Omron E5CC Bedienungsanleitung

Page 1of 37

Copying Parameters Between E5CC Temperature Controllers

Quick Start Guide

Version 1.0

September 2015

Page 2of 37

Copying Parameters between E5CC Temperature Controllers

Table of Contents

Purpose ......................................................................................................................................................... 3

Communications Specifications .................................................................................................................... 3

Component to Component ........................................................................................................................... 3

Wiring........................................................................................................................................................ 4

Parameter Setup ....................................................................................................................................... 5

Slave Setup............................................................................................................................................ 5

Master Setup......................................................................................................................................... 6

Component to Component Using CX-Thermo .............................................................................................. 8

Wiring........................................................................................................................................................ 8

E5CC Controller Settings ........................................................................................................................... 9

K3SC DIP Switch Settings.........................................................................................................................10

USB to RS-232C Cable (CS1W-CIF31) Settings ........................................................................................11

Using CX-Thermo ..................................................................................................................................122

Copying Parameters with the Master Device Online........................................................................122

Copying Parameters with the Master and Slave Devices Online......................................................221

Copying Parameters Starting Offline ..................................................................................................31

Page 3of 37

Purpose

Copying parameters between temperature controllers allows quicker change out and setup of multiple controllers. This

can be done with component to component communications or using CX-Thermo in conjunction with other components

such as an interface unit.

This document will show how to copy parameters for the E5CC. This can also be done with other model numbers within

the E5_C family, but some of the information might differ slightly, such as the wiring.

Communications Specifications

Figure 1: Communications Specifications

Component to Component

Both of the units must have communication capabilities, which is the 003 or 004 option selection for E5CC models. Keep

in mind that copy function is only possible between the same model number and the same version of the temperature

controller.

Page 4of 37

Wiring

Wire the controllers as follows for RS-485 communication.

Figure 2: Communications Wiring

Also wire additional inputs and outputs as needed for the application.

Page 5of 37

Parameter Setup

Below is an overview of the communication parameters.

Figure 3: Overview of Communications Programming

Slave Setup

(1) Press the key for at least three seconds to move from the “operation level” to the

“initial setting level.”

(2) Press the key for less than one second to move from the “initial setting level” to

the “communications setting level.”

(3) Scroll through the parameters as shown below by pressing the key. Use the up/down arrow keys to

adjust the value of the parameter.

Page 6of 37

(4) Set to 1.

(5) Press the key for less than one second to move from the “communications setting level” to the

“initial setting level.”

(6) Press the key for at least three seconds to move from the “initial setting level” to the

“operation level.”

Master Setup

Now we will adjust the parameters on the master unit.

(1) Press the key for at least three seconds to move from the "operation level" to the

"initial setting level."

(2) Press the key for less than one second to move from the "initial setting level" to

the "communications setting level."

(3) Select the parameters as shown below by pressing the key. Use the up/down arrow keys to adjust

the parameters.

(4) Only change the following parameters.

a. Set to Fins.

b. Set to 57.6.

c. Set to 0.

d. Set to 1.

e. Set to 2.

Note 1: MAXU should be set to the number of slaves in the system. For one slave, the value would be set to two.

(5) At the copy parameter, press the up arrow key for the unit to copy ALL parameters.

Note: This will copy the parameters to all of the slave units. To copy the parameters only to certain units, select

the number of the slave unit to receive the copied parameters (e.g., 1 for slave unit number 1, 4 for slave unit

number 4).

Page 7of 37

During the copying process below is what appears on the controllers. Once the copy process is started, it is not

possible to stop the copying operation.

After the copy is complete, this is what is shown on both units.

(6) Press the key for less than one second to move from the "communications setting level" to the

"initial setting level."

(7) Press the key for at least three seconds to move from the "initial setting level" to the

"operation level."

Master Unit

Slave Unit

Master Unit

Slave Unit

Page 8of 37

Component to Component Using CX-Thermo

Both of the units must have communication capabilities, which is the 003 or 004 option for E5CC models. Keep in mind

that copy function is only possible between the same model number and the same version of the temperature

controller. Additional products that were used include the following:

•K3SC interface converter,

•CS1W-CIF31 interface unit between USB serial communication and RS-232C,

•D-SUB 9 pin connector (needs a female connection), multi-conductor cable, or K32-23209 pre-made cable,

•CX-Thermo, and

•S8VK-G power supply.

Wiring

Below displays the wiring from the D-SUB 9 pin connector to the K3SC.

Figure 4: K3SC and 9 Pin Connector Connections

Page 9of 37

Shown is the wiring from the K3SC (displayed as Host RS-485) to the E5CC temperature controllers.

Figure 5: E5CC to K3SC Wiring

E5CC Controller Settings

Below are the default settings on the controller.

Figure 6: Default Communications Settings

Each controller needs a unique communications number. Start with unit number 1.

The remaining settings should be default.

Page 10 of 37

K3SC DIP Switch Settings

Set the K3SC DIP switches to match the settings on the E5CC temperature controllers.

Figure 7: K3SC DIP Switch Settings

DIP switches 0-8 should be set to off. If the default baud rate, data length, stop bits, and parity were used, then all of the

DIP switches would be set to off.

Andere Handbücher für E5CC

Inhaltsverzeichnis

Andere Omron Temperaturregler Handbücher

Omron

Omron E5CN-H Bedienungsanleitung

Omron

Omron EJ1 EtherCAT Bedienungsanleitung

Omron

Omron E5EN Bedienungsanleitung

Omron

Omron E5ZN Series Bedienungsanleitung

Omron

Omron E5ZN Series Bedienungsanleitung

Omron

Omron E5CSV - Bedienungsanleitung

Omron

Omron E5CD-B Bedienungsanleitung

Omron

Omron ES1B Bedienungsanleitung

Omron

Omron E5CN Betriebsanleitung

Omron

Omron E5GN-RTC Bedienungsanleitung

Omron

Omron E5AN-H Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

Omron

Omron E5GN Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

Omron

Omron EJ1 EtherCAT Bedienungsanleitung

Omron

Omron CELCIUX Bedienungsanleitung

Omron

Omron E5EC-T Bedienungsanleitung

Omron

Omron E5 J Series Bedienungsanleitung

Omron

Omron E5CN Bedienungsanleitung

Omron

Omron E5GC-6 Series Bedienungsanleitung

Omron

Omron E5AN Bedienungsanleitung

Omron

Omron E5CS-U Bedienungsanleitung

Omron

Omron E5ZN-SCT Bedienungsanleitung

Omron

Omron E5CD-B-800 Series Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema

Opt Lasers

Opt Lasers TEC-8A-24V-PID-HC Bedienungsanleitung

Vaillant

Vaillant VR 92/3 Bedienungsanleitung

Vector

Vector TCY-FT-U Bedienungsanleitung