Omega TX92A Bedienungsanleitung

e-mail: [email protected]

For latest product manuals:

www.omegamanual.info

TX92A

Miniature Temperature Transmitters

Shop online at

omega.com

User’s Guide

The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves

the right to alter specifications without notice.

omega.com [email protected]

Servicing North America:

U.S.A. Omega Engineering, Inc.

Headquarters: Toll-Free: 1-800-826-6342 (USA & Canada only)

Customer Service: 1-800-622-2378 (USA & Canada only)

Engineering Service: 1-800-872-9436 (USA & Canada only)

Tel: (203) 359-1660 Fax: (203) 359-7700

e-mail: [email protected]

For Other Locations Visit omega.com/worldwide

TTAABBLLEEOOFFCCOONNTTEENNTTSSPPAAGGEE

1.0 GETTING STARTED

1.1 Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.2 Safety and EMC Considerations . . . . . . . . . . . . . . . . . . . . 1

1.3 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.4 Available Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.5 Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.6 Shock Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.0 CONNECTING POWER AND SIGNAL INPUTS. . . . . . . . . 4

3.0 CALIBRATING THE TRANSMITTER. . . . . . . . . . . . . . . . . 5

4.0 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

LIST OF FIGURES AND TABLES

Figure 2-1 Power Input Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Figure 2-2 Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Figure 3-1 Calibration Setup (Resistance Source). . . . . . . . . . . . . . . . 5

Figure 3-2 Calibration Setup (RTD Simulator). . . . . . . . . . . . . . . . . . . 6

Figure 4-1 Case Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Figure 4-2 Transmitter Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . 8

Table 1-1 Range/Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Table 2-1 Screw-Terminal Pin Assignment . . . . . . . . . . . . . . . . . . . . 4

Table 3-1 Fahrenheit Temperature to OHMs Conversion Chart . . . . . 6

Table 3-2 Celsius Temperature to OHMs Conversion Chart. . . . . . . . 6

SECTION 1 GETTING STARTED

1.1 Unpacking

Remove the packing list and verify that you have received all equipment.

If you have any questions, contact the nearest Customer Service Department, as

listed on the cover of this manual.

Upon receipt of shipment, inspect the container and equipment for any signs of

damage. Note any evidence of rough handling in transit. Immediately report any

damage to the shipping agent.

Note: The carrier will not honor any claims unless all shipping material is saved for

their examination. After examining and removing contents, save packing materials

and carton in the event reshipment is necessary.

1.2 Safety and EMC Considerations

This instrument is a Class III device (8 to 50 Vdc).

Always use a power supply, which complies with EN 60950 safety standard.

EMC Considerations

••Whenever EMC is an issue, always use shielded cables.

••Never run signal and power wires in the same conduit.

••Use signal wire connections with twisted-pair cables.

••Install Ferrite Bead(s) on signal wires close to the instrument if EMC problems

persist.

Failure to follow all instructions and warnings may result in injury!

1.3 General Description

The TX92A Series transmitter accepts platinum 100 ohm sensor type RTDs and will

produce a standard 4-20 mA output signal proportional to that produced by its

attached RTD input. The transmitter does NOT provide isolation between its input and

the 4-20 mA output; therefore, an ungrounded RTD is suggested to prevent possible

ground loops.

The transmitter provides amplification, common-mode rejection and controlling the

current draw from an 8-to-50 Vdc source to produce the 4-to-20 mA output signal.

As much as 800 ohms dropping resistance may be used in the power leads of the

TX92A when the unit is energized from a 24 Vdc source because of the small

compliance voltage needed by the unit.

1.4 Available Ranges

As specified in Table 1-1, the transmitter has 10 ranges. Depending upon the range,

the transmitter can measure temperature span as narrow as 180°F or as wide as

1000°F. A multi-turn, top-accessible potentiometer provides fine span tuning. A

second top-accessible, multi-turn potentiometer provides a zero adjustment which

allows placement of the 4-mA output temperature within +/- 25% for Fahrenheit and

+/- 10% for Celsius of nominal span (refer to Section 3.0, Calibrating the Transmitter,

for more details). Models TX92A-*-L are transmitters with the 4-20mA output

linearized to temperature.

Table 1-1. Range/Models

RRaannggeeMMooddeell

-40 to 140°F TX92A-1 TX92A-1-L

0 to 200°F TX92A-2 TX92A-2-L

0 to 300°F TX92A-3 TX92A-3-L

0 to 500°F TX92A-4 TX92A-4-L

0 to 750°F TX92A-5 TX92A-5-L

0 to 1000°F TX92A-6 TX92A-6-L

-0 to 100°C TX92A-7 TX92A-7-L

-0 to 150°C TX92A-8 TX92A-8-L

-0 to 250°C TX92A-9 TX92A-9-L

-0 to 400°C TX92A-10 TX92A-10-L

1.5 Ordering Guide

The model number describes the functionality of the transmitter.

Model Temperature Range

1 -40 to 140°F

2 -0 to 200°F

3 -0 to 300°F

4 -0 to 500°F

5 -0 to 750°F

6 -0 to 1000°F

7 -0 to 100°C

8 -0 to 150°C

9 -0 to 250°C

10 -0 to 400°C

-L 4-20mA output linearized to temperature

FS **Factory Scaling Option:

**Factory Scaling available for additional charge. Consult factory.

To order additional transmitters, specify TX92A followed by the model number. For

example:

TX92A-2 = RTD Transmitter with a temperature range of -0 to 200°F.

TX92A-2-L = RTD Transmitter with the 4-20mA output linearized to temperature and

a temperature range of -0 to 200°F.

1.6 Shock Resistance

Lightweight TX92A transmitter circuit boards are fabricated from rigid, shock resistant

materials with the components soldered to the circuit board.

The TX92A transmitter's small size permits mounting into thermowells or wall mount-

ing in confined areas.

TX92A-

2.0 CONNECTING POWER AND SIGNAL INPUTS

1. Verify that the transmitter is connected for the correct power

voltage rating.

2. Connect the power supply to pin 4 and the resistance load to pin 5.

3. Connect the sensor to pins 1, 2 and 3.

The transmitter has no power on switch, so it will be in operation as soon as

you apply power.

Figure 2-1 Power Input Setup

+PS and -PS screws accept 2mm (13 gauge) or lighter wire. Input range is 8-50 Vdc.

Table 2-1. Screw-Terminal Pin Assignment

Figure 2-2 Pin Assignment

1 RTD

2 RTD

3 M (Sense)

4 +Power/Signal Output

5 -Power/Signal Output

12345

RANGE:

TYPE: JKTEP

2 3 4 5 6 7 8 91011

DC SUPPLY

8-- 50 VDC

4-- 20mA

INT

+PS

R LOAD

RTD

TRANSMITT R

3.0 CALIBRATING THE TRANSMITTER

Calibration Setup:

1. Insert the reference RTD.

2. Connect RTD simulator.

3. Connect DMM monitor and power supply.

Figure 3-1. Calibration Setup (Resistance Source)

To calibrate the transmitter, follow these steps (refer to Figure 3-1):

1. Locate the model number in Table 3-1 or 3-2 and set the resistance source to

the LO-IN value.

2. Adjust the Zero potentiometer until the milliammeter reads 4.00 mA.

3. Set the resistance source to the HI-IN value (in your appropriate table) and read

the output current on the milliammeter.

4. Adjust the Span potentiometer to obtain the 20 mA on the milliammeter.

5. Set the resistance source to LO-IN resistance. If the output current is not 4.00

mA, repeat steps 2 through 7.

6. When calibration is complete, remove the transmitter from the setup.

RESISTANCE

SOURCE

DC SUPPLY

24 VDC

DMM

(4–20 mA)

MONITOR

(–)

(+)

(–)

(+)

COPPER

WIRE

250 Ohms

INPUT

RTD

WIRE

SPAN

ZERO

3.0 CALIBRATING THE TRANSMITTER (Continued)

An RTD calibrator may be used in place of the resistance source - refer to Figure 3-2.

Figure 3-2. Calibration Setup (RTD Simulator)

Table 3-1. Fahrenheit Temperature to OHMS Conversion Chart

Table 3-2. Celsius Temperature to OHMS Conversion Chart

DMM

(4–20 mA)

MONITOR

(–)

(+)

(–)

(+)

250 Ohms

INPUT

WIRE

SPAN

ZERO

RTD

CALIBRATOR

DC SUPPLY

24 VDC

VVaalluueeMMooddeellNNuummbbeerr//RRaannggee

TTXX9922AA--7788991100

(0 to 100°C) (0 to 150°C) (0 to 250°C) (0 to 400°C)

LO IN 100 Ω 100 Ω 100 Ω 100 Ω

HI IN 138.51 Ω 157.33 Ω 194.10 Ω 247.09 Ω

VVaalluueeMMooddeellNNuummbbeerr//RRaannggee

TTXX9922AA--112233445566

(-40 to 140°F) (0 to 200°F) (0 to 300°F) (0 to 500°F) (0 to 750°F) (0 to 1000°F)

LO IN 84.27 Ω 92.95 Ω 92.95 Ω 92.95 Ω 92.95 Ω 92.95 Ω

HI IN123.24 Ω135.85 Ω156.96 Ω197.71 Ω246.74 Ω293.56 Ω

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Omega Sender Handbücher

Omega

Omega W Series Bedienungsanleitung

Omega

Omega OM-CP-RF Series Bedienungsanleitung

Omega

Omega EWS-RH Bedienungsanleitung

Omega

Omega PHTX-11 Bedienungsanleitung

Omega

Omega FP90 Series Bedienungsanleitung

Omega

Omega CDTX-90 Series Bedienungsanleitung

Omega

Omega UWPC-2-NEMA Bedienungsanleitung

Omega

Omega HX93B Series Bedienungsanleitung

Omega

Omega FMA1001A series Bedienungsanleitung

Omega

Omega TX93A Bedienungsanleitung

Omega

Omega LVU800 Series Bedienungsanleitung

Omega

Omega UWTC Series Bedienungsanleitung

Omega

Omega LVU-700 Bedienungsanleitung

Omega

Omega OS137A Series Bedienungsanleitung

Omega

Omega OS101 Bedienungsanleitung

Omega

Omega DRST-UN Bedienungsanleitung

Omega

Omega UWBT Series Bedienungsanleitung

Omega

Omega OS4000 Series Bedienungsanleitung

Omega

Omega DRST-AC Bedienungsanleitung

Omega

Omega DRST-CM Bedienungsanleitung

Omega

Omega DMD4380 Bedienungsanleitung

Omega

Omega LVU500 Series Bedienungsanleitung

Omega

Omega TX31 Bedienungsanleitung

Omega

Omega FP7002 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung

Excalibur

Excalibur SoundMaster FM Transmitter 144 Bedienungsanleitung