaded information.
USA
+310-280-9620
+310-838-7294
Ph:
Fx:
JAPAN
+81-3-44-55-2789
+310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4574-3706
+54-11-4574-3706
www.uninetimaging.com
Andere OKIDATA Drucker Handbücher
OKIDATA
OKIDATA Pacemark 3410 Bedienungsanleitung
OKIDATA
OKIDATA OL400 Bedienungsanleitung
OKIDATA
OKIDATA OKIMATE 10 Bedienungsanleitung
OKIDATA
OKIDATA MICROLINE 320 Bedienungsanleitung
OKIDATA
OKIDATA Okipage 16n Bedienungsanleitung
OKIDATA
OKIDATA OL830 Bedienungsanleitung
OKIDATA
OKIDATA OKIPAGE 10ex Bedienungsanleitung
OKIDATA
OKIDATA OKIPAGE 8c Bedienungsanleitung
OKIDATA
OKIDATA OL400e Series Bedienungsanleitung
OKIDATA
OKIDATA Pacemark 3410 Anleitung zur Verwendung
OKIDATA
OKIDATA MICROLINE 320 Bedienungsanleitung
OKIDATA
OKIDATA Pacemark 3410 Bedienungsanleitung
OKIDATA
OKIDATA MICROLINE ML590 Bedienungsanleitung
OKIDATA
OKIDATA DOC-IT Series Bedienungsanleitung
OKIDATA
OKIDATA ML1120 Bedienungsanleitung
OKIDATA
OKIDATA ML380 Bedienungsanleitung
OKIDATA
OKIDATA ML172 Series Bedienungsanleitung
OKIDATA
OKIDATA ML393Plus Bedienungsanleitung
OKIDATA
OKIDATA C 9000 Montage- und Wartungsanleitung
OKIDATA
OKIDATA MC873 Bedienungsanleitung
