Omega WRS232-USB Bedienungsanleitung
WRS232-USB
Universal Wireless RS232
to USB Transceiver,
WRS232 Wireless Transmitter,
WUSB Wireless Receiver
WUSB WIRELESS RECEIVER
WRS232 WIRELESS TRANSMITTER
For latest product manuals:
www.omegamanual.info
Shop online at
omega.com®
User’s Guide
RoHS 2 Compliant
The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves
the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, human applications.
Servicing North America:
U.S.A.: Omega Engineering, Inc., One Omega Drive, P.O. Box 4047
Stamford, CT 06907-0047 USA
Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660 Fax: (203) 359-7700
e-mail: [email protected]
For Other Locations Visit omega.com/worldwide
omega.com [email protected]
Table of Contents
Section Page
Section 1 Introduction ........................................................................................ 1-1
1.1 Precautions ................................................................................................ 1-1
1.2 Safety Warnings and IEC Symbols ...................................................... 1-1
1.3 Statement on FCC and Marking .................................................... 1-2
1.4 General Description & System Components ..................................... 1-2
Section 2 Setup and Configuration ................................................................ 2-1
2.1 USB Driver Installation ........................................................................... 2-1
2.2 Wireless Transmitter Module ............................................................... 2-3
2.2.1 Mounting Bracket ........................................................................... 2-4
Section 3 Transmitter/Receiver Configuration ............................................ 3-1
3.1 Multiple Transmitters ............................................................................. 3-1
3.2 Environment/Operating Conditions .................................................... 3-2
3.3 Determining and Maximizing Range .................................................. 3-3
3.4 Operating in Buildings ........................................................................... 3-4
3.5 Building Materials ................................................................................... 3-4
3.6 Penetration Angle of Radio Waves through Walls ........................... 3-4
Section 4 Specifications .................................................................................... 4-1
Approvals, Regulatory Compliance & Patent Notice ............................. 4-2
i
WRS232-USB Transmitter/Receiver
WRS232-USB Transmitter/Receiver
List of Figures
Figure Description Page
Section 1 Introduction
Figure
1-1 IEC Symbols ....................................................................................... 1-1
1-2 WRS232 Wireless Transmitter Module ........................................ 1-2
1-3 WUSB Wireless Receiver Module ................................................. 1-3
1-4 FCC Warning Label .......................................................................... 1-3
Section 2 Setup and Configuration
Figure
2-1 USB Cable Connection .................................................................... 2-1
2-2 Welcome To The Found New Hardware Wizard Screen .......... 2-2
2-3 Install Software Automatically Screen .......................................... 2-2
2-4 Completing The Found New Hardware Wizard Screen ........... 2-3
2-5 General Dimensions - Mounting Bracket .................................... 2-4
2-6 Transmitter Mounting Bracket Assembly .................................... 2-5
2-7 Transmitter Bracket With 1/4-20 Mounting Screw
For Tripod Mount ............................................................................. 2-5
2-8 Transmitter Mounting With DIN Rail Mount Assembly .......... 2-5
2-9 Fresnel Zone ....................................................................................... 2-6
Section 3 Transmitter/Receiver Configuration
Figure
3-1 Determining Maximum Range ....................................................... 3-3
3-2 Operation In Buildings .................................................................... 3-4
ii
iii
Package Inspection
Remove the packing list and verify that you have received all your equipment.
Ifyou have any questions about the shipment, please call our Customer
Service Department at 1-800-622-2378 or 203-359-1660. We can also be reached
When you receive the shipment, inspect the container and equipment for any
signs of damage. Note any evidence of rough handling in transit. Immediately
report any damage to the shipping agent.
The carrier will not honor any damage claims unless all shipping
material is saved for inspection. After examining and removing
contents, save packing material and carton in the event reshipment is
necessary.
The following items are supplied with the WRS232-USB product:
• Wireless Transmitter, WRS232
• Wireless Receiver, WUSB
• USB 4P(A) Male to Mini 5P(B) Male cable
• RJ12 to DB9 connector
• Configuration CD
• DB9 Female to Male adaptor
• Instruction Manua
The following items are supplied with the WRS232 product:
• Wireless Transmitter, WRS232
• RJ12 to DB9 connector
• DB9 Female to Male adaptor
• Instruction Manual
The following items are offered as optional accessories:
UNI-ADAP-9V Universal 9 Vdc @ 1.7A adaptor (100-240 Vac input)-
Recommended to power the wireless transmitter
WRS232-MB Mounting Bracket with DIN Rail
NOTE:
Package Inspection
NOTES:
iv
Section 1 - Introduction
Please read this manual completely before installing and operating your
wireless connector/transmitter and receiver system. It’s important to read and
follow all notes, cautions, warnings and safety precautions before operating
this device. “Device” refers to your wireless/transmitter or receiver unit.
1.1 Precautions
• This device is not designed for use in any medical or nuclear applications.
• Do not operate this device in flammable or explosive environments.
• Never operate with a power source other than the one recommended in this
manual.
• This device has been designed for dry, moisture free indoor applications
only.
• Do not operate this device outside of the recommended use outlined in this
manual.
• No co-location with other radio transmitters is allowed. By definition,
co-location is when another radio device or it’s antenna is located within
20 cm of your device and can transmit simultaneously with your unit.
• Never install the wireless transmitters/receiver within 20 cm or less from
each other.
• Never install and/or operate your wireless RS232 transmitter closer than 20
cm to nearby persons.
There are no user serviceable parts inside your device. Attempting to
repair or service your unit may void your warranty:
1.2 Safety Warnings and IEC Symbols
This device is marked with international safety and hazard symbols
in accordance with IEC standards. It is important to read and follow
all precautions and instructions in this manual before operating or
commissioning this device as it contains important information relating to
safety and EMC. Failure to follow all safety precautions may result in injury
and or damage to your device. Use of this device in a manner not specified will
void your warranty
IEC symbols Description
Caution, refer to accompanying documentation
EU’s Waste Electrical and Electronic Equipment
Compliance
Figure 1-1. IEC Symbols
1-1
Introduction 1
NOTE:
1.3 Statement on FCC Marking
FCC Marking
FCC ID: OUR-XBEEPRO IC #4214A-EXBEEPRO
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: 1.) This device may not cause harmful interference.
2.) This device must accept any interference received, including interference
that may cause undesired operation.
Marking
It is the policy of OMEGA to comply with all worldwide safety and EMI/
EMC regulations that apply. OMEGA is constantly pursuing certification of
its products to the European New Approach Directives. OMEGA will add the
mark to every appropriate device upon certification. For additional
information see Section 10 - Approvals & Regulatory Compliance.
1.4 General Description
OMEGA’s new universal wireless RS232 to USB transceiver interfaces to any
RS232 device, and makes it wireless. The wireless transmitter module connects
to an RS232 device. The wireless receiver module connects to the PC via USB
interface. The PC communicates with the RS232 device through the wireless
receiver module. The wireless transmitter/receiver modules are transparent to
the PC as if it is directly connected to the RS232 device.
Fig. 1-2 shows the wireless transmitter module & general dimensions. Fig.
1-3 shows the wireless receiver module & general dimensions. Fig. 1-4 shows
the FCC Warning label that is affixed to the wireless transmitter/receiver
modules. The transmitter/receiver module comes with two LED indicators.
The green LED indicates wireless data transmission (TX). The red LED
indicates wireless data reception (RX).
Figure 1-2 WRS232 Wireless Transmitter Module
Introduction
1
1-2
– +
DC POWER
INPUT
9V
100 MA WRS232
UNIVERSAL
WIRELESS
RS232
TRANSMITTER
RS232
PORT
SAVE
POWER
SAVE
POWER
20.3
(0.80) 69.9
(2.75)
50.8
(2.00)
SLIDE SWITCH
STANDARD
POWER
STANDARD
POWER
CONFIG
NORMAL
RX
TX
DC
ADAPTOR
INPUT
DIIMENSIONS: mm (in)
RS232
PORT
CONFIG
SLIDE
SWITCH
NORMAL SW2
SW1
Figure 1-3 WUSB Wireless Receiver Module
Figure 1-4 FCC Warning Label
1-3
20.3
(0.80)
69.9
(2.75)
50.8
(2.00)
USB
PORT RX
TX
WUSB
UNIVERSAL
WIRELESS
USB
RECEIVER
USB
PORT
DIIMENSIONS: mm (in)
!
F
FCC ID: OUR-XBEEPRO
IC #4214A-XBEEPRO
Made in U.S.A.
This device complies with Part 15 of
the FCC rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful
interference.
2. This device must accept any
interference received, including
interference that may cause
undesired operation.
Introduction 1
2-1
Setup and Configuration
2
2 Setup and Configuration
Connect the wireless receiver module to the PC with USB cable provided. Fig.
2-1 shows the cable connection.
Figure 2-1 USB Cable Connections
2.1 USB Driver Installation
To install the USB software drivers that are required for your wireless receiver
to operate correctly follow these procedures.
You need to have the Software CD that was supplied with your device
loaded into the CD drive on your PC.
1. Connect the wireless receiver to your computer with the USB cable
provided in the box with your device. You should get a notice box that
indicates that your computer “Has Found New Hardware”
2. Your computer will then launch the Found New Hardware Wizard.
Follow the instructions indicated on the Wizard boxes and the additional
instructions noted in this manual.
After completing the Found New Hardware Wizard your system will
ask that you repeat this process. This is normal. You should repeat
the steps outlined here twice. After the second driver is installed you
should then get the “New Hardware Ready For Use” notice.
NOTE:
NOTE:
Connect to PC
Connect to Wireless
Receiver Module
Andere Handbücher für WRS232-USB
1
Inhaltsverzeichnis
Andere Omega Transceiver Handbücher
