Omnitron Systems Technology IConverter 2FXM2 Bedienungsanleitung

iConverter 2FXM2 Standalone Module QUICK START GUIDE

The Omnitron iConverter®2FXM2 media

converter and Network Interface Device (NID)

provides Fast Ethernet (100BASE-FX) fiber-to-

fiber media conversion.

The2FXM2conformstoEthernetintheFirstMile

(EFM) fiber standards to support Fiber-to-the-X

(FTTX) Metropolitan and Enterprise LAN

networks. Built-in Operation,Administration and

Maintenance (OAM) functionality enables the

2FXM2 to operate as a managed demarcation

point at the customer premises and network

edge,offeringserviceprovisioningfunctions,such as Quality of Service and Bandwidth

Control (rate-limiting) capabilities.

The 2FXM2 can be managed using Omnitron’s NetOutlookTM SNMP Management

Software, 3rd Party SNMP-Client, Telnet or the Command Line Interface (CLI).

For more information, including the complete User Manual on the 2FXM2 module,

access Omnitron’s documentation download web page to view all relevant documents:

http://www.omnitron-systems.com/downloads.php

INSTALLATION PROCEDURE

1) Configure DIP-Switches

2) Install Standalone Module and Connect Cables

3) Configure Module via Command Line Interface

4) Verify Operation

1) CONFIGURE DIP-SWITCHES

DIP-SWITCH BANK 1

SW1 - PAUSE ENABLE

When the Pause Enable

DIP-switchis in theDOWN

“Off” position (factory

default), the 2FXM2

disables the fiber ports’

ability to send and receive

Pause frames during

network congestion.

Setting this DIP-switch to the UP “On” position, enables the 2FXM2 to receive Pause

frames from its link partner. This enables the 2FXM2 to stop transmitting traffic to its

link partner and store incoming frames from the other port in the internal buffer until the

congestionclears. If the internalbufferof the 2FXM2becomescongested, it willtransmit

a Pause frame to its link partner.

SW2 - FIBER PORT 1 FULL/HALF DUPLEX

Setting this DIP-switch to Half-Duplex “HDX” facilitates a connection that supports

Management Options iConverter, Serial Agent

Network Management

1: Chassis and Module Management

2: Set Module Name Preferences

Management Module Preferences

3: IP and Control Preferences

4: SNMP Preferences

5: Abandon Preference Changes

6: Save Preference Changes

7: Restore Factory Defaults

8: Restart Management Module

9: Other Networking Features

Management Module Maintenance

10: Firmware Update

11: Set Date/Time

IP Address = 192.168.1.220

Chassis Number = 1

Enter Choice, <H>elp, E<x>it >

Figure C: Command Line Interface Menu Options

TheCLI interface allowsforthe detailedconfiguration ofthemodule. It is recommended

to configure the module with an IP address associated with the attached network.

Also, SNMP traphost address should be configured if the module is managed with an

SNMP-based Management System. See the 2FXM2 User Manual for complete

information.

4) VERIFY OPERATION

Once the module has been

installed and configured per

steps1 -3, verify themodule

isoperational by viewingthe

LED indicators.

The Power LED indicates

the module is receiving

power.

The Fiber Optic link LEDs

indicate the fiber optic

connections have been

established. Verify the Link

Modeselection is set to Link

Segment(LS). Until astable

linkis established, leave the

Link Mode configured for LS. After a Link presence is established, the Link Mode

selection can be modified.

LED Function

"Legend" Color Off State On / Blinking State

Power "Pwr" Green No power On: Module has power

Port 1

Fiber Link Activity

"P1" Green No Fiber Link On: Fiber link is active

Blinking: Fiber Data Activity

Port 1

Half/Full Duplex

"FDX" Green Half-Duplex On: Full-Duplex

Port 2

Fiber Link Activity

"P2" Green No Fiber Link On: Fiber link is active

Blinking: Fiber Data Activity

Port 2

Half/Full Duplex

"FDX" Green Half-Duplex On: Full-Duplex

Figure D: LED Indicators

Form 040-8940N-001 B

Omnitron Systems Technology * 140 Technology Dr. * #500 * Irvine, CA 92618

949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com

SW1 SW8

DOWN

Bank 1

Port 1 Port 2

Figure A: DIP-Switch Location

from the power cable wires. Connect the power cables to the GX/TM standalone

unit by fastening the stripped ends to the DC power connector.

WARNING: Note the wire colors used in making the positive and negative

connections. Use the same color assignment for the connection at the DC

power source.

NOTE: If mounting with a safety ground attachment, use the safety ground

screw at the rear of the unit.

Connect the power wires to the DC power source. The Power LED should indicate

the presence of power.

b. Insert the SFP Fiber transceivers into the Port 1 and Port 2 SFP receptacles on the

2FXM2.

NOTE: The release latch of the SFP Fiber transceiver must be in the closed

position before insertion.

c. Connect an appropriate multimode or single-mode fiber cable to the SFP fiber ports

of the installed module. It is important to ensure that the transmit (TX) is attached to

the receive side of the device at the other end and the receive (RX) is attached to the

transmit side. Single-fiber (SF) media converter models operate in pairs. The TX

wavelength must match the RX wavelength at the other end and the RX wavelength

must match the TX wavelength at the other end.

NOTE: In order to support Remote OAM Management Mode, Port 1 of the

2FXM2 must be connected to the Port 1 on the 2FXM2 or link partner.

3) CONFIGURE MODULE VIA COMMAND LINE INTERFACE

To access the Command Line Interface (CLI), connect the 2FXM2 RS-232 Console

Port to the COM port of a computer equipped with terminal emulation software such

as HyperTerminal. The Console Port (DCE) is a mini DIN-6 female connector which

can be changed to a DB-9 connector with the included adapter. The 2FXM2 Console

Port is a standard asynchronous serial interface.

Start HyperTerminal and select the correct COM Port in the HyperTerminal “Connect

To:” window. Set the serial port to the following:

Bits Per Second 57,600

Stop Bits 1

Data Bits 8

Parity NONE

Hardware Flow Control NONE

Once connected, press <ENTER> to bring up a command line prompt on the attached

PC. A new 2FXM2 module does not have a password, and will skip the Password

Entry screen and go straight to the Management Options screen. If a password has

been set, the Password Entry screen will be displayed. Type the password and press

<ENTER>, the 2FXM2 will respond with the Management Options screen:

Half-Duplex. Setting this DIP-switch to Full-Duplex “FDX” facilitates a connection that

supports Full-Duplex operation.

SW3, SW4 - RESERVED

These DIP-switches are for factory use only and must always remain in the DOWN

(factory default) position.

SW5 - FIBER PORT 2 FULL/HALF DUPLEX

Setting this DIP-switch to Half-Duplex “HDX” facilitates a connection that supports

Half-Duplex. Setting this DIP-switch to Full-Duplex “FDX” facilitates a connection that

supports Full-Duplex operation.

SW6, SW7, SW8 - LINK MODES

Themodule supportsmultiple link modes for faultdetection and isolation. Link Segment

should be used for the initial installation of the module. Once installed and operational,

thelink mode can be changed. For detailedinformationonthe operation of the different

Link Modes, download the application note “iConverter Link Modes” available on

Omnitron’s web page:

http://www.omnitron-systems.com/downloads.php

Switch Down

(Factory Default) Up SW6 SW7 SW8 Link Mode Selection

SW1 Off:

Pause Disable PAUS:

Pause Enable Down Down Down Link Segment (LS)

(Factory Default)

SW2 FDX:

Fiber Port 1Full-Duplex HDX:

Fiber Port 1Half-Duplex Up Down Down Link Propagate (LP)

SW3 Reserved Reserved Down Up Down Remote Fault Detect + Link

Segment (RFD + LS)

SW4 Reserved Reserved Up Up Down Remote Fault Detect + Link

Propagate (RFD + LP)

SW5 FDX:

Fiber Port 2 Full-Duplex HDX:

Fiber Port 2Half-Duplex Down Down Up Symmetrical Fault Detect (SFD)

SW6

See Link Mode Selection

Up Down Up Asymmetrical Link Propagate

P1 to P2 (ALP P1-P2)

SW7 Down Up Up Asymmetrical Link Propagate

P2 to P1 (ALP P2-P1)

SW8 Up Up Up Asymmetrical RFD+ LP

P1 to P2

Figure B: DIP-Switches

2) INSTALL STANDALONE MODULE AND CONNECT CABLES

a.The 2FXM2NetworkInterface Device (NID) isavailablein tabletopand wall-mounting

models. Forwall-mounting, attach the NIDtoa wall, backboard or otherflatsurfaces.

For tabletop installations, place the unit on a flat level surface. Attach the rubber feet

to the bottom of the NID to prevent the unit from sliding. Make sure the unit is placed

in a safe, dry and secure location.

To power the unit using the AC/DC adapter, connect the AC/DC adapter to the AC

outlet. Then connect the barrel plug at the end of the wire on the AC/DC adapter to

the 2.5mm DC barrel connector (center-positive) on the chassis. Confirm that the

unit has powered up properly by checking the power status LED located on the front

of the unit.

To power the unit using a DC power source, prepare a power cable using a two-

conductor insulated wire (not supplied) with a 14 AWG gauge minimum. Cut the

power cable to the length required. Strip approximately 3/8 of an inch of insulation

Andere Handbücher für iConverter 2FXM2

Andere Omnitron Systems Technology Medienkonverter Handbücher

Omnitron Systems Technology

Omnitron Systems Technology E1 Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology Omnitron iConverter 10/100M Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology miConverter 10/100 Plus Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology Omnitron 8000-0 Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology FlexPointTM OC12FF Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology OmniConverter GHPoE/S Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology Omnitron iConverter GX/TM2 Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology miConverter 10/100 Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology Omnitron iConverter GX/TM2 Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology iConverter 2FXM2 Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology OmniConverter GPoE+/SX Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology OmniRepeater AS400/3X Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology OmniConverter FPoE/SL Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology miConverter GX/T Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology FlexPoint TR Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology iConverter Gx AN Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology iConverter 2GXM Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology Serial RS-422 and RS-485 to Fiber Media Converter... Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology FlexPoint 100Fx/Tx Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology 10/100 Media Converter miConverter Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology XM5-1G Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology FlexPoint 10FL/2 Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology Fiber-to-Fiber Converter 1000FF Bedienungsanleitung

Omnitron Systems Technology

Omnitron Systems Technology iConverter X21 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung