Omron NS12 Gebrauchsanweisung

NS Series

Quick Start Manual

OMRON NS Series Quick Start Manual

Page 2

Visual Aids

The following headings appear in the left column of the manual to help you locate different

types of information.

Note Indicates information of particular interest for efficient and convenient operation of

the product.

1, 2, 3… Indicates lists of one sort or another, such as procedures, checklists etc.

Indicates place in the software windows where functions can be found

corresponding the of the list.

or transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording,

or otherwise, without the prior written permission of OMRON.

All copyright and trademarks acknowledged.

No patent liability is assumed with respect to the use of the information contained herein.

Moreover, because OMRON is constantly striving to improve its high-quality products, the

information contained in this manual is subject to change without notice. Every precaution has

been taken in the preparation of this manual. Nevertheless, OMRON assumes no

responsibility for errors or omissions. Neither is any liability assumed for damages resulting

from the use of the information contained in this publication.

OMRON NS Series Quick Start Manual

Page 3

Table of Contents

1How to install the softwares .............................................................................................................4

2How to operate with the PT..............................................................................................................6

2.1 NS12/NS10 Rear Panel............................................................................................................7

2.2 NS8 Rear Panel........................................................................................................................8

2.3 Starting the PT for the First Time .............................................................................................9

2.4 How to use System Menu.......................................................................................................11

2.5 Communication methods........................................................................................................11

3How to create a simple screen.......................................................................................................13

3.1 Creating a New Project...........................................................................................................13

3.2 Project & Screen properties....................................................................................................14

3.3 Explanation of NS Terminal memory......................................................................................17

3.3.1 The Internal Memory ($B, $W) ........................................................................................17

3.3.2 The System Memory ($SB, $SW) ...................................................................................17

3.4 System Settings......................................................................................................................20

3.5 Host Registration ....................................................................................................................25

3.6 Creating a screen ...................................................................................................................26

3.6.1 Screen Object list ............................................................................................................27

3.6.2 Screen example...............................................................................................................30

4How to debug a project..................................................................................................................35

4.1 Transferring Data to/from NS .................................................................................................36

4.1.1 Before Connecting...........................................................................................................36

4.1.2 Starting Data Transfer .....................................................................................................36

4.1.3 After transferring data......................................................................................................39

5Useful Tips .....................................................................................................................................41

Terminology...........................................................................................................................................43

OMRON NS Series Quick Start Manual

Page 4

How to install the softwares

Please read the following remarks before installing any NS software.

• Do not install NS-Designer on a computer in which FinsGateway Ver. 2 and an

SLK, SNT, or SYSMAC Board are installed.

• If NS-Designer Ver. 2.x, Ver.3.x, Ver.4.x , or Ver.5.x is already installed, a dialog

box to confirm deletion of this version will be displayed. Click the OK Button to

start deleting this version. To exit the setup program, click the Cancel Button and

then click the Exit Button. FinsGateway will not be uninstalled by this operation.

• If FinsGateway Ver. 2 is already installed, always uninstall it before installing NS-

Designer. For details on uninstalling FinsGateway Ver. 2, refer to NS Series

Operation Manual (V074-E1-xx), page 2-6, section 2-2-3.

• Before installing NS-Designer in Windows NT, 2000 or XP, log onto the computer

as the administrator to ensure that system DLL files can be overwritten. If

overwriting system DLL files fails, NS-Designer may not operate properly.

Installation Procedure:

1, 2, 3… 1. Start up Windows 95, 98, NT, Me, 2000, or XP.

2. Close all applications before executing installation. Execute the

following files from the NS-Designer CD-ROM according to the

OS being used and then restart the computer.

Windows 95

a) Execute <CDROM>:\Update\401comupd.exe, and then restart

the computer.

b) Execute <CDROM>:\Update\DCOM\English\dcom95.exe, and

then restart the computer.

Windows NT , 2000 , or XP

Execute <CDROM>: \Update\401comupd.exe, and then restart

the computer.

Windows 98, 98SE or Me

No particular operations are required.

3. Place the NS-Designer CD-ROM in the CD-ROM drive. The setup

program is started automatically.

If the setup program does not start automatically, such as after

executing uninstall, locate Setup.exe in the CD-ROM using

Windows Explorer, and then double-click the file to execute the

setup program.

4. The NS-Designer Setup Wizard will be displayed. Install the NS-

Designer by following the instructions in the Setup Wizard.

5. A confirmation message for using FinsGateway Help may be

displayed. Click OK.

6. When installing FinsGateway, the window for registering user

information will be displayed. Enter the user name and

OMRON NS Series Quick Start Manual

Page 5

organization.

After entering the information, click the OK Button.

A dialog box confirming the registered information will be

displayed. Check the information and then click the OK Button.

7. The FinsGateway Units for which installation is possible can be

selected. ETN_UNIT and Serial Unit, which are already selected,

are required for transferring projects to the PT. Controller Link

Unit can be selected only if there is a Controller Link Board

mounted to the computer.

8. The screen for specifying the installation destination will be

displayed.

Specify the directory in which NS-Designer will be installed. The

following directory is displayed as the default installation

destination:

Windows 95, 98, or Me:

C:\Program Files\OMRON\FinsServer95

Windows NT, 2000, or XP:

C:\Program Files\OMRON\FinsServerNT

After specifying the directory, click the Next Button.

(The window will not be displayed if FinsGateway Ver. 3.0 has

been installed.)

9. The window to specify the folder in the Start Menu in which to

folder in the Windows Start Menu folder for creating a shortcut to

FinsGateway. The following folder is displayed as the default

location for creating shortcut keys:

Start Menu\Programs\Omron\FinsGateway

After specifying the folder, click the Next Button.

10. Installation will be executed. During installation, the installation

progress is displayed as a percentage.

11. When installation has been completed, the FinsGateway version

can be upgraded. Click the Yes Button to start the upgrade.

12. When installation has been completed, the Finished Window will

be displayed. Select whether or not to restart the computer

immediately, and click the Exit Button to complete the installation.

13. Always restart the computer after installation before using NS-

Designer!

Note To uninstall the FinsGateway or/and NS-Designer, please refer to

NS-Series Operation Manual (V074-E1-xx).

OMRON NS Series Quick Start Manual

Page 6

How to operate with the PT

The part names and functions of the PT are described below. In general, the PT can

operate via RS232/RS422-, Ethernet- and Controller Link (CLK) communication. The

host of the RS232/RS422 communication can be PLC, PC or Bar Code Reader.

Ethernet and CLK are used for bus communication and the purposes of use are

almost unlimited. In addition there is possibility to attach the video board to the NS12,

the NS10, and the NS8. It can be used for view the live video image from Vision

Systems camera or surveillance camera.

Also e.g. logged data and screen data can be saved in the Compact Flash memory

card.

OMRON NS Series Quick Start Manual

Page 7

2.1 NS12/NS10 Rear Panel

Expansion Interface Connector

Used to mount the Vi deo Input Unit or the

Controller Link Interface Unit.

Reset Switch

Used to ini tial i ze the PT.

The status of screen data, other

reg i stered data, and memory switches,

however, will not change.

Bat t er y C ove r

The battery is installed

underneath the cover.

Ethernet Connector

Used to connect the

Ether net cable. Uses a

10Base/100BASE-T

8-pin RJ45 modular

plug.

DIP Switch

Used to set the settings for

transmi tti ng data using the

MemoryCard.

Memory Card Connector

Used to connect the memory

card for storing and

transmi tti ng screen data, l og

data, and system progr ams.

Serial Port B Connector

Used to connect the host,

NS-Desi g ner, and Bar Code Reader.

Uses an RS-232C 9-pin connector.

USB Slave Connector

This is a USB Type B

connector . (It cannot

be used wi th NS Ver .

5.0 systems.)

USB Host Connector

Used to connect to

printers. It is a USB Type

conn

ctor.

FG Terminal

Used to prevent malfuncti ons

due to noise interference.

Main Circuit DC Input Terminal

Used to connect the power

supply.

Power Input Terminal Block Cover

Cover s the power input terminal block.

Serial Port A Connector

Used to connect the host,

NS-Desi g ner, and Bar Code Reader.

Uses an RS-232C 9-pin connector.

OMRON NS Series Quick Start Manual

Page 8

2.2 NS8 Rear Panel

Expansion Inter face Connector

Used to mount the Video Input Unit or the

Contr oll er Link Interface U nit.

Reset Switch

Used toinitialize the PT.

The status of screen data,

other r eg is ter ed data, and

memory switches, however,

will not chang e.

Battery Cover

The batter y is installed

underneath the cover.

Ethernet Connector

Used to connect the

Ethernet cable. Uses a

10Base/100BASE- T 8-pin

RJ45 modul ar pl ug .

DIP Switch

Used to set the settings for

tr ansmitti ng data using the

MemoryCard.

Memory Car d Connector

U sed to co nn ect t h e m em ory c ar d

for stor ing and tr ansmitti ng

scr een d ata , l og d ata, an d s yst e

pr og rams.

Seri al Port B C onnector

U sed to co nn ect th e h os t, N S- Desi g ner , an d

Bar Code R eader. U ses an RS- 232C 9-pi n

connector.

USB Slave Connector

This is a USB Type B

connector. ( It cannot be

used with NS Ver. 5.0

systems.)

USB Host C onnector

Used to connect to prin ters.

It is a USB Type A

connector.

FG Terminal

Used to pr event malfuncti ons

due to noise interfer ence.

Main Cir cuit DC Input Terminal

Used to connect the power

supply.

Power Input Terminal Block Cover

Covers the power input terminal block.

Serial Port A Connector

U sed to co nn ect t h e h os t, NS- Desi g ner , an d

Bar C ode Reader . U ses an RS- 232C 9-pin

connector.

OMRON NS Series Quick Start Manual

Page 9

2.3 NS5 Rear Panel

Local Bus Interface Connector

Used to connect to an Expansion Interface Unit.

(It cannot be used with NS Ver. 5.0 systems.) Current

Expansion Interface Units cannot be connected.

Reset Switch

Used to initialize the PT. The status

of screen data, other registered data,

and memory switches, however, will

not change.

Serial Port A Connector

Used to connect the host, NS -

Designer,

and Bar Code Reader.

Uses an

232C 9-

pin connector.

Battery Cover

The battery is installed

underneath the cover.

DIP Switch

Used to set the settings for

transmitting data using the

Memory Card.

Memory Card Connector

Used to connect the memory card for

storing and transmitting screen data, log

data, and system programs.

Serial Port B Connector

Used to connect the host, NS -Designer,

and Bar Code Reader. Uses anRS-232C 9-

pin connector.

Power Supply Input Terminals

Used to connect

the power supply.

Ethernet Connector

Used to connect the Ethernet cable.

Uses a 10Base -T/100Base-T 8-pin

odular plug.

USB Slave Connector

This is a USB Type B connector.

(It cannot be used with NS Ver. 5.0

sys

tems.)

FG Terminal

Used to prevent malfunctions

due to noise interference.

2.4 Starting the PT for the First Time

Always perform the following operations when turning ON the PT for the first time

after purchase.

A. Select the operating language.

B. Format the screen data area.

C. Set the date and time.

Operate according to the following conditions.

1. When the power is turned ON to the PT, the error message will be displayed.

Press the OK Button.

2.The System Menu will be displayed. Almost all texts are Japanese. You should see

the language selection box on the lower right (Select Language). Select English

and press the [Write] button. The question window will appear. Press the left

button, which means YES (text is Japanese). The completed message will

appear so press [OK] button. Now all texts should be in English. See the picture

below:

OMRON NS Series Quick Start Manual

Page 10

3. You are already in the [Initialize] tab (the first tab). Press the [Screen Data Area]

button.

4. The warning message will be displayed. Press the Yes Button to format the

screen data. Do not turn OFF the power while formatting is in progress.

The time required for formatting depends on PT model The NS8 finishes

formatting instantly.

5. When formatting has been completed, the message will be displayed. Press the

OK Button.

6. Select the [PT Settings] tab. Set the time and date.

7. Press the date display area under the heading "Calendar Check". A dialog box

will be displayed. Input the date in yyyy/mm/dd format.

Example: Enter January 1st, 2000 as 2000.1.1.

8. Press the time display area under the heading "Calendar Check". A dialog box

will be displayed. Input the time using a 24-hour clock in hours/minutes/seconds

format.

Example: Enter 06:01:01 p.m. as 18.1.1.

9. The red [Write] button is the lower right corner in the [PT Settings] tab. The write

operation is not needed because the time and date settings will be enabled

immediately after they have been input in the dialog box.

Andere Handbücher für NS12

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Omron Touch-Terminal Handbücher

Omron

Omron NT2S-SF122B-E START V1.03 Gebrauchsanweisung

Omron

Omron NA-series Gebrauchsanweisung

Omron

Omron NS10-TV Series Betriebsanleitung

Omron

Omron NT631 Series Bedienungsanleitung

Omron

Omron NP Series Bedienungsanleitung

Omron

Omron NS - Betriebsanleitung

Omron

Omron NT4S Bedienungsanleitung

Omron

Omron NT31 Series Installationshandbuch

Omron

Omron ns series Benutzerhandbuch

Omron

Omron NP3 Series Referenzhandbuch

Omron

Omron PC CONNECTION - 04-1997 Bedienungsanleitung

Omron

Omron NT31 Series Benutzerhandbuch

Omron

Omron WT30 Bedienungsanleitung

Omron

Omron NB-series Bedienungsanleitung

Omron

Omron NS - Gebrauchsanweisung

Omron

Omron NB3Q-TW**B series Installations- und Betriebshandbuch

Omron

Omron Programmable Terminals NT631 Benutzerhandbuch

Omron

Omron NS - REV 04 Bedienungsanleitung

Omron

Omron PRT1-COM Bedienungsanleitung

Omron

Omron NT2S-SF121B-E - Bedienungsanleitung

Omron

Omron NA-series Bedienungsanleitung

Omron

Omron NT30 Bedienungsanleitung

Omron

Omron NV Series Benutzerhandbuch

Omron

Omron NA-series Gebrauchsanweisung

Beliebte Touch-Terminal Handbücher anderer Marken

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

Prestel

Prestel VCS-G2PRO Bedienungsanleitung