Omnimount QM100-T Bedienungsanleitung

Thank you for purchasing an OmniMount product.

Warranty: Limited Lifetime on manufacturing defects and workmanship.

Specifications are subject to change without prior notice.

Every effort has been made to provide accurate and error-free assembly and installation instructions. OmniMount Sys-

tems disclaims liability for any difficulties arising from the interpretation of information contained in these instructions.

If OmniMount products are used for purposes other than their original intent, OmniMount, its distributors and retailers

shall not be held responsible or liable for injuries or property damage, direct, indirect, or consequential, which may arise

from the inability to use this product safely, properly, and in the manner for which it has been designed and manufac-

tured. Warranty does not apply to products which have been lost, damaged by misuse, abuse, or accident.

OmniMount Systems, Inc.

8201 South 48th Street • Phoenix, AZ 85044-5355

1-800-MOUNT-IT • www.omnimount.com

P/N 1001156—Rev. B 7/2004

Step 4

Install the Wall Plate onto the Monitor Plate using

the supplied 1/4”-20 Screws (3) and Nylon Washers

(10).

Carefully hang the monitor by sliding the keyhole

slots on the Wall Plate over the protruding screws, as

indicated by arrows in Fig. 5.

Tighten the screws holding the Wall Plate.

Note: Tilting the monitor away from the wall, im-

proves access to the wall mounting screws.

Fig. 5

Step 5

Adjust tension of the Tilt Screw (Fig. 5) to provide

the desired degree of adjustability or locking of tilt

mechanism.

QM100T:

LCD Tilt Mount

Installation Instructions

IMPORTANT: Consult a qualified installer if you have any questions

regarding the proper installation of this wall mount system.

Questions? 1-800-MOUNT IT

• Universal VESA mount

• Easy to install

• +15º to -5º of tilt

• Can be inverted

• 40 lbs (18.1 Kg) capacity

QM100T

ID Description Qty

1 Monitor Plate 1

2 Wall Plate 1

3 Screw: 1/4”-20 X 1/2” 4

4 Wall Screw: 6mm x 50mm 2

5 Wall Anchor 2

6 Screw: 4mm x 8mm 4

7 Screw: 4mm x 12mm 4

8 Screw: 5mm x 8mm 4

9 Screw: 5mm x 12mm 4

10 Nylon Washer 4

Step 1

Determine the desired location for the monitor.

Important: Make sure there is adequate mounting space available for

the monitor, considering the monitor dimensions.

The QM100T is supplied with the necessary hardware for either

Wooden Stud Mounting or Masonry Mounting. Determine your

mounting type and proceed accordingly. Fig. 1

Wooden Stud Mounting: Using an electronic stud

finder, locate the center of the wooden stud.

Position the Wall Plate (2) in desired mounting

location over stud.

Level the Wall Plate with a bubble level, and then

using the wall bracket as a template, mark mounting

hole locations over the center of the stud.

Drill 2 mounting holes into the stud using a 5/32” drill

bit.

Masonry Mounting: Position the Wall Plate (2) in desired

mounting location on wall.

Level the Wall Plate with a bubble level, and then using the

wall bracket as a template, mark mounting hole locations on

wall.

Drill 2 mounting holes using a 5/16” masonry bit. Insert

Wall Anchors (5) into the mounting holes, and lightly tap

them flush to the wall with a hammer.

Caution: Wall Anchors should only be used for masonry

mounting. NEVER use wall anchors to mount the QM100T

to drywall.

Step 2

Mount Wall Plate with supplied Wall Screws (4) , and check fit. (Fig. 1) Leave Wall Screwsprotruding slightly so that

Wall Plate can slide over screw heads for installation/removal of monitor.

Remove Wall Plate from wall, and set aside for Step 4.

Attach Monitor Plate to back of the monitor with 4mm or 5mm

supplied hardware. (6-9) (Fig. 4) Check the monitor’s owners man-

ual for correct length screw to use.

Caution: Never force screws into the monitor, as damage may oc-

cur.

Fig. 4

Step 3

The QM100T can be mounted to allow the moni-

tor to Tilt Up or Tilt Down.

To have monitor Tilt Up, the Monitor Plate

should be attached to the monitor with the Pivot

Screw at the top, as shown in Fig. 2.

To have monitor Tilt Down, the Monitor Plate

should be attached to the monitor with the Pivot

Screw at the bottom, as shown in Fig. 3.

Fig. 2 Fig. 3

Andere Omnimount Rack & Stand Handbücher

Omnimount

Omnimount FP-CL Bedienungsanleitung

Omnimount

Omnimount 3N1-S Bedienungsanleitung

Omnimount

Omnimount 30.0 WA Bedienungsanleitung

Omnimount

Omnimount NC200-T Bedienungsanleitung

Omnimount

Omnimount OM10047 Bedienungsanleitung

Omnimount

Omnimount OM1004283 Bedienungsanleitung

Omnimount

Omnimount OM10351 Bedienungsanleitung

Omnimount

Omnimount CP-4 Bedienungsanleitung

Omnimount

Omnimount CI175T Bedienungsanleitung

Omnimount

Omnimount OM10046 Bedienungsanleitung

Omnimount

Omnimount OM10245 Bedienungsanleitung

Omnimount

Omnimount VB60C Bedienungsanleitung

Omnimount

Omnimount 4N1-M Bedienungsanleitung

Omnimount

Omnimount 10135 Bedienungsanleitung

Omnimount

Omnimount UN-A-B Bedienungsanleitung

Omnimount

Omnimount OS80T Bedienungsanleitung

Omnimount

Omnimount POWER 55 Bedienungsanleitung

Omnimount

Omnimount OM10051 Bedienungsanleitung

Omnimount

Omnimount 4N1-S Bedienungsanleitung

Omnimount

Omnimount G3FP Bedienungsanleitung

Omnimount

Omnimount 10041 Bedienungsanleitung

Omnimount

Omnimount SCM50 Bedienungsanleitung

Omnimount

Omnimount RE12W Bedienungsanleitung

Omnimount

Omnimount OS40TP Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung