Omron E5 N H - Stücklistenhandbuch

ZX-T Series

Cat. No. H08E-EN-01

Digital

Temperature Controllers

Getting Started Manual

Cat. No. H08E-EN-01 Note: Speciﬁcations subject to change without notice.

Authorized Distributor:

Printed in Europe

Cat. No. H08E-EN-01 Digital Temperature Controllers E5CN/E5AN/E5EN/E5GN Getting Started Manual

E5CN

E5AN

E5EN

E5GN

E5CN/E5AN/E5EN/E5GN

Digital Temperature Controllers

Getting Started Manual

Basic Type

Revised August 2010

This manual needs the H04E+E5CN(-U) and H03E+E5EN/AN datasheet for

selection and installation. (This manual is a selection from the full manual H156)

Preface

The E5CN, E5CN-U, E5AN, E5EN, and E5GN are Digital Temperature Controllers. The E5CN and

E5CN-U are both compact temperature controllers, with the E5CN featuring screw terminal connec-

tions, and the E5CN-U featuring socket pin connections. The E5GN can be connected using screw ter-

minals or screwless clamp terminals. The main functions and characteristics of these Digital

Temperature Controllers are as follows:

• Any of the following types of input can be used: thermocouple, platinum

resistance thermometer, infrared sensor, analog voltage, or analog cur-

rent.

• Either standard or heating/cooling control can be performed.

• Both auto-tuning and self-tuning are supported.

• Event inputs can be used to switch set points (multi-SP function), switch

between RUN and STOP status, switch between automatic and manual

operation, start/reset the simple program function, and perform other

operations. (Event inputs are not applicable to the E5CN-U.)

• Heater burnout detection, heater short (HS) alarms, and heater overcur-

rent (OC) functions are supported. (Applicable to E5CN, E5AN, E5EN,

and E5GN models with heater burnout detection function.)

• Communications are supported. (Applicable to E5CN, E5AN, E5EN, and

E5GN models with communications.)

• User calibration of the sensor input is supported.

• The structure is waterproof (IP66). (Not applicable to the E5CN-U.)

• Conforms to UL, CSA, and IEC safety standards and EMC Directive.

• The PV display color can be switched to make process status easy to

understand at a glance.

This manual describes the E5CN, E5CN-U, E5AN, E5EN, and E5GN for basic functions. Read this

manual thoroughly and be sure you understand it before attempting to use the Digital Temperature

Controller and use the Digital Temperature Controller correctly according to the information provided.

Keep this manual in a safe place for easy reference. Refer to the full manual for advanced settings:

E5CN/E5AN/E5EN/E5GN Digital Temperature Controllers User’s Manual (Cat. No. H156).

Refer to the following manual for further information on communications: E5CN/E5AN/E5EN/E5GN

Digital Temperature Controllers Communications Manual Basic Type (Cat. No. H158).

Refer to the following manual for information on the Advanced Type Controllers: E5CN/E5AN/E5EN-H

Digital Temperature Controllers User's Manual Advanced Type (Cat. No. H157).

Visual Aids

The following headings appear in the left column of the manual to help you locate different types of

information.

Note Indicates information of particular interest for efficient and convenient opera-

tion of the product.

1,2,3... 1. Indicates lists of one sort or another, such as procedures, checklists, etc.

©OMRON, 2010

by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of

OMRON.

No patent liability is assumed with respect to the use of the information contained herein. Moreover, because OMRON is con-

stantly striving to improve its high-quality products, the information contained in this manual is subject to change without

notice. Every precaution has been taken in the preparation of this manual. Nevertheless, OMRON assumes no responsibility

for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained in

this publication.

vii

1) It takes approximately two seconds for the outputs to turn ON from after the power supply is turned ON.

Due consideration must be given to this time when incorporating Temperature Controllers into a control

panel or similar device.

2) Make sure that the Temperature Controller has 30 minutes or more to warm up after turning ON the power

before starting actual control operations to ensure the correct temperature display.

3) When executing self-tuning, turn ON power for the load (e.g., heater) at the same time as or before

supplying power to the Temperature Controller. If power is turned ON for the Temperature Controller

before turning ON power for the load, self-tuning will not be performed properly and optimum control will

not be achieved. When starting operation after the Temperature Controller has warmed up, turn OFF the

power and then turn it ON again at the same time as turning ON power for the load. (Instead of turning the

Temperature Controller OFF and ON again, switching from STOP mode to RUN mode can also be used.)

4) Avoid using the Controller in places near a radio, television set, or wireless installing. The Controller may

cause radio disturbance for these devices.

The E5CN, E5CN-H, E5AN, E5AN-H, E5EN, and E5EN-H comply with Lloyd's standards. When applying the

standards, the following installation and wiring requirements must be met in the application.

■Application Conditions

1) Installation Location

The E5CN, E5CN-H, E5AN, E5AN-H, E5EN, and E5EN-H comply with installation category ENV1 and

ENV2 of Lloyd's standards. Therefore, they must be installed in a location equipped with air condition-

ing. They must therefore be installed in a location equipped with air conditioning. They cannot be used

on the bridge or decks, or in a location subject to strong vibration.

2) Wiring Conditions

Install the recommended ferrite core and wrap the line around it three turns for the applicable lines

(e.g., power supply cable line and signal lines) of the models listed in the following table. (See illustra-

tions.) Install the ferrite cores as close to the terminal block of the E5@N as possible. (As a guideline,

the ferrite core should be within 10 cm of the terminal block.)

●Lines Requiring Ferrite Cores

●Recommended Ferrite Core

Note This part is available from Omron stock.

Precautions for Operation

Shipping Standards

Model Signal and power lines provided with ferrite cores

E5CN, E5CN-U, or E5CN-H Input power supply

E5EN, E5AN, E5EN-H, or

E5AN-H

Input power supply and I/O lines (control outputs (1 and 2), communications,

event inputs (1 to 4), transfer output, and external power supply (Advanced

Type models do not have an external power supply.)

Manufacturer Seiwa Electric Mfg. Co., Ltd.

Model E04RA310190100

viii

●Ferrite Core Connection Examples

1. E5CN/E5CN-H

2. E5AN/E5EN/E5AN-H/E5EN-H

−

●B

●

DO NOT

USE

DO NOT

USE

DO NOT

USE

●

Input power

supply

Auxiliary

output 1

Auxiliary output 2

Control output 1

Auxiliary outputs

(relay outputs)

Analog input TC/Pt universal input

Power suppl

AC/DC

3 turns

EV4

EV3

−

DO NOT USE

CT2

CT1

EV1

EV2

CT1/CT2

DO NOT

USE

DO NOT

USE

DO NOT

USE

DO NOT

USE

DO NOT

USE

DO NOT

USE

B (+)

A (−)

DO NOT USE

B (+)

A (−)

RS-485RS-232C

DO NOT USE

Input power

supply

Control output 1

Auxiliary output 3

Auxiliary output 2

Auxiliary output 1

Transfer output 4 to 20 mA DC

(Load: 600 Ωmax.)

Communications

Event Inputs

Control

Output 2

Control

Output 2

External Power

Supply

External power supply

12 VDC, 20 mA

Connected to

communications or

event inputs 1 and 2.

Connected to

control output 2

or external

power supply.

Power

supply

Connected to

control output 1.

Connected to event

inputs 3 and 4.

Connected to

transfer output.

Analog input

TC/Pt universal input

AC/DC

3 turns

Be sure to thoroughly read and understand the manual provided with the product, and check the fol-

lowing points.

Note The tightening torque is 0.5 N·m for the E5CN-U and 0.43 to 0.58 N·m for the

E5GN. The terminal torque is 0.5 to 0.6 N·m for auxiliary output 2 on the

E5GN.

Preparations for Use

Timing Check point Details

Purchasing the prod-

uct

Product appearance After purchase, check that the product and packaging are not dented or

otherwise damaged. Damaged internal parts may prevent optimum

control.

Product model and speci-

fications

Make sure that the purchased product meets the required specifica-

tions.

Setting the Unit Product installation loca-

tion

Provide sufficient space around the product for heat dissipation. Do not

block the vents on the product.

Wiring Terminal wiring Do not subject the terminal screws to excessive stress (force) when

tightening them.

Make sure that there are no loose screws after tightening terminal

screws to the specified torque of 0.74 to 0.90 N·m (see note).

Be sure to confirm the polarity for each terminal before wiring the termi-

nal block and connectors.

Power supply inputs Wire the power supply inputs correctly. Incorrect wiring will result in

damage to the internal circuits.

Operating environ-

ment

Ambient temperature The ambient operating temperature for the product is −10 to 55°C (with

no condensation or icing). To extend the service life of the product,

install it in a location with an ambient temperature as low as possible. In

locations exposed to high temperatures, if necessary, cool the products

using a fan or other cooling method.

Vibration and shock Check whether the standards related to shock and vibration are satis-

fied at the installation environment. (Install the product in locations

where the conductors will not be subject to vibration or shock.)

Foreign particles Install the product in a location that is not subject to liquid or foreign

particles entering the product.

Conventions Used in This Manual

Model Notation

The E5CN-@@@, E5CN-@@@U, E5AN-@@@, E5EN-@@@, and E5GN-@@@ are given as the E5CN,

E5CN-U, E5AN, E5EN, and E5GN when they share functionality.

The following notation is used when specifying differences in functionality.

Note: (1) Excluding the E5GN.

(2) Excluding the E5CN.

(3) The E5AN and E5EN only.

Meanings of Abbreviations

The following abbreviations are used in parameter names, figures and in text explanations. These

abbreviations mean the following:

Note: (1) A heater short indicates that the heater remains ON even when the control output from the Tempera-

ture Controller is OFF because the SSR has failed or for any other reason.

(2) “EU” stands for Engineering Unit. EU is used as the minimum unit for engineering units such as °C,

m, and g. The size of EU varies according to the input type.

For example, when the input temperature setting range is –200 to +1300°C, 1 EU is 1°C, and when

the input temperature setting range is –20.0 to +500.0°C, 1 EU is 0.1°C.

For analog inputs, the size of EU varies according to the decimal point position of the scaling setting,

and 1 EU becomes the minimum scaling unit.

Notation Options

E5@N-@@@B Two event inputs

E5@N-@@@03 RS-485 communications

E5@N-@@H One of HB, HS, and heater overcurrent detection

E5@N-@@HH Two of HB, HS, and heater overcurrent detection (See note 1.)

E5@N-@Q Control output 2 (voltage output) (See note 1.)

E5@N-@@P External power supply to ES1B (See note 1.)

E5@N-@@@01 RS-232C communications (See note 2.)

E5@N-@@F Transfer output (See note 3.)

Symbol Term

PV Process value

SP Set point

SV Set value

AT Au t o - t u n i n g

ST Self-tuning

HB Heater burnout

HS Heater short (See note 1.)

OC Heater overcurrent

LBA Loop burnout alarm

EU Engineering unit (See note 2.)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Omron Temperaturregler Handbücher

Omron

Omron EJ1 EtherCAT Bedienungsanleitung

Omron

Omron E5_N-H Series Bedienungsanleitung

Omron

Omron E5GN Bedienungsanleitung

Omron

Omron E5AZ Bedienungsanleitung

Omron

Omron E5 J Series Bedienungsanleitung

Omron

Omron E5CSZ Bedienungsanleitung

Omron

Omron E5CSV - Bedienungsanleitung

Omron

Omron E5C2 Bedienungsanleitung

Omron

Omron E5GN Bedienungsanleitung

Omron

Omron E5GN Bedienungsanleitung

Omron

Omron E5GN Bedienungsanleitung

Omron

Omron E5AN Bedienungsanleitung

Omron

Omron ES1B Bedienungsanleitung

Omron

Omron E5GN-QTD Bedienungsanleitung

Omron

Omron EJ1G Bedienungsanleitung

Omron

Omron E5AN Bedienungsanleitung

Omron

Omron E5CC Bedienungsanleitung

Omron

Omron E5CS-X - Bedienungsanleitung

Omron

Omron E5CN Bedienungsanleitung

Omron

Omron E5AN-H Bedienungsanleitung

Omron

Omron E5CN Bedienungsanleitung

Omron

Omron EJ1 EtherCAT Bedienungsanleitung

Omron

Omron E5CC-B-800 Bedienungsanleitung

Omron

Omron E5CZ Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema

Opt Lasers

Opt Lasers TEC-8A-24V-PID-HC Bedienungsanleitung

Vaillant

Vaillant VR 92/3 Bedienungsanleitung

Vector

Vector TCY-FT-U Bedienungsanleitung