Olympus FR-WR Bedienungsanleitung

FR-WR

取扱説明書

INSTRUCTIONS

MODE D’EMPLOI

INSTRUCCIONES

BEDIENUNGSANLEITUNG

사용설명서

CHT 68

คําแนะนําการใชงาน

CÁC HƯỚNG DẪN

Model No.: IM013

Thank you for purchasing this Olympus product.

To ensure your safety, please read this instruction manual carefully before use.

In addition, please keep the manual handy for future reference.

Be sure to read the instruction manuals for the ﬂash and the wireless commander

as well.

If you use the product outside the country or region of purchase, you may violate

local regulations. Olympus accepts no liability in this case.

Checking the Contents of the Package

Wireless radiowave receiver: FR-WR

Pouch

Instructions (This manual)

Warranty card

Names of Parts

1Group dial (A/B/C) ........................ P. 19

2Channel dial (1-15) ....................... P. 19

3External ﬂash terminal*

4Latch ............................................. P. 16

5Latch release button ..................... P. 16

6Hot shoe ....................................... P. 17

7X-RCV lamp/button....................... P. 19

8BEEP lamp/button......................... P. 20

9Battery compartment cover........... P. 15

0ON/OFF lamp/button .................... P. 17

aTripod socket

* Use the external ﬂash terminal when you connect a commercial ﬂash via a sync cord. Always

attach the cap when you are not using the external ﬂash terminal.

xIf you connect an older type of commercial ﬂash with a voltage of approx. 350 V or

higher, the wireless receiver will malfunction.

xIf you connect a ﬂash with a communication terminal that does not meet the

Olympus standard, the wireless receiver may malfunction.

Preparing the Receiver

Inserting the batteries (sold separately)Inserting the batteries (sold separately)

Batteries to use

Choose from the following batteries.

• AAA NiMH batteries (x 2)

• AAA alkaline dry-cell batteries (x 2)

xAAA manganese batteries are not usable.

Inserting the batteries

1Open the battery compartment cover.

2Insert the batteries.

• Make sure that the polarity (+/-) is

correct.

3Close the battery compartment cover.

Attaching the wireless receiverAttaching the wireless receiver

This procedure describes how to attach the wireless receiver to a separate ﬂash

stand (FLST-1).

If you are attaching the wireless receiver to a commercial shoe adapter, refer to

the instruction manual for the shoe adapter.

1Hold down the latch release button (1), and

slide the latch in the direction of the arrow (2).

Latch release button

Latch

2Insert the receiver all the way into the ﬂash

stand.

Flash stand

3Slide the latch in the direction of the arrow.

Removing the receiver

Perform Step 1 of the above procedure and remove the receiver from the ﬂash

stand.

Attaching the ﬂash to the wireless receiverAttaching the ﬂash to the wireless receiver

If you are attaching a commercial ﬂash to the wireless receiver, refer to the

instruction manual for the ﬂash.

xMake sure that both the receiver and the ﬂash are turned off.

xDirt or moisture on the electrical contacts may cause a malfunction. Wipe off any

dirt or moisture before you attach the ﬂash to the receiver.

1Insert the ﬂash all the way into the hot shoe of

the receiver.

Hot shoe

Electrical contacts

Turning on the Power

ON/OFF lamp/

button

1Press the ON/OFF button.

xIf the ON/OFF lamp ﬂashes, the batteries are running very low. Replace the

batteries as soon as possible.

Turning off the powerTurning off the power

Press the ON/OFF button.

Automatic power offAutomatic power off

If approximately 60 minutes elapse with no operations, the power will turn off

automatically. Press the ON/OFF button when you want to use the receiver

again.

Radio Wireless Shooting

You can attach a commander to the camera and use the commander as well as

a ﬂash that supports the radio wireless function to control this wireless receiver

through radio communications. This function only works with Olympus products

that support the radio wireless function.

Refer to the Olympus website for information on products that support the radio

wireless function.

Group controlGroup control

You can control up to three groups of receivers. Within each group, the ﬂashes

will ﬁre with the same settings. This function allows you to use an Olympus ﬂash

that does not support radio communications as part of a radio communication

system.

Flash with radio wireless function (sold separately) /

Wireless commander (sold separately)

Group B

Group A

Group C

Flash (sold separately)

Wireless receiver

Flash with

radio wireless

function

(sold separately)

Flash with radio

wireless function

(sold separately)

Communication distanceCommunication distance

The maximum distance for radio wireless communications with this wireless

receiver is approx. 30 meters (98.4 ft.) (under Olympus measurement conditions).

• This distance assumes that there are no obstacles, shielding materials, or

radio interference from other devices.

• The communication distance may be shorter depending on the positions of the

devices, the surrounding environment, weather conditions, and other factors.

FrequencyFrequency

This product uses the 2.4 GHz band for wireless communications. However,

other wireless devices may use the same frequency.

Setup

ON/OFF lamp/button

BEEP lamp/button

X-RCV lamp/button

Channel dial

Group dial

1Turn on the ﬂash.

• Refer to the ﬂash manual for details.

2Press the ON/OFF button to turn on the wireless receiver.

• The ON/OFF lamp will light up.

3Hold down the X-RCV button to select an operating mode.

• The X-RCV lamp is off: RCV mode (You set the ﬂash control mode and

ﬂash intensity on the wireless commander. This

wireless receiver receives the setting information

and ﬁring signal from the wireless commander.

Then, the ﬂash that is connected to this wireless

receiver ﬁres a ﬂash.)

• The X-RCV lamp is on: X-RCV mode (You set the ﬂash control mode and

ﬂash intensity on the ﬂash that is connected to this

wireless receiver. This wireless receiver receives a

ﬁring signal from the wireless commander. Then, the

ﬂash that is connected to this wireless receiver ﬁres

a ﬂash with this wireless receiver’s settings.)

4Turn the group dial to select a communication group.

5Set the ﬂash control mode and ﬂash intensity.

• RCV mode: Set the ﬂash control mode and ﬂash intensity on the

wireless commander.

• X-RCV mode: Set the ﬂash control mode and ﬂash intensity on the

ﬂash that is connected to this wireless receiver.

6Turn the channel dial to select a communication channel.

• Select the same channel that you set on the wireless commander.

Other settingOther setting

Setting a beeping sound to indicate that the ﬂash is ready to ﬁre

1Hold down the BEEP button until the BEEP lamp lights up.

• To disable the beeping sound, hold down the BEEP button until the BEEP

lamp turns off.

Safety Precautions

Read WARNINGS and CAUTIONS thoroughly to ensure safe usage. These

safety precautions protect the users and others and prevent property damage.

WARNING Failure to observe the precautions indicated by this symbol

may result in injury or death.

• Do not use ﬂash in places where it may be exposed to ﬂammable or explosive

gas. Otherwise, ﬁre ignition or explosion may result.

• Do not directly solder the product or modify, remodel, or disassemble.

• Do not cover the light emitting area of the ﬂash with your hand, and do not

touch the light emitting area after continuous ﬁring. It may burn your skin.

• Water and foreign matter inside of the device may cause ﬁre or electric shock.

If the device is immersed in or exposed to water or foreign matter is found

inside of the device, turn off the power immediately and remove batteries with

care. Contact your dealer or consult an Olympus Authorized Service Station.

• To prevent a trafﬁc accident, do not direct the ﬂash at a person operating a

motor vehicle.

• Do not use the ﬂash or AF illuminator in close proximity to others (especially

infants). Keep the ﬂash out of reach of children. Light from the ﬂash can cause

visual impairment.

• To prevent a short circuit, do not use batteries with a damaged external seal

(insulation coating).

• Do not mix old and new batteries, or batteries made by different manufacturers.

• Do not connect substances such as metal to the (+) or (–) of batteries.

CAUTION Failure to observe the precautions indicated by this symbol

may result in injury or property damage.

• If you notice any abnormalities such as odor, noise, or smoke, stop using this

device. Otherwise a ﬁre or burn may result. Remove the batteries carefully

to avoid burning yourself, and contact your dealer or consult an Olympus

Authorized Service Station.

• There is a risk of explosion if the battery is replaced with the incorrect battery

type.

• Do not operate with wet hands. This may cause malfunction or electric shock.

• Do not use or store batteries in areas exposed to extremely high temperatures,

such as in direct sunlight, in an enclosed vehicle on a sunny day, or near a

heater.

• Continuous repeated ﬁring could lead to adverse health effects.

• Dirt or moisture on the contacts with the hot shoe may cause a malfunction.

Wipe off any dirt or moisture before you attach the receiver to the ﬂash.

Using the radio wireless function

• When you use the radio wireless communication function, comply with all local

laws and regulations.

• If you use the product outside the region of purchase, you may violate local

regulations for radio waves. Olympus accepts no liability in this case.

• Turn off the product in hospitals and other locations where medical equipment

is present.

The radio waves from the product may adversely affect medical equipment,

causing a malfunction that results in an accident.

• Turn off the product when onboard aircraft.

Using wireless devices onboard may hinder safe operation of the aircraft.

FCC CautionFCC Caution

Changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

FCC NoticeFCC Notice

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Declaration of Conformity

Model Number : IM013

Trade Name : OLYMPUS

Responsible Party :

Address : 3500 Corporate Parkway, P. O. Box 610, Center Valley,

PA 18034-0610, USA

Telephone Number : 484-896-5000

Tested To Comply With FCC Standards

FOR HOME OR OFFICE USE

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Andere Handbücher für FR-WR

Inhaltsverzeichnis

Andere Olympus Kamerazubehör Handbücher

Olympus

Olympus GS-2 Bedienungsanleitung

Olympus

Olympus PT-045 Bedienungsanleitung

Olympus

Olympus BLS-1 Bedienungsanleitung

Olympus

Olympus PT-EP05L Bedienungsanleitung

Olympus

Olympus PT-055 Bedienungsanleitung

Olympus

Olympus PT-058 Bedienungsanleitung

Olympus

Olympus Camedia B-10LPB Bedienungsanleitung

Olympus

Olympus PT-033 Bedienungsanleitung

Olympus

Olympus SP-310/SP350 Bedienungsanleitung

Olympus

Olympus PPZR-EP07 Bedienungsanleitung

Olympus

Olympus PT 021 Bedienungsanleitung

Olympus

Olympus SHV-1 Bedienungsanleitung

Olympus

Olympus PT-059 Bedienungsanleitung

Olympus

Olympus Quick auto 310 Bedienungsanleitung

Olympus

Olympus CWPC-01 Bedienungsanleitung

Olympus

Olympus PT-EP01 Bedienungsanleitung

Olympus

Olympus PT-E01 Bedienungsanleitung

Olympus

Olympus EVOLT E-330 Bedienungsanleitung

Olympus

Olympus PPO-E05 Bedienungsanleitung

Olympus

Olympus GS-2 Bedienungsanleitung

Olympus

Olympus FR-WR Bedienungsanleitung

Olympus

Olympus PT-EP08 Bedienungsanleitung

Olympus

Olympus PPO-E02 Bedienungsanleitung

Olympus

Olympus BLM-1 Bedienungsanleitung

Beliebte Kamerazubehör Handbücher anderer Marken

Viltrox

Viltrox EF-NEX Montageanleitung

Calumet

Calumet 7100 Series CK7114 Bedienungsanleitung

Ropox

Ropox 4Single Series Bedienungsanleitung

Cambo

Cambo Wide DS Digital Series Betriebsanleitung

Samsung

Samsung SHG-120 Bedienungsanleitung

Ryobi

Ryobi BPL-1820 Bedienungsanleitung

Aegis

Aegis ABL-36020P Bedienungsanleitung

Pentax

Pentax Data Back Fc Bedienungsanleitung

Fantasea

Fantasea EyeGrabber F Series Bedienungsanleitung

Honeywell

Honeywell HDZ20HD Bedienungsanleitung

EGO

EGO BA1400T Bedienungsanleitung

Sima

Sima SRW-62 Bedienungsanleitung

Shape

Shape A7SSMKIT Bedienungsanleitung

Slide Kamera

Slide Kamera HST-2 Bedienungsanleitung

Power works

Power works 2902613 Bedienungsanleitung

SES

SES SE-2047-2 Bedienungsanleitung

Starlite

Starlite OctoDome nxt Bedienungsanleitung

Custom Brackets

Custom Brackets Digital PRO-M Bedienungsanleitung