Oneida Air Systems AHR000025 Bedienungsanleitung

oneida-air.com1-800-732-4065

Rev: A 20230314LL Doc. #ZBI000054

Hose Reel

#AHR000025

INSTRUCTION SHEET

Once you complete installation of your Hose Reel, please either

scan the QR code or visit oneidaair.wufoo.com/forms/hose-tester

to provide your honest feedback to help us make a great product!

2Oneida Air Systems

System Contents

ID Part number Part description Qty

A* --------------- Body Assembly 1

A1* AAC810025 Core 2

A2* AHM000025 Wall Mount Plate 2

A3* AHS000025 Handle Side Assembly 2

A4* AHS000251 Outlet & Brake Side Assembly 2

B AHH500513 Handle 1

B1 --------------- Screw 1

B2 --------------- Spring 1

CDFH000025 2.5" Outlet Coupler 1

DAFS000011 8-32 x 3/8”Button Head Screw 3

ID Part number Part description Qty

E ACT000238 Brake 1

E1 -------------- 1/4"-20 Hex Nut 2

FAFW000008 2" Nylon Spacer 1

GAFS000010 1/4"-20 X 3" Button Head Screw 1

DAFS000011 8-32 x 3/8" Button Head Screw 4

H ACL000003 3" Loop Clamp 1

IAFS000004 #10 x 1/2'' Self-Drilling Screw 1

JVSHRFB250 2.50" X 25' Hose 1

KACB360000 Turn Key Hose Clamp 1

C D

H I

B2B1

If you cannot find an item on the list examine the packaging materials very

carefully. *Certain components are pre-installed for ease of installation.



Assembly Instructions

3oneida-air.com

You will need the following tools:

WALL MOUNTING BRACKET

Stud Finder Light Adhesive Tape Allen Wrench Clamp

Tack / Center Punch / Nail Tape Measure / Ruler Flathead Screwdriver Power Drill

Wall Mounting Fasteners * Level Tool Pencil / Marker Drill Bit (for your wall fastener)

*You will need to supply your own wall mounting hardware. Use appropriate fasteners for the wall type you are

installing your system onto (e.g. lag bolts, drywall anchors, etc.). Maximum Fastener Diameter: 3/8". Maximum

Washer Outside Diameter: 5/8".

1 read the 1/4"-20 X 3" Screw (G) through the

Spacer (F), Brake (B) and both 1/4"-20 Hex

Nuts (E1) as shown in [FIG. 1].

2 Secure the Brake Assembly (B) to the Outlet

& Brake Side Assembly (A4) using four 8-32 x

3/8" Screw (D) as shown in [FIG. 2a].

Secure the Outlet Coupler (C) to the Outlet &

Brake Side Assembly (A4) using three 8-32 x

3/8" Screws (D) as shown in [FIG. 2c].

read the Screw (B1) through the Spring (B2)

and Handle (B) and secure to the Handle Side

Assembly (A3) [FIG. 2b].

G F

A3 A4

B1 B2 B

FIG. 2a

FIG. 2b

FIG. 1

FIG. 2c

4Oneida Air Systems

Assembly Instructions

THE WALL BRACKET SHOULD BE MOUNTED TO A STURDY, REINFORCED WALL E.G. CONCRETE WALL,

WOODFRAMED WALL, ETC. WALL ANCHORS CAN BE USED IF MOUNTING ON DRYWALL. THE INCLUDED

TEMPLATE INDICATES THE PROPER DRILL HOLES AND THE FULL, ASSEMBLED SIZE OF THE WALL

BRACKET.

Wall

Hose

Reel

3 Identify where you will install the Hose Reel

in your shop and how the hose reel will be

oriented [FIG. 3a].

Mark a straight level line. Align the top of the

template with the marked line and temporarily

secure the template to the wall with a tack or

non-marking tape [FIG. 3b].

Place a mark through the template's paper at

each indicated crosshair (four bi-directional

keyway holes), then remove the template from

the wall [FIG. 3c].

Note: DO NOT FLIP THE TEMPLATE! e

dimensions of the template are accurate to

either orientation of the Hose Reel. TheHoseReel should be mounted to a sturdy, reinforced wall (e.g.

concretewall,brick wall, wood-framed wall, etc.) Wall anchors can

beusedif mounting on drywall. This template indicates the proper

drillholesand the full, assembled size of the Hose Reel.

HoseReel Template

8-1/2"

216mm

9-3/4"

248mm

HoseReelTemplate

#ZBT000003

DrillHere

DrillHereDrillHere

DrillHere

LEVELTHIS LINE

TheHoseReel can be mounted so that the Handle is on either side

asthekeyholes are bi-directional. This does not require rotating the

templlate.Decidehow you want your Hose Reel oriented during

installationtobest meet your shop’sneeds.

HoseReel Mounting Positions

Rev:B20230314LL

FIG. 3b

FIG. 3a

FIG. 4

Mark

Here

Handle on

the left

Handle on

the right

Front View Front View

FIG. 3c

4 Using appropriate fasteners for the wall type

you are installing your system onto, drill into

and install fasteners into the wall at all marked

locations.

a. Maximum Fastener Size: 3/8" diameter

b. Maximum Washer Size: 5/8" outside

diameter

Place washers onto each fastener and thread

the fasteners into all four holes, leaving at least

1/2" outside of the hole to t the Hose Reel

Assembly [FIG. 4].

5oneida-air.com

FIG. 5a FIG. 5b

Assembly Instructions (Continued)

5 Li the Hose Reel Assembly up and over the

fasteners so that the washer is on the inside of

the Hose Reel [FIG 5a].

Slide the Hose Reel Assembly down so that the

fastener is snugly inside the smaller section of

each keyhole [FIG 5b].

Wall

6 Tighten these four fasteners to secure the Hose

Reel Assembly to the wall [FIG. 6].

Note: If installing over drywall, avoid

overtightening as it may damage the wall.

7 Clamp the Turn Key Hose Clamp (K) onto

one end of the Hose (J) [FIG. 7].

FIG. 7

FIG. 6

Assembly Instructions

6Oneida Air Systems

Assembly Instructions (Continued)

8 Feed the clamped end of the Hose (J) through

the access hole in the Core (A1) closest to the

Handle Side Assembly (A3) [FIG. 8a]. Then

attach the Hose to the Outlet Coupler (C). You

can guide the Hose by using the other access

hole in the Core closest to the Outlet & Brake

Side Assembly (A4) [FIG 8b].

FIG. 8a

FIG. 8b

Interior

View

7oneida-air.com

10 Guide the Hose (J) as you wind it around the

Core (A1) of the Body Assembly (A) so it is

neatly wrapped as shown in [FIG. 10].

Assembly Instructions (Continued)

9 Secure the Hose (J) to the Handle Side

Assembly (A3) with the Self-tapping Screw

(I) [FIG 9].

FIG.9

Customer Service Dept.

1-866-387-8822 • support@oneida-air.com

1001 West Fayette Street, Syracuse, NY 13204 U.S.A.

ank you for your business!

Regardless of where you purchased your system, if you have any

questions or issues with missing / damaged parts, please call

Oneida Air Systems rst to let us help resolve your problem.

We fully stand behind the quality of our product and place the

utmost value on our customer’s satisfaction.

We want to do everything possible to make your purchase and

experience with Oneida Air Systems a good one!

Inhaltsverzeichnis

Andere Oneida Air Systems Werkzeuge Handbücher

Oneida Air Systems

Oneida Air Systems AHR000025 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung

Goobay

Goobay 97790 Bedienungsanleitung