Omron NS10-TV Series Bedienungsanleitung

Cat. No. V098-E1-05

Programmable Terminals

Host Connection Manual:

Host Link

NS15-TX_, NS12-TS_,

NS10-TV_, NS8-TV_,

NS5-SQ_, NS5-TQ_, NS5-MQ_

OPERATION MANUAL

Introduction

This manual describes the configuration and settings required for communicating with the

host devices used by NS-series Programmable Terminals for Host Link communications.

First familiarize yourself with the contents of the manuals related to NS-series

Programmable Terminals (the NS-series Setup Manual, NS-series Programming Manual,

and the CX-Designer online help), and then use this manual for Host Link communications.

1-1 Overview

This section provides an overview of connecting an NS-V1/V2 PT to an OMRON

Programmable Controller that supports Host Link communications.

The NS-V1/V2 PT is connected 1:1 to the CPU Unit or a Host Link Unit of an OMRON PLC.

Host Link communications are used to read and display or write the words and settings in the

host PLC.

NS-V1/V2 PT serial ports A and B can both be connected to a host by means of the Host

Link protocol.

Reference

When an NS-V1/V2 PT and a PLC are connected by

Host Link, it is not possible to change to RUN Mode.

If the PLC is set for RUN Mode, it is automatically

switched to Monitor Mode. For example, if a

compatible Programming Console is connected to

the PLC and the PLC operating mode is switched to

RUN mode, the password display for the Monitor

Mode will be displayed at the Programming Console.

1-2 Connection Configuration

This section describes the system configuration required for connecting to the host by Host

Link communications.

1-2-1 NS-V1/V2 Configuration Required for Connection

 NS-V1/V2 Models

One of the following NS-V1/V2 PTs is required to connect with the host by Host Link

communications.

Model

NS15-TX01@-V2

NS12-TS0@(B)-V1/-V2

NS10-TV0@(B)-V1/-V2

NS8-TV0@(B)-V1/-V2

NS8-TV1@(B)-V1

NS5-SQ@@ (B)-V1/-V2

NS5-TQ@@ (B)-V2

NS5-MQ@@ (B)-V2

Reference

NS-series PTs without the -V1 or -V2 suffix do not

support Host Link communications. One of the above

NS-V1/V2 models must be used.

 NS-V1/V2 System Program

To connect to the host by means of Host Link communications, system program version 6 or

later must be installed in the NS-V1/V2 PT.

System program

Ver. 6 or later

 Communications Ports

Communications

port

Applicable communications method

Serial port A Host Link

1:1 NT link

1:N NT link

Memory link

(Bar-code reader input)

(Temperature controller connection)

(CX-Designer connection)

Serial port B Host Link

1:1 NT link

1:N NT link

Memory link

(Bar-code reader input)

(Temperature controller connection)

(CX-Designer connection)

The following table shows the communications methods that can be used in combination

when serial ports A and B are used at the same time.

Serial port B

Host Link

1:1 NT Link

1:N NT Link

Memory link

Bar-code

reader

Temperature

controller

CX-Designer

connection

Host Link YES YES YES YES YES YES YES

1:1 NT link YES YES YES YES YES YES YES

1:N NT Link YES YES YES YES YES YES YES

Memory link YES YES YES No YES YES YES

Bar-code reader YES YES YES YES No YES YES

Temperature controller YES YES YES YES YES YES YES

Serial port A

CX-Designer connection YES YES YES YES YES YES No

 Communications Setup

The following table shows the communications settings required at the NS-V1/V2 PT and the

host to connect to the host by means of Host Link communications.

Setup

location

Settings (See note 2.)

NS-V1/V2 PT Baud rate: 9,600 or 19,200 bps (See note 1.)

Host Start bits: 1 bit

Data: 7 bits

Stop bits: 2 bits

Parity: Even

Host Link unit number: 0

Baud rate: 9,600 or 19,200 bps (See note 1.)

Note 1: The baud rate settings must be the same for both the NS-V1/V2 PT and the host.

2: Use the 1:N protocol setting.

1-2-2 Applicable PLCs

The OMRON PLCs listed below can be connected as hosts using Host Link communications.

The connection can be made either directly to the built-in serial port on the CPU Unit or to a

Host Link Unit mounted to the PLC.

C Series

C200HS, C200HX/HG/HE(-Z), CQM1, CQM1H, CPM2A/CPM2C, CPM1/CPM1A, C500,

C1000H, C2000H

CV Series

CV500, CV1000, CV2000, CVM1

CS/CJ Series

CS1G/CS1H, CS1G-H/CS1H-H, CJ1G, CJ1G-H/CJ1H-H, CJ1M, CP1H/CP1L, CJ2H,

CJ2M

Andere Handbücher für NS10-TV Series

Dieses Handbuch passt für folgende Modelle

Andere Omron Touch-Terminal Handbücher

Omron

Omron NT631 Series Bedienungsanleitung

Omron

Omron NT620C Bedienungsanleitung

Omron

Omron NS7 Series Benutzerhandbuch

Omron

Omron NB-series Gebrauchsanweisung

Omron

Omron NT21 Bedienungsanleitung

Omron

Omron NT3S Bedienungsanleitung

Omron

Omron DeviceNet DRT2-ID16S-1 Bedienungsanleitung

Omron

Omron NA-series Gebrauchsanweisung

Omron

Omron NS10-TV Series Betriebsanleitung

Omron

Omron DeviceNet DRT2-AD04 Bedienungsanleitung

Omron

Omron NSH5 Series Bedienungsanleitung

Omron

Omron NT30C-ST141-E Bedienungsanleitung

Omron

Omron NA-series Gebrauchsanweisung

Omron

Omron NS-CXDC1-V1 Bedienungsanleitung

Omron

Omron NT2S-SF123B-E - Gebrauchsanweisung

Omron

Omron NA-series Gebrauchsanweisung

Omron

Omron WT30 Bedienungsanleitung

Omron

Omron NP3 Series Referenzhandbuch

Omron

Omron NS12-TS00 Series Benutzerhandbuch

Omron

Omron Programmable Terminals NT631 Benutzerhandbuch

Omron

Omron NB3Q-TW**B series Installations- und Betriebshandbuch

Omron

Omron NS - Benutzerhandbuch

Omron

Omron NT20S Bedienungsanleitung

Omron

Omron NT620S Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung