Omron AUTOMATIC DIGITAL BLOOD PRESSURE MONITOR... Bedienungsanleitung

Instruction Manual

Automatic Digital

Blood Pressure Monitor

Model HEM-703CP

HEM-703CP-xxxx 0692581-7 A

Important

CONTENTS

Important  1

Name and Function of Each Part         2

Preparations for Use                  3

Instructions for Use                   8

When Error Indication Symbols Appear   10

Specications  11

Thank you for purchasing our Digital Blood

Pressure & Pulse Monitoring Kit Please care-

fully read this instruction manual before use

and keep it with your portion of the enclosed

warranty card

PLEASE NOTE:

1 Allow 3 to 5 minutes between blood pres-

sure readings on same arm Repeated

mea-surement results in inaccurate

readings

2 Keep in mind only a physician can ac-

curately determine safe or unsafe limits

of blood pressure This instrument should

be used by non-professional persons only

to determine measurement of blood pres-

sure, not to make any medical judgement

Remember, blood pressure varies during

the day

3 This unit is a precision instrument − avoid

rough handling, direct sunlight, high tem-

perature/humidity and magnetic eld

Fold-ing or bending cuff may result in

damage to cuff

4 Do not inate cuff above 280 mmHg

5 Do not take unit apart You cannot

calibrate unit If you have any difculties

or problems with unit, contact our Service

Center 1-800-634-4350

Name and Function of Each Part

Air Jack

Systolic Bood Pressure Display

Diastolic Blood Pressure and Pulse Display

Printing Paper

Paper Cutter

SPHYG/CLOCK Button

START Button

PRINT / PAPER FEED Button

SET Button

Tab

Air Plug

Air Tube

MODE Selector Button

Main Unit

Cuff

Preparations for Use

1 How to insert the batteries

Battery Cover

1 Take off the battery cover at the back of

the main unit by sliding it in the direction

indicated by the arrow symbol

Replacement

• When the “Replace Batteries” symbol

( ) ashes during measurement,

please replace the batteries with the

new ones

• When the batteries have run down,

random numbers may be displayed

Points to be careful about whan using

the batteries

• When replacing the batteries please

replace all four batteries at once

• Use the same kind of batteries

• Take out weak batteries quickly so as to

avoid causing damage to the machine

• Remove the batteries when the unit is

not used for extended periods

2 Install 4 “AA” size batteries attached so

that the + and - polarities on the

batteries correctly match the polarities in

the battery compartment

3 Replace the cover

Preparations for Use

2 How to Set Time and Date 3 Plug in and Turn on

1 When batteries are installed, the display

shows PM 12:00

1 Insert the air plug into the air jack on the

left side of the main unit correctly

2 When the SPHYG/CLOCK button is

changed to the sphygmomanometer mode,

all the LCD symbols are momentarily

displayed This happens because the unit

is running a check on the display and this

state lasts for approximately one second

3 Once the LCD symbols vanish, the air

release indication symbol (  ) starts

ashing Please wait until the (  ) symbol

goes out

4 When the preparations necessary before

measurement have been completed, the

unit emits a series of beeps and nally the

“Ready to Measure” symbol ( ♥ ) will be

displayed

2 When the MODE button is pressed

down, the “month” sign is displayed

When the SET button is pressed down,

the gure for the month increases Adjust

the “month”

3 When the MODE button is pressed

down after the “month” has been adjusted,

the “day” sign is displayed Adjust the

“day” in the same way as the “month”

4 In the same manner select the “hour” and

“min” with the MODE button and set

each value with the SET button  AM and

PM signs are switched in accordance with

the “hour” adjsutment

5 Press the MODE button for the last time

and return the screen to normal time (hour,

min) display

Initial Display

“Ready to Measure”

Display

Air release

indication symbol

Preparations for Use

4 How to Set the Printing Paper

Please be sure not to print without inserting

printing paper as it will shorten the life span

of the printer head

1 Slide the plastic printer cover in the

direction indicated by the arrow symbol

and remove it from the main unit

4 Insert the printing paper in the installation

section, and then attach the cover back to

the main unit in such a way that the edge

of the paper protrudes from the cover

5 When the PRINT/PAPER FEED button

is pressed while the results of the

measurement are shown on the digital

display, these results, together with the

date and time of measurement are printed

out

6 When purchasing printing paper, ask at the

shop where you purchased the main unit

for further supply Other brands of paper

may be used providing the dimensions are

smaller than 38mm wide and 20mm in di-

ameter However the printing quality may

differ a little

2 Peel off the glued edge of the prontlng

paper included with the unit, and cut it off

to about 2 inches with a pair of scissors,

and then shape and cut the edge for easy

insertion to the printer as shown in the

gure

3 Press the PRINT/PAPER FEED button

while inserting the edge of the printing

paper to the paper feeding slit When the

edge of the paper protrudes sufciently,

release the button and stop feeding

Inserting Direction

Reverse

Front

Preparations for Use

5 Changing the Printer Ink

Though not originally equipped with an ink

roller, the HEM-703CP digital blood pressure

monitor contains enough printer ink to last

about two years when used once a day at

normal room temperature

When the ink on the print out becomes light

and hard to read, purchase a replacement ink

roller from your retailer and install as fol-lows

1 Remove the printer cover

3 Insert the supplement ink roller into the

allotted space next to the printer

4 Replace the printer cover

NOTE: The supplement ink roller should

last about two years, however, if you

need to replace the supplement ink

roller, simply grasp the top of the ink

roller and turn itslightlycounterc1ock-

wise before lifting the roller from the

printer

Supplement ink roller

2 Removethe ink, which came with the

unit when you bought it, from the allotted

space

about 1 inch

Artery

no space

Preparations for Use

6 Attach the Cuff

This cuff has eliminated the need for a

microphone thereby lessening possible

interference from vibrations and noise Fitting

also has been made much easier through the

widening of the artery oscillation detection

area

1 Place the cuff on the left arm so that the air

tube lies across the center of the arm

3 Place your arm on a table or a support with

the palm facing upward so that the cuff is

placed at the same level as the heart

2 Wrap the cuff pulling in a diagonal angle

securely so that the cuff tab is positioned

about one inch above the elbow joint of the

inner your left upper arm (Over the brachi-

al artery)

There should be no space between the

cuff and your arm

NOTE: If you have any difculties wrap-ping

cuff by yourself, we recom-mend that

you ask someone to wrap the cuff for

you

Preparations for Use

7 Apply Pressure to the Cuff

1 When you press the start button, the pump

operates and pressure is applied When

the pressure reaches 170mmHg, the

pump stops automatically

2 When the appropriate pressure has been

reached, the air is automatically released

and the value on the display window

starts to decrease After a while when the

artery oscillations are detected, the ( ♥ )

symbol starts ashing and the unit emits

a beep-ing sound simultaneously The

value shown on the display will continue

to fall

* During measurement, do not shake

the cuff or the air tube

Depress the START

button continuously

untill the cuff is inated

up to the targeted

pressure

After the cuff has

been inated,

release the START

button

Notes:

* If your systolic blood pressure is higher

than 140mmHg, the pump starts again and

the cuff will be inated up to 210mmHg

* If your systolic blood pressure is higher

than 180mmHg, sufcient ination will

not be applied to the cuff by automatic

reination In this case, inate up to

30mmHg higher than your expected

systolic blood pressure by pressing the

start button continuously While press-ing

the start button, the cuff can be in-ated

continuously, and when the start button

is released, the pump stops and the cuff

is no longer inated When the pressure

reaches 300mmHg, the cuff deates

rapidly

* When you want to stop measurememt,

press SPHYG/CLOCK button The pres-

sure will stop and the air is deated rapidly

Pressure being applied

Targetted Blood

Pressure Reached

Indicated Value Drops

Measuring

Measurement

Completed

Alternate Display

Blood Pressure

Reading Display

(for approx 3

seconds)

Pulse Reading

Display

(for approx 15

seconds)

*P: Stands for PULSE

Preparations for Use

8 Blood Pressure and Pulse are displayed

When the deation symbol begins to ash,

the residual pressure in the cuff is then

rapidly released

1 When the unit has continued to deate

to a point when the artery oscillations are

no longer detected, the unit will display

the systolic and diastolic blood pressure

values, along with a long beep, and causes

the deation indication symbol (  ) to start

ashing After this, blood pressure and the

pulse readings are displayed alter-nately

* When you wish to stop measuring during

operation, press the SPHYGICLOCK

button The pump will stop and all the cuff

pressure will be released rapidly

* When the PRINT button is pressed while

the results of the measurement are shown

on the digital display, the results will be

printed

3 Measurement of the blood pressure is

now complete The results will remain

displayed even after the cuff is taken

off If you wish to carry out repeated

measurements, repeat the operation from

Step 6

* The arm gradually becomes congested

when measurements are repeatedly

taken If you wish to take consecutive

measurements, take off the cuff and

wait at least 3 to 5 minutes between

measurements

4 When measurement is completed press

the SPHYG/CLOCK button to return to the

time display If you should forget to press

this button, the display will return to time

display mode automatically after about 5

minutes

2 Upon total cuff deation, a series of

beeps are emitted and the ( ♥ ) symbol is

displayed

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Omron Blutdruckmessgerät Handbücher

Omron

Omron M6 Comfort Bedienungsanleitung

Omron

Omron RX-3 Bedienungsanleitung

Omron

Omron IntelliSense HEM-907 Bedienungsanleitung

Omron

Omron HEM-FL31 Bedienungsanleitung

Omron

Omron INTELLI-SENSE HEM-780 Bedienungsanleitung

Omron

Omron HBP-1300 Bedienungsanleitung

Omron

Omron IntelliSense HEM-790ITCAN Bedienungsanleitung

Omron

Omron Silver BP5250 Bedienungsanleitung

Omron

Omron M2 Compact Bedienungsanleitung

Omron

Omron M7 Intelli IT s AFib Bedienungsanleitung

Omron

Omron 10 Series+ BP791IT Bedienungsanleitung

Omron

Omron BP654 Bedienungsanleitung

Omron

Omron M6 Comfort Bedienungsanleitung

Omron

Omron R6 Bedienungsanleitung

Omron

Omron HEM-7155T-ESL Bedienungsanleitung

Omron

Omron RS8 Bedienungsanleitung

Omron

Omron HEM-6131 Bedienungsanleitung

Omron

Omron HBP-1300 Bedienungsanleitung

Omron

Omron M2 Compact Bedienungsanleitung

Omron

Omron R2 Bedienungsanleitung

Omron

Omron BP710 Bedienungsanleitung

Omron

Omron i-C10 Bedienungsanleitung

Omron

Omron HEM-6121 Bedienungsanleitung

Omron

Omron HEM--670IT Bedienungsanleitung

Beliebte Blutdruckmessgerät Handbücher anderer Marken

Little Doctor

Little Doctor LD7 Bedienungsanleitung

Microlife

Microlife WatchBP Office Targe Bedienungsanleitung

Mx Onda

Mx Onda MX-CP2395 Bedienungsanleitung

Braun

Braun VitalScan 1 Bedienungsanleitung

Little Doctor

Little Doctor LD-91 Bedienungsanleitung

Sanitas

Sanitas SBM 09 Bedienungsanleitung

A&D

A&D LifeSource UB-328 Bedienungsanleitung

König Electronic

König Electronic HC-BLDPRESS200 Bedienerhandbuch

Leicke

Leicke Sharon Bedienungsanleitung

3B SCIENTIFIC

3B SCIENTIFIC U11395 Bedienungsanleitung

Soehnle

Soehnle SYSTO MONITOR 100 Bedienungsanleitung

Nasco Healthcare

Nasco Healthcare Simulaids Life/form LF01095U Referenzhandbuch

Microlife

Microlife WatchBP office Bedienungsanleitung

HoMedics

HoMedics MiBody 360 Bedienungsanleitung

ForaCare

ForaCare FORA P30 Plus Bedienungsanleitung

JOYTECH

JOYTECH DBP-6296B Bedienungsanleitung

visomat

visomat double comfort Bedienungsanleitung

Spacelabs Healthcare

Spacelabs Healthcare 90217A Bedienungsanleitung